ISO1176T
- Meets or Exceeds the Requirements of EN 50170 and TIA/EIA-485-A
- Signaling Rates up to 40 Mbps
- Easy Isolated Power Design with Integrated Transformer Driver
- Typical Efficiency > 60% (I LOAD = 100 mA) - see SLUU471
- Differential Output exceeds 2.1 V (54-Ω Load)
- Low Bus Capacitance 10 pF (Maximum)
- Fail-safe Receiver for Bus Open, Short, or Idle
- 50-kV/µs Typical Transient Immunity
- Safety and Regulatory Approvals
- 4242 V PK Basic Insulation per DIN EN IEC 60747-17 (VDE 0884-17)
- 2500 V RMS Isolation for 1 minute per UL 1577
- CSA 60950-1 and CSA 61010-1 Standards
The ISO1176T is an isolated differential line transceiver with integrated oscillator outputs that provide the primary voltage for an isolation transformer. The device is ideal for long transmission lines because the ground loop is broken to allow the device to operate with a much larger common-mode voltage range.
The symmetrical isolation barrier of each device is tested to provide 4242V PK of isolation per VDE for 60 seconds between the line transceiver and the logic-level interface.
The galvanically isolated differential bus transceiver is an integrated circuit designed for bi-directional data communication on multipoint bus-transmission lines. The transceiver combines a galvanically isolated differential line driver and differential input line receiver. The driver has an active-high enable with isolated enable-state output on the ISODE pin (pin 10) to facilitate direction control. The driver differential outputs and the receiver differential inputs connect internally to form a differential input/output (I/O) bus port that is designed to offer minimum loading to the bus whenever the driver is disabled or V CC2 = 0.
Any cabled I/O can be subjected to electrical noise transients from various sources. These noise transients can cause damage to the transceiver and/or near-by sensitive circuitry if they are of sufficient magnitude and duration. The ISO1176T can significantly reduce the risk of data corruption and damage to expensive control circuits.
The device is characterized for operation over the ambient temperature range of –40°C to 85°C.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
ISO1176TEVM — ISO1176T 평가 모듈
This document describes the ISO1176T/35T/3086T Evaluation Module (EVM). It is used to evaluate the ISO1176T PROFIBUS Transceiver, the ISO35T RS-485 transceiver, or ISO3086T RS-485 Transceiver. Because the devices are similar transceivers, and the printed-circuit board is the same for all three (...)
ISO1176TEVM-433 — ISO1176T 소형 EVM
The smaller EVM version shows the customer the space required for their design. This circuit provides an isolated, 40 Mbps, 3.3V to 5V Profibus interface using the ISO1176T, isolated Profibus transceiver and the TPS high accuracy linear regulator. The circuit achieves signal and power isolation (...)
ISO35TEVM — ISO35T 평가 모듈
This document describes the ISO1176T/35T/3086T Evaluation Module (EVM). It is used to evaluate the ISO1176T PROFIBUS Transceiver, the ISO35T RS-485 transceiver, or ISO3086T RS-485 Transceiver. Because the devices are similar transceivers, and the printed-circuit board is the same for all three (...)
PROFIBUS — AM1810 ARM® MPU 및 OMAP-L138 DSP+ARM 프로세서의 PROFIBUS
PROFIBUS (Process Field Bus) is the world’s most successful field bus (communication) technology used in industrial automation and is overseen by the PROFIBUS and PROFINET International (PNO/PI) organization. PROFIBUS is a widely deployed technology, and by the end of 2009, there were over 30 (...)
TIDA-00005 — 절연 Profibus 인터페이스 레퍼런스 디자인
This reference design provides an isolated, 40-Mbps, 3.3-V to 5-V Profibus interface using the ISO1176T, isolated Profibus transceiver and the TPS76350 high-accuracy linear regulator. This circuit achieves signal and power isolation and at the same time decreases board space and power consumption.
TIDEP-0075 — 산업용 통신 게이트웨이 PROFINET IRT - PROFIBUS 마스터 레퍼런스 디자인
TIDEP0003 — 이더넷/IP 통신 개발 플랫폼
Targeted for Ethernet/IP secondary communications, this development platform allows you to implement Ethernet/IP communication standards in a broad range of industrial automation equipment. It enables low footprint designs in applications such as industrial automation, factory automation or (...)
TIDEP0008 — PROFINET 통신 개발 플랫폼
Targeted for PROFINET secondary communications, this reference design helps you implement PROFINET communications standards in a broad range of industrial automation equipment. It enables low-footprint designs in applications such as industrial automation, factory automation or (...)
TIDEP0027 — 산업 애플리케이션용 PRU-ICSS를 이용한 고성능 PTO(Pulse Train Output) 레퍼런스 디자인
The TIDEP0027 High Performance Pulse Train Output (PTO) with PRU-ICSS for Industrial Application combines the AM335x Sitara processor family from Texas Instruments (TI) and the PTO module into a single system-on-chip (SoC) solution. The design is based on the TMDSICE3359 Industrial Communications (...)
TIDEP0032 — 다중 프로토콜 산업용 통신
Industrial Ethernet for industrial automation exists in more than 30 industrial standards. Some of the well-established real-time Ethernet protocols like EtherCAT, EtherNet/IP, PROFINET, Sercos III and PowerLink require dedicated MAC hardware support in terms of FPGA or ASICs. The programmable (...)
TIDEP0054 — 변전소 자동화를 위한 병렬 중복 프로토콜(PRP) 이더넷 레퍼런스 설계
이 레퍼런스 설계는 스마트 그리드 전송 및 배전 네트워크의 변전소 자동화 장비에 안정성이 높고 지연 시간이 낮은 네트워크 통신을 위한 레퍼런스 설계입니다. PRU-ICSS를 사용해 IEC 62439 표준의 PRP(병렬 중복 프로토콜) 사양을 지원합니다. 이 레퍼런스 설계는 FPGA 접근 방식에 대한 저렴한 대안이며, 추가 부품 없이 IEC 61850 지원과 같은 기능을 추가할 수 있는 유연성과 성능을 제공합니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| SOIC (DW) | 16 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.