SPRUJ12F August   2021  – January 2024

1.   1
2.   Abstract
3.   Trademarks
4. 1Preface: Read This First
   1. 1.1 If You Need Assistance
   2. 1.2 Important Usage Notes
5. 2Kit Overview
   1. 2.1 Kit Contents
   2. 2.2 Key Features
   3. 2.3 Component Identification
   4. 2.4 BoosterPacks
   5. 2.5 Compliance
   6. 2.6 Security
6. 3Board Setup
   1. 3.1 Power Requirements
      1. 3.1.1 Power Input Using USB Type-C Connector
      2. 3.1.2 Power Status LED's
      3. 3.1.3 Power Tree
      4. 3.1.4 Power Sequence
   2. 3.2 Push Buttons
   3. 3.3 Boot Mode Selection
7. 4Hardware Description
   1. 4.1  Functional Block Diagram
   2. 4.2  BoosterPack Headers
      1. 4.2.1 Pinmux for BoosterPack
   3. 4.3  GPIO Mapping
   4. 4.4  Reset
   5. 4.5  Clock
   6. 4.6  Memory Interface
      1. 4.6.1 QSPI Interface
      2. 4.6.2 Board ID EEPROM
   7. 4.7  Ethernet Interface
      1. 4.7.1 Ethernet PHY Strapping
      2. 4.7.2 Ethernet PHY - Power, Clock, Reset, Interrupt
      3. 4.7.3 LED indication in Ethernet RJ45 Connector
   8. 4.8  USB 2.0 Interface
   9. 4.9  I2C Interface
   10. 4.10 Industrial Application LEDs
   11. 4.11 UART Interface
   12. 4.12 eQEP Interface
   13. 4.13 CAN Interface
   14. 4.14 FSI Interface
   15. 4.15 JTAG Emulation
   16. 4.16 Test Automation Interface
   17. 4.17 SPI Interface
8. 5References
   1. 5.1 Reference Documents
   2. 5.2 Other TI Components Used in This Design
9.   A E3 Design Changes
10.   B Revision A Design Changes
11.   Revision History

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2023, Texas Instruments Incorporated