SNOSDL9B December   2024  – May 2026 LMG5126

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Device Configuration
      2. 6.3.2  Device Enable/Disable (UVLO/EN)
      3. 6.3.3  Multi-Device Operation
      4. 6.3.4  Switching Frequency and Synchronization (SYNCIN)
      5. 6.3.5  Dual Random Spread Spectrum (DRSS)
      6. 6.3.6  Operation Modes (BYPASS, DEM, FPWM)
      7. 6.3.7  VCC Regulator, BIAS (BIAS-pin, VCC-pin)
      8. 6.3.8  Soft Start (SS-pin)
      9. 6.3.9  VOUT Programming (VOUT, ATRK, DTRK)
      10. 6.3.10 Protections
        1. 6.3.10.1 VOUT Overvoltage Protection (OVP)
        2. 6.3.10.2 Thermal Shutdown (TSD)
      11. 6.3.11 Power-Good Indicator (PGOOD-pin)
      12. 6.3.12 Slope Compensation (CSA, CSB)
      13. 6.3.13 Current Sense Setting and Switch Peak Current Limit (CSA, CSB)
      14. 6.3.14 Input Current Limit and Monitoring (ILIM, IMON, DLY)
      15. 6.3.15 Maximum Duty Cycle and Minimum Controllable On-time Limits
      16. 6.3.16 GAN Drivers, Integrated Boot Capacitor and Diode, and Hiccup Mode Fault Protection
      17. 6.3.17 Signal Deglitch Overview
    4. 6.4 Device Functional Modes
      1. 6.4.1 Shutdown State
  8. 7 Application and Implementation
    1. 7.1 Application Information
      1. 7.1.1 Feedback Compensation
    2. 7.2 Typical Application
      1. 7.2.1 Application
      2. 7.2.2 Design Requirements
      3. 7.2.3 Detailed Design Procedure
        1. 7.2.3.1  Custom Design With WEBENCH® Tools
        2. 7.2.3.2  Determine the Total Phase Number
        3. 7.2.3.3  Determining the Duty Cycle
        4. 7.2.3.4  Timing Resistor RT
        5. 7.2.3.5  Inductor Selection Lm
        6. 7.2.3.6  Current Sense Resisitor Rcs
        7. 7.2.3.7  Current Sense Filter RCSFA, RCSFB, CCS
        8. 7.2.3.8  Snubber Components
        9. 7.2.3.9  Vout Programming
        10. 7.2.3.10 Input Current Limit (ILIM/IMON)
        11. 7.2.3.11 Minimum Load Resistor
        12. 7.2.3.12 UVLO Divider
        13. 7.2.3.13 Soft Start
        14. 7.2.3.14 Output Capacitor Cout
        15. 7.2.3.15 Input Capacitor Cin
        16. 7.2.3.16 VCC Capacitor CVCC
        17. 7.2.3.17 BIAS Capacitor
        18. 7.2.3.18 VOUT Capacitor
        19. 7.2.3.19 Loop Compensation
      4. 7.2.4 Application Curves
        1. 7.2.4.1 Efficiency
        2. 7.2.4.2 Steady State Waveforms
        3. 7.2.4.3 Step Load Response
        4. 7.2.4.4 Thermal Performance
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Third-Party Products Disclaimer
      2. 8.1.2 Development Support
        1. 8.1.2.1 Custom Design With WEBENCH® Tools
    2. 8.2 Documentation Support
      1. 8.2.1 Related Documentation
    3. 8.3 Receiving Notification of Documentation Updates
    4. 8.4 Support Resources
    5. 8.5 Trademarks
    6. 8.6 Electrostatic Discharge Caution
    7. 8.7 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

1 Features

  • Input voltage 6.5V to 42V
    • Minimum 2.5V for V(BIAS) ≥ 6.5V or VOUT ≥ 6V
  • Output Voltage 6V to 60V
    • 2% accuracy, internal feedback resistors
    • Bypass operation for VI > VOUT
      • Boot refresh out of audio >20kHz
    • Dynamic output voltage tracking
      • Digital PWM tracking (DTRK)
      • Analog tracking (ATRK)
    • Over voltage protection (65V, 50V, 35V, 25V)
  • Low shutdown ISD of 5μA typical (100uA maximum)
  • Low operating IQ of 1.5mA typical (2.5mA maximum)
  • Stacking with interleaved multiphase operation
    • Up to 4-devices without external clock
  • Switching frequency from 300kHz to 2.5MHz
    • Synchronization to external clock (SYNCIN)
    • Spread Spectrum (DRSS)
  • Dynamically selectable switching modes (FPWM, Diode emulation)
  • Current sense resistor or DCR sensing
  • Average inductor current monitor
  • Average input current limit
  • Selectable current limit (29mV or 60mV)
  • Selectable delay time (DLY)
  • Power good indicator
  • Programmable VI undervoltage lockout (UVLO)
  • Lead-less RLF-22 package with wettable flanks
  • Create a custom design using the LMG5126 with the WEBENCH® Power Designer