SNAS880A December   2024  – October 2025 LMK3C0105

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 I2C Interface Specification
  7. 6 Parameter Measurement Information
    1. 6.1 Output Format Configurations
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Device Block-Level Description
      2. 7.3.2 Device Configuration Control
      3. 7.3.3 OTP Mode
      4. 7.3.4 I2C Mode
    4. 7.4 Device Functional Modes
      1. 7.4.1 Fail-Safe Inputs
      2. 7.4.2 Fractional Output Dividers
        1. 7.4.2.1 FOD Operation
        2. 7.4.2.2 Digital State Machine
        3. 7.4.2.3 Spread-Spectrum Clocking
        4. 7.4.2.4 Integer Boundary Spurs
      3. 7.4.3 Output Behavior
        1. 7.4.3.1 Output Format Selection
        2. 7.4.3.2 REF_CTRL Operation
      4. 7.4.4 Output Enable
        1. 7.4.4.1 Output Enable Control
        2. 7.4.4.2 Output Enable Polarity
        3. 7.4.4.3 Separate Output Enable
        4. 7.4.4.4 Output Disable Behavior
      5. 7.4.5 Device Default Settings
    5. 7.5 Programming
      1. 7.5.1 I2C Serial Interface
      2. 7.5.2 One-Time Programming Sequence
  9. 8 Device Registers
    1. 8.1 Register Maps
      1. 8.1.1  R0 Register (Address = 0x0) [reset = 0x0861/0x0863]
      2. 8.1.2  R1 Register (Address = 0x1) [reset = 0x5599]
      3. 8.1.3  R2 Register (Address = 0x2) [reset = 0xC28F]
      4. 8.1.4  R3 Register (Address = 0x3) [reset = 0x1804]
      5. 8.1.5  R4 Register (Address = 0x4) [reset = 0x0000]
      6. 8.1.6  R5 Register (Address = 0x5) [reset = 0x0000]
      7. 8.1.7  R6 Register (Address = 0x6) [reset = 0x0AA7]
      8. 8.1.8  R7 Register (Address = 0x7) [reset = 0x5D1F]
      9. 8.1.9  R8 Register (Address = 0x8) [reset = 0xC28F]
      10. 8.1.10 R9 Register (Address = 0x9) [reset = 0x3000/0x1000]
      11. 8.1.11 R10 Register (Address = 0xA) [reset = 0x0010]
      12. 8.1.12 R11 Register (Address = 0xB) [reset = 0x0000]
      13. 8.1.13 R12 Register (Address = 0xC) [reset = 0xE800]
      14. 8.1.14 R238 Register (Address = 0xEE) [reset = 0x0000]
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Application Block Diagram Examples
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
      4. 9.2.4 Example: Changing Output Frequency
      5. 9.2.5 Crosstalk
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Power-Up Sequencing
      2. 9.3.2 Decoupling Power Supply Inputs
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

7.4.5 Device Default Settings

Table 7-8 summarizes the default settings of the LMK3C0105V33 and LMK3C0105V18 at start-up for the four OTP pages. In I2C mode, the Page 0 settings are loaded. For a full list of every default register setting, see Device Registers.

Table 7-8 LMK3C0105 Start-up Settings
ParameterOTP Page 0OTP Page 1OTP Page 2OTP Page 3
VDD Supply Voltage

3.3V (LMK3C0105V33)

1.8V (LMK3C0105V18)

OUTA/OUTB Frequency25MHz25MHz25MHz25MHz
OUTA/OUTB Output FormatLVCMOS, In-PhaseLVCMOS, In-PhaseLVCMOS, In-PhaseLVCMOS, In-Phase
OUTA/OUTB EnableEnableEnableEnableEnable
OUTA/OUTB Disable BehaviorGNDGNDGNDGND
OUTC/OUTD Frequency25MHz25MHz25MHz25MHz
OUTC/OUTD Output FormatLVCMOS, In-PhaseLVCMOS, In-PhaseLVCMOS, In-PhaseLVCMOS, In-Phase
OUTC/OUTD EnableEnableEnableEnableEnable
OUTC/OUTD Disable BehaviorGNDGNDGNDGND
REF_CTRL BehaviorREF_CLK, 25MHzREF_CLK, 25MHzREF_CLK, 25MHzREF_CLK, 25MHz
FOD0 Frequency200MHz200MHz200MHz200MHz
FOD1 Frequency200MHz200MHz200MHz200MHz
SSC EnableDisableEnableEnableEnable
SSC Modulation TypeDown-spreadDown-spreadDown-spreadDown-spread
SSC Modulation Depth0%–0.1%–0.3%–0.5%
Pin 2 Function I2C Address LSB Selection I2C Address LSB Selection I2C Address LSB Selection I2C Address LSB Selection