Startseite Motortreiber Treiber für Gleichstrom-Bürstenmotoren
Startseite
Motortreiber
Treiber für Gleichstrom-Bürstenmotoren
NEU

DRV8002-Q1

AKTIV

40 V-Multifunktions-Halbbrücken und Highside-Treiber für Hintertürsteuerung und Fensterheber für

Jetzt bestellen
Datenblatt

DRV8002-Q1

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 8 Control mode PWM Control interface SPI Features Current sense Amplifier, Current sense output, Open-Load Detection Topology External FET, Integrated FET, Multichannel Rating Automotive TI functional safety category Functional Safety-Compliant Operating temperature range (°C) -40 to 125
Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 8 Control mode PWM Control interface SPI Features Current sense Amplifier, Current sense output, Open-Load Detection Topology External FET, Integrated FET, Multichannel Rating Automotive TI functional safety category Functional Safety-Compliant Operating temperature range (°C) -40 to 125
VQFN (RGZ) 48 49 mm² 7 x 7
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Compliant Targeted
    • Developed for functional safety applications
    • Documentation to aid ISO26262 system design
    • Systematic integrity up to ASIL D
    • Hardware integrity up to ASIL B
  • 5V to 35V (40V abs. max) operating range
  • H-bridge or dual-channel half-bridge gate drivers
    • Smart gate drive architecture
    • Tripler charge pump for 100% PWM
    • Wide common mode current shunt amplifier
  • 1 Integrated half-bridge with IOUT max 8A (RDSON HS +LS FET = 155mΩ)
  • 1 Integrated half-bridge with IOUT max 7A (RDSON HS +LS FET = 185mΩ)
  • 2 Integrated half-bridges with IOUT max 4A (RDSON HS +LS FET = 440mΩ)
  • 2 Integrated half-bridges with IOUT max 1.3A load (RDSON HS +LS FET = 1540mΩ)
  • 1 Configurable integrated high-side driver as lamp or LED driver with IOUT Max 1.5/0.5A (RDSON = 0.4/1.2Ω)
  • 5 Configurable integrated high-side drivers for 0.5/0.25A load (RDSON = 1.2Ω)
  • Internal 10bit PWM generator for high-side drivers
  • All high-side drivers support a low- or high- current threshold constant current mode to drive a wide range of LED modules
  • Integrated driver output features current regulation (ITRIP)
  • Muxable sense output (IPROPI)
    • Internal current sensing with proportional current output (IPROPI)
    • Advanced die temperature monitoring with multiple thermal clusters
    • Motor supply voltage monitor
  • Protection and diagnostic features with configurable fault behavior
    • Load diagnostics in both the off-state and on-state to detect open load and short-circuit
    • Overcurrent and over temperature protection
  • Device Comparison Table
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Compliant Targeted
    • Developed for functional safety applications
    • Documentation to aid ISO26262 system design
    • Systematic integrity up to ASIL D
    • Hardware integrity up to ASIL B
  • 5V to 35V (40V abs. max) operating range
  • H-bridge or dual-channel half-bridge gate drivers
    • Smart gate drive architecture
    • Tripler charge pump for 100% PWM
    • Wide common mode current shunt amplifier
  • 1 Integrated half-bridge with IOUT max 8A (RDSON HS +LS FET = 155mΩ)
  • 1 Integrated half-bridge with IOUT max 7A (RDSON HS +LS FET = 185mΩ)
  • 2 Integrated half-bridges with IOUT max 4A (RDSON HS +LS FET = 440mΩ)
  • 2 Integrated half-bridges with IOUT max 1.3A load (RDSON HS +LS FET = 1540mΩ)
  • 1 Configurable integrated high-side driver as lamp or LED driver with IOUT Max 1.5/0.5A (RDSON = 0.4/1.2Ω)
  • 5 Configurable integrated high-side drivers for 0.5/0.25A load (RDSON = 1.2Ω)
  • Internal 10bit PWM generator for high-side drivers
  • All high-side drivers support a low- or high- current threshold constant current mode to drive a wide range of LED modules
  • Integrated driver output features current regulation (ITRIP)
  • Muxable sense output (IPROPI)
    • Internal current sensing with proportional current output (IPROPI)
    • Advanced die temperature monitoring with multiple thermal clusters
    • Motor supply voltage monitor
  • Protection and diagnostic features with configurable fault behavior
    • Load diagnostics in both the off-state and on-state to detect open load and short-circuit
    • Overcurrent and over temperature protection
  • Device Comparison Table

The DRV8002-Q1 device integrates multiple door control specific functions: driving and diagnosing motor (inductive), resistive and capacitive loads, driving a lamp or LEDs. These drivers include protection features for offline and active diagnostics such as under and over voltage monitors, offline open load and short-circuit diagnostics, and zone-based thermal monitoring and shutdown protection. The device features two half-bridge gate drivers, 6 integrated half-bridges (2 high-side alternate modes) and 6 integrated high-side drivers. The half-bridgeand high-side drivers have PWM input control configuration, sensing, diagnostics and device system protection. There is a dedicated internal programmable PWM generators for each high-side driver. Proportional current sense pin output is available for all integrated drivers, along with a robust and flexible current shunt amplifier for the gate driver.

The DRV8002-Q1 device integrates multiple door control specific functions: driving and diagnosing motor (inductive), resistive and capacitive loads, driving a lamp or LEDs. These drivers include protection features for offline and active diagnostics such as under and over voltage monitors, offline open load and short-circuit diagnostics, and zone-based thermal monitoring and shutdown protection. The device features two half-bridge gate drivers, 6 integrated half-bridges (2 high-side alternate modes) and 6 integrated high-side drivers. The half-bridgeand high-side drivers have PWM input control configuration, sensing, diagnostics and device system protection. There is a dedicated internal programmable PWM generators for each high-side driver. Proportional current sense pin output is available for all integrated drivers, along with a robust and flexible current shunt amplifier for the gate driver.
filter Andere Treiber für Gleichstrom-Bürstenmotoren suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 1
Typ Titel Datum
* Data sheet DRV8002-Q1 Automotive Highly-Integrated, Multifunction Driver for Door Control datasheet PDF | HTML 27 Aug 2025

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
VQFN (RGZ) 48 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos