BQ27421-G1
- Single-Cell Li-Ion Battery Fuel Gauge
- Resides on System Board
- Supports Embedded or Removable Batteries
- Powered Directly from Battery with Integrated
LDO - Low-Value Integrated Sense Resistor
(7 mΩ, Typical)
- Easy-to-Configure Fuel Gauging Based on
Patented Impedance Track™ Technology- Reports Remaining Capacity and State-of-
Charge (SOC) with Smoothing Filter - Automatically Adjusts for Battery Aging, Self-
Discharge, Temperature, and Rate Changes - Battery State-of-Health (Aging) Estimation
- Reports Remaining Capacity and State-of-
- Microcontroller Peripheral Supports:
- 400-kHz I2C Serial Interface
- Configurable SOC Interrupt or
Battery Low Digital Output Warning - Internal Temperature Sensor or
Host-Reported Temperature
The Texas Instruments bq27421-G1 fuel gauge is a minimally configured microcontroller peripheral that provides system-side fuel gauging for single-cell Li-Ion batteries. The device requires very little user configuration and system microcontroller firmware development.
The bq27421-G1 fuel gauge uses the patented Impedance TrackTM algorithm for fuel gauging, and provides information such as remaining battery capacity (mAh), state-of-charge (%), and battery voltage (mV).
Battery fuel gauging with the bq27421-G1 fuel gauge requires connections only to PACK+ (P+) and PACK– (P–) for a removable battery pack or embedded battery circuit. The tiny 9-ball, 1.62 mm × 1.58 mm, 0.5-mm pitch NanoFree™ chip scale package (DSBGA) is ideal for space-constrained applications.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | bq27421-G1 System-Side Impedance Track Fuel Gauge With Integrated Sense Resistor datasheet (Rev. E) | PDF | HTML | 2016. 1. 6 | |
| * | 사용 설명서 | bq27421-G1 Technical Reference Manual (Rev. C) | 2016. 8. 15 | ||
| 기술 문서 | Get smart: How intelligent battery gauges improve battery life in continuous gluco | PDF | HTML | 2019. 4. 19 | ||
| 애플리케이션 노트 | Achieving The Successful Learning Cycle | PDF | HTML | 2018. 6. 19 | ||
| 애플리케이션 노트 | Simple Guide to Chemical ID Selection Tool (GPC) (Rev. A) | PDF | HTML | 2018. 6. 5 | ||
| 애플리케이션 노트 | Gauge Communication | 2017. 1. 12 | |||
| 애플리케이션 노트 | Theory and Implementation of Impedance Track Battery Fuel-Gauging Algorithm (Rev. A) | PDF | HTML | 2014. 5. 16 | ||
| 추가 자료 | Quickstart Guide for bq27421-G1 (Rev. B) | 2014. 5. 6 | |||
| 애플리케이션 노트 | Verification and Accuracy Test Methods of Gas Gauges | 2013. 6. 5 | |||
| 애플리케이션 노트 | Going to Production With the bq274xx Family of Gas Gauges | 2011. 6. 27 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BQ27421EVM-G1A — BQ27421EVM-G1A 시스템 측 배터리 연료(가스) 게이지 평가 모듈 보드
System-Side Battery Fuel (Gas) Gauge Solution Evaluation Module
The BQ27421EVM-G1A evaluation module is a complete evaluation system for the bq27421. The EVM includes one bq27421 circuit module with an integrated current-sense resistor. A separated orderable EV2400 PC interface board for gas gauge (...)BQ27421EVM-G1B — BQ27421EVM-G1B 시스템 측 배터리 연료(가스) 게이지 평가 모듈
System-Side Battery Fuel (Gas) Gauge Solution Evaluation Module
The BQ27421EVM-G1B evaluation module is a complete evaluation system for the bq27421. The EVM includes one bq27421 circuit module with an integrated current-sense resistor. A separated orderable EV2300 or EV2400 PC interface board for (...)EV2400 — 배터리 연료(가스) 게이지용 USB 기반 PC 인터페이스 평가 모듈
The EV2400 EVM interface board enables an IBM-compatible or other type PC (with the required driver for its particular platform) to communicate with the Texas Instruments SMBus or I2C interface gas gauges via a Universal Serial Bus (USB) port. In addition to this board, PC software is required to (...)
BQSTUDIO — bqStudio(Battery Management Studio) 소프트웨어
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
BQ27XXXSW-LINUX — BQ27XXX용 Linux 드라이버
The Linux driver supports the BQ27x series of Battery Fuel Gauges. The Linux driver supports communication through the I2C/HDQ bus and interfaces with the power supply sub-system to monitor battery properties.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
(...)
BQEVSW-MKST-UPDATE — Software Update to enable BQEVSW to use MKST-3P-ALT-EV2300
BQ-BATTERY-PROGRAMMER-SW 소프트웨어 개발 키트(SDK)는 TI 배터리 관리 제품을 사용하는 팩의 프로그래밍, 테스트 또는 조립 프로세스를 지원하는 강력한 소프트웨어 명령줄 툴 모음입니다. 이 소프트웨어의 실행 파일은 EV2300 통신 트랜스시버용 MKST-3P-ALT-EV2300 MKS 기술 대안과 함께 작동합니다. 실행 파일은 단일 스테이션에서 작동하지만 MKS Technology Inc.의 추가 소프트웨어 및 GUI를 사용하여 여러 스테이션으로 확장할 수 있습니다. 이 소프트웨어에는 여러 스테이션에 대한 (...)
TIDA-00031 — 통합 감지 레지스터를 사용하는 시스템 측 ImpedanceTrack 연료 게이지 레퍼런스 디자인
This reference design is a complete evaluation system solution for the bq27421. The solution includes one bq27421 circuit module with an integrated current-sense resistor. A separated orderable EV2300 or EV2400 PC interface board for gas gauge interface along with a PC USB cable, and (...)
TIDA-00042 — 1A 단일 입력, 싱글 셀 리튬 이온 배터리 충전기 레퍼런스 디자인
This reference design is targeted at space-limited portable applications. The devices in the design operate from either a USB port or AC adapter. The solution has a single power output that charges the battery. A system load can be placed in parallel with the battery as long as the average system (...)
TIDA-00044 — USB 리튬 이온 배터리 충전기 및 전력 경로 관리 레퍼런스 디자인
This reference design delivers up to 1000 mA of continuous current to the battery output when programmed with a resistor on the ISET pin and is programmed at the factory for ~540mA. The USB current limit modes are selected by the ISET2 pin and limits current to a maximum of 500 mA (logic high) or (...)
TIDA-00045 — 싱글 칩 충전 및 동적 전력 경로 관리 IC 레퍼런스 디자인
This reference design is a Single-Chip Charge and Dynamic Power-Path Management IC solution. It is a complete bq24030 based circuit design and provides a convenient method to evaluate the operation and performance of the IC. The development solution includes a tested evaluation board; a user guide (...)
TIDA-00053 — LiFePO4 애플리케이션용 1A 단일 셀 선형 충전기 레퍼런스 디자인
This reference design is designed to deliver up to 1 A of continuous current to the battery and/or system. It has a 4.9 VDC, 50 mA max internal LDO that can be used for USB applications or any other need. It uses the bq25070, a highly integrated LiFePO4 linear battery charger, in order to target (...)
TIDA-00055 — 2A FET를 지원하는 독립형 동기식 스위치 모드 리튬 이온 충전기 레퍼런스 디자인
This reference design is a solution for a Li-Ion charge management IC. It has a highly integrated battery charge IC utilizing synchronous switch mode power conversion for efficient and comprehensive charge control of a single cell Li-Ion battery. The solutionprovides a convenient method to evaluate (...)
TIDA-00586 — 게이지 부스터팩 레퍼런스 디자인
The TIDA-00586 reference design is a gauge that has been designed as a booster pack to fit on the TI Launchpad development boards. The use of this this board for development will reduce the time spent in design and test of the bq27421 gauge IC. You can select any appropriate charger to charge your (...)
TIDA-00669 — 게이지 포함 500mA 무선 충전기 부스터팩 레퍼런스 설계
TIDA-00669는 모든 TI LaunchPad™(www.ti.com/launchpad)에 전원을 공급하기 위한 무선 충전기 및 배터리 관리 기능을 제공하는 BoosterPack™ 레퍼런스 설계입니다. 이는 저전력 애플리케이션에 적합한 고집적 전력 관리 레퍼런스 설계입니다. 기본 저장 방법은 외부 리튬 폴리머 충전식 배터리입니다.
TIDA-00712 — 스마트워치 배터리 관리 솔루션 레퍼런스 설계
This reference design is for smartwatch battery management solution (BMS). It is suitable for low-power wearable devices like smartwatch applications. The design includes an ultra-low current 1 cell Li-ion linear charger; a highly integrated Qi-compliant wireless power receiver; a (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YZF) | 9 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.