Home Batteriemanagement-ICs Batterielader-ICs
Home
Batteriemanagement-ICs
Batterielader-ICs
NEU

BQ25690

AKTIV

Eigenständiger oder I²C-gesteuerter bidirektionaler Abwärts/Aufwärts-Lader mit Leistungspfad, 34 

Jetzt bestellen
Datenblatt

BQ25690

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Rating Catalog Number of series cells 1, 2, 3, 4, 5, 6, 7 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4, SuperCap Charge current (max) (A) 3 Features BAT temp thermistor monitoring (JEITA profile), BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation, IINDPM (Input current limit), Input OVP, Integrated ADC, Power Path, Solar input/MPPT, USB C/PD compatible, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Vin (min) (V) 2.5 Vin (max) (V) 34 Absolute max Vin (max) (V) 45 Control topology Switch-Mode Buck-boost Battery charge voltage (min) (V) 0 Battery charge voltage (max) (V) 33 Control interface I2C, Standalone (RC-Settable) Operating temperature range (°C) -40 to 125
Rating Catalog Number of series cells 1, 2, 3, 4, 5, 6, 7 Cell chemistry Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4, SuperCap Charge current (max) (A) 3 Features BAT temp thermistor monitoring (JEITA profile), BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation, IINDPM (Input current limit), Input OVP, Integrated ADC, Power Path, Solar input/MPPT, USB C/PD compatible, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Vin (min) (V) 2.5 Vin (max) (V) 34 Absolute max Vin (max) (V) 45 Control topology Switch-Mode Buck-boost Battery charge voltage (min) (V) 0 Battery charge voltage (max) (V) 33 Control interface I2C, Standalone (RC-Settable) Operating temperature range (°C) -40 to 125
WQFN-HR (RBA) 26 14 mm² 3.5 x 4
  • High integration buck-boost forward (sink) mode charger for 1- to 7cell Li-Ion batteries supporting USB PD profile with integrated switching MOSFETs and loop compensation
  • Highly efficient
    • Programmable switching frequency from 450kHz to 1.2MHz
    • Bypass mode for >98.0% efficiency USB-PD PPS direct battery charging at 20V, 3A
    • Selectable PFM with out-of-audio (OOA) operation for light load efficiency improvement
  • Supports a wide range of input sources with 2.5V to 34V operating range and 45V absolute maximum rating
    • Support VIN down to 2.5V with VBAT > 3.2V
    • USB-PD input
    • Input voltage dynamic power management (VINDPM) up to 34V to avoid input crashing
    • Optional input current dynamic power management (IINDPM) up-to 3.3A for maximum power limit
  • Optional Narrow voltage DC (NVDC) power path management
    • System instant-on with depleted or no battery
    • Battery supplements system when the adapter is fully loaded
  • I2C controlled for optimal system performance with resistor-programmable option
    • Hardware selectable default cell count, charge voltage, input and charge current limits
    • 3.3A charging current with 20mA resolution
  • Reverse/OTG (source) mode powers input port from battery
    • 3.5V to 34V reverse output voltage with 20mV resolution to support USB-PD PPS
    • Up-to 3.3A reverse output current regulation with 20mA resolution to support USB-PD PPS
  • Low quiescent current
    • 6.5µA for battery only operation
    • 700µA for converter switching operation
  • High accuracy
    • ±0.5% charge voltage regulation
    • ±5% input/output current regulation
  • Safety
    • Input and battery OVP
    • Thermal regulation and thermal shutdown
    • Converter MOSFETs OCP
    • Charging safety timer
  • High integration buck-boost forward (sink) mode charger for 1- to 7cell Li-Ion batteries supporting USB PD profile with integrated switching MOSFETs and loop compensation
  • Highly efficient
    • Programmable switching frequency from 450kHz to 1.2MHz
    • Bypass mode for >98.0% efficiency USB-PD PPS direct battery charging at 20V, 3A
    • Selectable PFM with out-of-audio (OOA) operation for light load efficiency improvement
  • Supports a wide range of input sources with 2.5V to 34V operating range and 45V absolute maximum rating
    • Support VIN down to 2.5V with VBAT > 3.2V
    • USB-PD input
    • Input voltage dynamic power management (VINDPM) up to 34V to avoid input crashing
    • Optional input current dynamic power management (IINDPM) up-to 3.3A for maximum power limit
  • Optional Narrow voltage DC (NVDC) power path management
    • System instant-on with depleted or no battery
    • Battery supplements system when the adapter is fully loaded
  • I2C controlled for optimal system performance with resistor-programmable option
    • Hardware selectable default cell count, charge voltage, input and charge current limits
    • 3.3A charging current with 20mA resolution
  • Reverse/OTG (source) mode powers input port from battery
    • 3.5V to 34V reverse output voltage with 20mV resolution to support USB-PD PPS
    • Up-to 3.3A reverse output current regulation with 20mA resolution to support USB-PD PPS
  • Low quiescent current
    • 6.5µA for battery only operation
    • 700µA for converter switching operation
  • High accuracy
    • ±0.5% charge voltage regulation
    • ±5% input/output current regulation
  • Safety
    • Input and battery OVP
    • Thermal regulation and thermal shutdown
    • Converter MOSFETs OCP
    • Charging safety timer

The BQ25690 is a fully integrated, switch-mode buck-boost charger for 1 cell to 7cell Li-ion or Li-polymer batteries. The wide input voltage range from 2.5V to 34V supports applications powered from batteries, standard USB-PD adapters, and high voltage dedicated DC adapters. The device integrates 4 switching MOSFETs (Q1, Q2, Q3, Q4) and all the loop compensation of the buck-boost converter for small solution size with simple design. The device uses NVDC power path management, regulating the system slightly above the battery voltage without dropping below a configurable minimum system voltage. When system power exceeds the input source rating, battery supplement mode supports the system without overloading the input source. The device also supports the full input (sink) and output (reverse or source mode) voltage ranges for USB Type-C and USB power delivery (USB-PD) applications.

The BQ25690 is a fully integrated, switch-mode buck-boost charger for 1 cell to 7cell Li-ion or Li-polymer batteries. The wide input voltage range from 2.5V to 34V supports applications powered from batteries, standard USB-PD adapters, and high voltage dedicated DC adapters. The device integrates 4 switching MOSFETs (Q1, Q2, Q3, Q4) and all the loop compensation of the buck-boost converter for small solution size with simple design. The device uses NVDC power path management, regulating the system slightly above the battery voltage without dropping below a configurable minimum system voltage. When system power exceeds the input source rating, battery supplement mode supports the system without overloading the input source. The device also supports the full input (sink) and output (reverse or source mode) voltage ranges for USB Type-C and USB power delivery (USB-PD) applications.
filter Andere Batterielader-ICs suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 1
Top-Dokumentation Typ Titel Format-Optionen Datum
* Data sheet BQ25690 Standalone/I2C Controlled, 1-7 cell Li-Ion, 3A Buck-Boost Bidirectional Battery Charger with Bypass datasheet (Rev. A) 16 Dez 2025

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

BQ25690EVM — BQ25690 – Evaluierungsmodul

Das Evaluierungsmodul BQ2569X/9X-Q1 (EVM) wird zur Evaluierung des integrierten Schaltkreises BQ2569X/9X-Q1 verwendet. Der BQ2569X/9X-Q1 ist ein integrierter Switchmode-Abwärts-/Aufwärts-Akkulademanagement-Baustein im HOTROD (QFN)-Gehäuse, der für Lithium-Ionen-Akkus mit Zellen der Serie 1 bis 7 (...)
Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
Berechnungstool

BQ2569X-DESIGN-CALC — BQ2569X design spreadsheet

Excel spreadsheet to help with BQ2569X battery charger designs
Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware
Herunterladen
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
WQFN-HR (RBA) 26 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos