Startseite Energiemanagement Mehrkanal-ICs (PMICs)
NEU

LP87725-Q1

AKTIV

PMIC für die Automobilindustrie mit drei rauscharmen 3-A-Abwärtswandlern, IO-LDO und Lastschalter fü

Produktdetails

Processor supplier Texas Instruments Processor name mmWave AWR, mmWave IWR Regulated outputs (#) 5 Step-down DC/DC converter 3 LDO 1 Vin (min) (V) 3 Vin (max) (V) 4 Vout (min) (V) 0.9 Vout (max) (V) 1.8 Iout (max) (A) 3 TI functional safety category Functional Safety-Compliant Configurability Factory programmable, Software configurable Features Output Short-Circuit and Overload Protection, Overtemperature warning and protection, Overvoltage protection, SPI, UVLO Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.02 Switching frequency (max) (kHz) 19200 Shutdown current (ISD) (typ) (µA) 20 Switching frequency (typ) (kHz) 17600
Processor supplier Texas Instruments Processor name mmWave AWR, mmWave IWR Regulated outputs (#) 5 Step-down DC/DC converter 3 LDO 1 Vin (min) (V) 3 Vin (max) (V) 4 Vout (min) (V) 0.9 Vout (max) (V) 1.8 Iout (max) (A) 3 TI functional safety category Functional Safety-Compliant Configurability Factory programmable, Software configurable Features Output Short-Circuit and Overload Protection, Overtemperature warning and protection, Overvoltage protection, SPI, UVLO Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.02 Switching frequency (max) (kHz) 19200 Shutdown current (ISD) (typ) (µA) 20 Switching frequency (typ) (kHz) 17600
VQFN-HR (RAG) 24 16 mm² 4 x 4
  • AEC-Q100 qualified with the following results:
    • Device temperature grade 1: –40°C to +125°C ambient operating temperature
  • Functional safety-compliant device
    • Developed for functional safety applications
    • Documentation to aid ISO 26262 functional safety system design up to ASIL-B
    • BUCK, LDO and load switch output and Input supply overvoltage and undervoltage monitoring
    • Q&A Watchdog
    • Level or PWM error signal monitor (ESM)
    • ABIST and CRC
  • Input voltage: 3.3 V nominal (3 V to 4 V range)
  • 3 high-efficiency, low noise, high frequency step-down DC/DC converters:
    • Output voltage: 0.8 V, 0.82 V, 0.9 V to 1.9 V with 20 mV output voltage step
    • Maximum output current: 3.5 A
    • Switching frequency: 4.4 MHz, 8.8 MHz, and 17.6 MHz
  • 600 mA linear regulator with bypass \ load switch mode (LDO_LS1)
    • Input voltage, LDO mode: 1.2 V to 4 V
    • Output voltage: 0.6 V to 3.4 V with 50 mV output voltage step
    • Input voltage, bypass \ load switch mode: 1.6 V to 3.4 V
  • 400 mA load switch (LS2)
    • Input voltage range: 1.6 V to 3.6 V
    • On resistance 3.3-V input, 200 mA: 75 mΩ -typ
  • Output short-circuit and overload protection
  • Regulator output dynamic voltage scaling (DVS) through I2C interface
  • Input overvoltage protection (OVP) and undervoltage lockout (UVLO)
  • Two general purpose voltage monitors shared with LDO_LS1 and LS2 output
  • Overtemperature warning and protection
  • I2C interface supporting standard, fast mode, fast-mode+ and optional I2C address selection
  • AEC-Q100 qualified with the following results:
    • Device temperature grade 1: –40°C to +125°C ambient operating temperature
  • Functional safety-compliant device
    • Developed for functional safety applications
    • Documentation to aid ISO 26262 functional safety system design up to ASIL-B
    • BUCK, LDO and load switch output and Input supply overvoltage and undervoltage monitoring
    • Q&A Watchdog
    • Level or PWM error signal monitor (ESM)
    • ABIST and CRC
  • Input voltage: 3.3 V nominal (3 V to 4 V range)
  • 3 high-efficiency, low noise, high frequency step-down DC/DC converters:
    • Output voltage: 0.8 V, 0.82 V, 0.9 V to 1.9 V with 20 mV output voltage step
    • Maximum output current: 3.5 A
    • Switching frequency: 4.4 MHz, 8.8 MHz, and 17.6 MHz
  • 600 mA linear regulator with bypass \ load switch mode (LDO_LS1)
    • Input voltage, LDO mode: 1.2 V to 4 V
    • Output voltage: 0.6 V to 3.4 V with 50 mV output voltage step
    • Input voltage, bypass \ load switch mode: 1.6 V to 3.4 V
  • 400 mA load switch (LS2)
    • Input voltage range: 1.6 V to 3.6 V
    • On resistance 3.3-V input, 200 mA: 75 mΩ -typ
  • Output short-circuit and overload protection
  • Regulator output dynamic voltage scaling (DVS) through I2C interface
  • Input overvoltage protection (OVP) and undervoltage lockout (UVLO)
  • Two general purpose voltage monitors shared with LDO_LS1 and LS2 output
  • Overtemperature warning and protection
  • I2C interface supporting standard, fast mode, fast-mode+ and optional I2C address selection

The LP8772x-Q1 device is designed to meet the power management requirements of the AWR, IWR, and other MMICs in various automotive and industrial radar applications. The device has three step-down DC/DC converters, a LDO regulator, and a load switch. The LDO is powered externally and intended for supplying Ethernet device or any other device in the system. The load switch is intended to cut off the 3.3 V IO supply during the sensor sleep mode. The device is controlled by I2C communication interface and by enable signals.

The low noise step-down DC/DC converters support factory programmed switching frequency of 17.6 MHz or 8.8 MHz or 4.4 MHz. High switching frequency and low noise across wide frequency range, enables LDO-free power solution which helps to reduce the solution cost and improve thermal performance. The switching clock is forced to PWM mode for excellent RF performance and can also be synchronized to an external clock. The LP8772x-Q1 device supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) which improves the accuracy of the output voltage.

The LP8772x-Q1 device supports programmable start-up and shutdown delays and sequences which are synchronized to the ENABLE signal. These sequences can also include GPO signal to control external regulators, load switches, and processor reset. The default settings for the device are programmed into nonvolatile memory (NVM) / one time programmable (OTP) memory at the factory and user cannot change the device default NVM / OTP settings. The device controls the output slew rate to minimize output voltage overshoot and in-rush current during device start-up.

The LP8772x-Q1 device is designed to meet the power management requirements of the AWR, IWR, and other MMICs in various automotive and industrial radar applications. The device has three step-down DC/DC converters, a LDO regulator, and a load switch. The LDO is powered externally and intended for supplying Ethernet device or any other device in the system. The load switch is intended to cut off the 3.3 V IO supply during the sensor sleep mode. The device is controlled by I2C communication interface and by enable signals.

The low noise step-down DC/DC converters support factory programmed switching frequency of 17.6 MHz or 8.8 MHz or 4.4 MHz. High switching frequency and low noise across wide frequency range, enables LDO-free power solution which helps to reduce the solution cost and improve thermal performance. The switching clock is forced to PWM mode for excellent RF performance and can also be synchronized to an external clock. The LP8772x-Q1 device supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) which improves the accuracy of the output voltage.

The LP8772x-Q1 device supports programmable start-up and shutdown delays and sequences which are synchronized to the ENABLE signal. These sequences can also include GPO signal to control external regulators, load switches, and processor reset. The default settings for the device are programmed into nonvolatile memory (NVM) / one time programmable (OTP) memory at the factory and user cannot change the device default NVM / OTP settings. The device controls the output slew rate to minimize output voltage overshoot and in-rush current during device start-up.

Herunterladen Video mit Transkript ansehen Video
Weitere Informationen anfordern

Das vollständige Datenblatt und weitere Informationen sind verfügbar. Jetzt anfordern

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 1
Typ Titel Datum
* Data sheet LP8772x-Q1 Three Buck Converters, One Linear Regulator and One Load Switch for mmWave Radar Sensors datasheet PDF | HTML 18 Dez 2023

Design und Entwicklung

Lösungen für die Stromversorgung

Lösungen erkunden, die den LP87725-Q1 umfassen. TI bietet Stromversorgungslösungen für Ein-Chip-Systeme (SoCs), Prozessoren, Mikrocontroller, Sensoren und feldprogrammierbare Gate-Arrays (FPGAs) von TI und von Fremdherstellern an.

Evaluierungsplatine

AWR2544LOPEVM — Evaluierungsmodul für den AWR2544LOP zur Realisierung eines Hochleistungs-SoC der zweiten Generation

Das AWR2544LOPEVM ist eine einfach zu handhabende Evaluierungsplatine für den mmWave-Sensorbaustein AWR254x mit direkter Verbindung zum DCA1000EVM. Dieses EVM-Kit enthält alles, was Sie für die Entwicklung von Software für den On-Chip-ARM Cortex-R5F-Controller und den Hardwarebeschleuniger (HWA (...)
Benutzerhandbuch: PDF
Evaluierungsplatine

LP87725Q1EVM — Evaluierungsmodul für den LP87725-Q1

Der LP87725-Q1-Baustein wurde entwickelt, um die Power-Management-Anforderungen der AWR- und IWR-MMICs verschiedener Radaranwendungen im Automobilbereich und in der Industrie zu erfüllen. Der Baustein verfügt über drei DC/DC-Abwärtswandler, einen LDO-Regler und einen Lastschalter. Der LDO wird (...)
Benutzerhandbuch: PDF | HTML
Simulationsmodell

LP8772X-Q1 PSpice Model

SNVMCC9.ZIP (46 KB) - PSpice Model
Simulationsmodell

LP8772X-Q1 SIMPLIS Model

SNVMCC8.ZIP (63 KB) - SIMPLIS Model
Berechnungstool

PEET-GUI — Effizienzschätzungstool für TPS6594-Q1, LP8756-Q1, LP8758, LP8770 und TPS650330-Q1

The PMIC Efficiency Estimator Tool (PEET GUI) is a graphical user interface used to easily evaluate PMIC DC/DC regulator efficiency relative to your design conditions. The PEET GUI can be used to configure each DC/DC regulator separately and provides real-time efficiency and power dissipation data (...)
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
VQFN-HR (RAG) 24 Ultra Librarian

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos