DRV3245Q-Q1
- AEC-Q100 qualified for automotive applications:
- Device temperature grade 1: –40°C to +125°C, T A
- SafeTI™semiconductor component
- Developed according to the applicable requirements of ISO 26262
- 4.5-V to 45-V operating voltage
- Programmable peak gate drive currents up to 1A
- Charge-pump gate driver for 100% Duty Cycle
- Current-shunt amplifiers and phase comparators
- A / C Device: 3 current-shunt amplifiers (1) and 3-phase comparators with status through SPI (1)
- B Device: 2 current-shunt amplifiers and 3-phase comparators with real-time monitor through digital pins
- S Device: 3 current-shunt amplifiers
- 3-PWM or 6-PWM input control up to 20 kHz
- Single PWM-mode commutation capability
- Supports both 3.3-V and 5-V digital interface
- Serial peripheral interface (SPI)
- Thermally-enhanced 48-Pin HTQFP
- Protection features:
- Internal regulators, battery voltage monitor
- SPI CRC
- Clock monitor
- Analog built-in self test
- Programmable dead-time control
- MOSFET shoot-through prevention
- MOSFET V DS overcurrent monitors
- Gate-source voltage real time monitor
- Overtemperature warning and Shutdown
(1)C device : Low-drift offset high-precision amplifiers
The DRV3245Q-Q1 device is a FET gate driver IC for three-phase motor-drive applications designed according to the applicable requirements of ISO 26262 for functional safety applications. The device provides three half-bridge drivers each capable of driving a high-side and low-side N-channel MOSFET while also providing sophisticated protection and monitoring of the FETs. A charge-pump driver enables 100% duty cycle and supports low battery voltages during cold-crank operation. The integration of current-sense amplifiers, integrated phase comparators, and SPI-based configuration of the driver and its peripherals enable reduction of the bill of materials (BOM) and space on the printed circuit board (PCB) because of the elimination of most external and passive components.
The DRV3245Q-Q1 device also integrates diagnostics and protection for each internal block and provides support for common system diagnostic checks each of which can be instantiated and reported through SPI. This flexibility of the integrated features allows the device to integrate seamlessly into a variety of safety architectures.
관심 가지실만한 유사 제품
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | DRV3245Q-Q1 3-Phase Automotive Gate Driver Unit (GDU) With High Performance Sensing, Protection and Diagnostics datasheet (Rev. C) | PDF | HTML | 2023/04/11 |
| Functional safety information | Actuator Design Trends for Funct. Safety Sys. in Elect. and Autonomous Vehicles (Rev. A) | PDF | HTML | 2023/07/21 | |
| Application note | Best Practices for Board Layout of Motor Drivers (Rev. B) | PDF | HTML | 2021/10/14 | |
| White paper | 電気自動車と自動運転車の機能安全システムのアクチュエータ設計動向 | 2020/03/30 | ||
| Application note | Protecting Automotive Motor Drive Systems from Reverse Polarity Conditions (Rev. A) | 2019/02/19 | ||
| Application brief | Designing High-Side and 3-Phase Isolator MOSFET Circuits in Motor Apps | 2018/05/09 | ||
| Functional safety information | Analog components advance functional safety development for automotive applicati | 2017/01/20 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BOOSTXL-DRV3245AQ1 — DRV3245Q-Q1 오토모티브 3상 모터 게이트 드라이버 평가 모듈
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| HTQFP (PHP) | 48 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치