TCA6408A
- I2C to Parallel port expander
- Operating power-supply voltage range of 1.65 V to 5.5 V
- Allows bidirectional voltage-level translation and gpio expansion between 1.8-V, 2.5-V, 3.3-V, and 5-V I2C bus and P-ports
- Low standby current consumption of 1 µA
- 5-V Tolerant I/O ports
- 400-kHz Fast I2C bus
- Hardware address pin allows two TCA6408A Devices on the same I2C/SMBus bus
- Active-low reset ( RESET) input
- Open-drain active-low interrupt ( INT) output
- Input and output configuration register
- Polarity inversion register
- Internal power-on reset
- Power up with all channels configured as inputs
- No glitch on power up
- Noise filter on SCL and SDA inputs
- Latched outputs with high-current drive maximum capability for directly driving LEDs
- Latch-up performance exceeds 100 mA Per JESD 78, class II
- Schmitt-trigger action allows slow input transition and better switching noise immunity at the SCL and SDA inputs
- ESD Protection exceeds JESD 22
- 2000-V Human body model (A114-A)
- 1000-V Charged-device model (C101)
The TCA6408A is a 16-pin device that provides 8-bits of general purpose parallel input/output (I/O) expansion for the two-line bidirectional I2C bus (or SMBus) protocol. This device can operate with a power supply voltage ranging from 1.65 V to 5.5 V on both the I2C bus side (VCCI) and on the P-port side (VCCP). This allows the TCA6408A to interface with next-generation microprocessors and microcontrollers on the SDA/SCL side, where supply levels are dropping down to conserve power. In contrast to the dropping power supplies of microprocessors and microcontrollers, some PCB components such as LEDs remain at a 5-V power supply.
The device supports both 100-kHz (Standard-mode) and 400-kHz (Fast-mode) clock frequencies. I/O expanders such as the TCA6408A provide a simple solution when additional I/Os are needed for switches, sensors, push-buttons, LEDs, fans, and so forth.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TCA6408A Low-Voltage 8-Bit I2C and SMBus I/O Expander With Interrupt Output, Reset, and Configuration Registers datasheet (Rev. E) | PDF | HTML | 2023. 1. 30 | |
| 애플리케이션 노트 | Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) | PDF | HTML | 2024. 7. 3 | ||
| 애플리케이션 노트 | I2C Dynamic Addressing | 2019. 4. 25 | |||
| 애플리케이션 노트 | Choosing the Correct I2C Device for New Designs | PDF | HTML | 2016. 9. 7 | ||
| 선택 가이드 | I2C Infographic Flyer | 2015. 12. 3 | |||
| 애플리케이션 노트 | Understanding the I2C Bus | PDF | HTML | 2015. 6. 30 | ||
| 애플리케이션 노트 | Maximum Clock Frequency of I2C Bus Using Repeaters | 2015. 5. 15 | |||
| 애플리케이션 노트 | I2C Bus Pull-Up Resistor Calculation | PDF | HTML | 2015. 2. 13 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
AM261-SOM-EVM — AM261x 제어 시스템 온 모듈(SOM) 평가 모듈
IO-EXPANDER-EVM — IO-확장기-EVM: I2C 및 SMBus IO 확장기 평가 모듈
IO 확장기 평가 모듈(EVM)을 사용하면 TI의 SMBus 및 I2C IO 확장기 라인 디바이스 포트폴리오를 평가할 수 있습니다. TCA6424A 및 TCA9539는 보드에 설치됩니다. 24핀 TSSOP 풋프린트는TCA6408A, TCA6416A, TCA9534, TCA9534A, TCA9535, TCA9538, TCA9554, TCA9554A 및 TCA9555를 지원합니다.
SLVC564 — I/O Expander Software and Firmware Package
I2C-DESIGNER — I2C 디자이너 툴
TIDA-00018 — 프로그래머블 로직 컨트롤러(PLC)용 온도 센서 인터페이스 모듈
The TIDA-00018 reference design enables faster development of high precision temperature measurement solutions using 24-Bit delta-sigma ADC and most widely used temperature sensors like thermocouple and RTD. The design guide will address the sensor signal conditioning, thermocouple cold junction (...)
TIDA-00110 — RTD를 사용한 스마트 그리드 애플리케이션의 온도 감지를 위한 AFE(아날로그 프론트 엔드) 레퍼런스 디자인
이 레퍼런스 디자인은 ADC 하나를 통해 최대 4개의 RTD(Resistor Temperature Detector)를 연결하여 소형 모듈식 솔루션을 만들 수 있게 지원합니다. ADC와 프로세서 간의 통신은 SPI 인터페이스를 통해 이루어집니다. 한 애플리케이션에 8개의 RTD가 필요할 경우 이러한 모듈을 최대 하나 더 연결하기만 하면 됩니다. 이 솔루션은 2와이어, 3와이어 또는 4와이어 유형의 RTD를 처리할 수 있는 유연성을 제공합니다.
TIDA-00310 — 스마트 그리드 IED용 아날로그 입력, 출력 및 릴레이 드라이브 출력 모듈 레퍼런스 디자인
이 레퍼런스 디자인은 전압(5V ~ 10V DC) 또는 전류(4-20mA)와 같은 아날로그 IO를 사용하는 그리드의 다른 디바이스와 통신해야 하는 보호 릴레이 및 RTU와 같은 스마트 그리드 디바이스를 위한 유연한 아날로그 IO 솔루션을 제공합니다. 이 솔루션은 유형의 IO와 전원 디지털 릴레이 드라이브를 지원합니다. 이 모듈에서는 프로세서 간 통신을 위해 SPI 및 I2C 통신 인터페이스를 사용할 수 있습니다.
TIDA-00609 — 자동 부팅 오디오 시스템
The purpose of this reference design is to provide hardware and software tools that can be used as reference for audio systems. The new revision of the PurePath™ Console Motherboard (Rev F) adds stand-alone self-booting capabilities to allow making compelling demos with any evaluation module (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| TSSOP (PW) | 16 | Ultra Librarian |
| UQFN (RSV) | 16 | Ultra Librarian |
| VQFN (RGT) | 16 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.