SLUSG35A August   2026  – November 2026 TPS12S24F-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 SPI Timing Requirements
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Power Supply Input
      2. 7.3.2 Charge Pump and Gate Driver Output (VS, GATEx, BSTx, SRCx)
      3. 7.3.3 Driving Capacitive, Resistive and Inductive Loads
        1. 7.3.3.1 Capacitive Load Driving
          1. 7.3.3.1.1 Using SCP Based Auto-Retry Method (GATEx):
          2. 7.3.3.1.2 Using Main Path Gate Slew Rate Control Method (GATEx, SRCx):
            1. 7.3.3.1.2.1 Setting the INRUSH Current
            2. 7.3.3.1.2.2 Sizing CBSTx Capacitor
          3. 7.3.3.1.3 Using PWM Control Method (GATEx)
        2. 7.3.3.2 Resistive or Inductive Load Driving
      4. 7.3.4 Protection Mechanisms
        1. 7.3.4.1 I2T Based Overcurrent and Short-Circuit Protection
          1. 7.3.4.1.1 I2T Accumulation and De-Accumulation for DCR_CHx = '0' Setting
          2. 7.3.4.1.2 I2T Accumulation and De-accumulation for DCR_CHx = '1' Setting
        2. 7.3.4.2 NTC-Based External FET Over-Temperature Protection
        3. 7.3.4.3 Device Junction Overtemperature Warning
        4. 7.3.4.4 Input Undervoltage and Overvoltage Protection
        5. 7.3.4.5 External FET Drain to Source Voltage (VDS) Overvoltage Protection
        6. 7.3.4.6 Bi-VDS Based Short-Circuit Protection
        7. 7.3.4.7 Reverse Polarity Protection
        8. 7.3.4.8 Loss of Ground
      5. 7.3.5 Diagnostic Mechanisms
        1. 7.3.5.1 ADC Sense Signals
        2. 7.3.5.2 Analog and Digital Current Monitor (VIMONx)
        3. 7.3.5.3 Input Supply Voltage Measurement
        4. 7.3.5.4 Output Voltage Measurement
        5. 7.3.5.5 External FET Temperature Measurement
        6. 7.3.5.6 External FET Bi-Directional Drain to Source (Bi-VDS) Measurement
        7. 7.3.5.7 Controller Temperature Measurement
        8. 7.3.5.8 VOUT Short-to-Battery or FET Short and Open-Load Detection
          1. 7.3.5.8.1 Measurement With Main FET (GATEx) Enabled
          2. 7.3.5.8.2 Detection With Main FET (GATEx) Disabled
            1. 7.3.5.8.2.1 Off-State Short-to-Battery Detection
            2. 7.3.5.8.2.2 Off-State Open Load Detection
        9. 7.3.5.9 VOUT Short-to-Battery or FET Short Detection for Power at all Times (PAAT) Loads
      6. 7.3.6 Fault Indication (FLT / WAKE)
        1. 7.3.6.1 FAULT_GLOBAL [15:8] Bits
      7. 7.3.7 Output Disable (OUT_DISx) Function
      8. 7.3.8 Brief Supply Interruptions Behavior
        1. 7.3.8.1 EVENT1
        2. 7.3.8.2 EVENT2
      9. 7.3.9 SPI Mode Operation
        1. 7.3.9.1 SPI
        2. 7.3.9.2 Chip Select (CS)
        3. 7.3.9.3 System Clock (SCLK)
        4. 7.3.9.4 Serial Data In (SDI) and Serial Data Out (SDO)
        5. 7.3.9.5 CRC Error Detection and Checking of Clocks
        6. 7.3.9.6 SPI Frame Format
        7. 7.3.9.7 SPI Watchdog Function
    4. 7.4 Device Functional Modes
      1. 7.4.1 State Diagram
      2. 7.4.2 Power Down
      3. 7.4.3 Sleep Mode
      4. 7.4.4 Config or Active Mode (AM)
      5. 7.4.5 Low Power Mode (LPM)
        1. 7.4.5.1 Automatic Low Power Mode (LPM) to Active Mode (AUTO_LPM_ENTRY = '0')
        2. 7.4.5.2 Automatic Low Power Mode (LPM) to Active Mode to LPM (AUTO LPM) for ECU polling (AUTO_LPM_ENTRY = '1')
          1. 7.4.5.2.1 EVENT1
          2. 7.4.5.2.2 EVENT2
          3. 7.4.5.2.3 EVENT3
      6. 7.4.6 Limphome Mode
    5. 7.5 TPS12S24F-Q1 Pre-Production Silicon Limitations
      1. 7.5.1 SDO Pin Tristate Workaround (Only for Parallel SPI Configuration, not for Daisy-Chain)
  9. 8 Register Maps
    1. 8.1 TPS12S24F-Q1 Registers
    2. 8.2 EEPROM (NVM) Overview
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Driving Power at All Times (PAAT) Loads With Automatic Load Wakeup and Output Bulk Capacitor Charging
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Selection of Main Path MOSFETs
          2. 9.2.1.2.2 Selection of Bootstrap Capacitor, CBSTx
        3. 9.2.1.3 Application Curves
    3. 9.3 System Examples
      1. 9.3.1 TPS12S24F-Q1 System Level Configurations
    4. 9.4 Power Supply Recommendations
      1. 9.4.1 Transient and EMI/EMC Recommendations
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Tape and Reel Information
    2. 12.2 Mechanical Data

TPS12S24F-Q1 Pre-Production Silicon Limitations

Table 7-11 Summary of Pre-Production Silicon Limitations

PARAMETER

TEST CONDITION/EXPLANATION

OBSERVATION IN PRE-PRODUCTION SILICON

EXPECTED BEHAVIOR. TO BE FIXED IN PRODUCTION SILICON

Current sense Accuracy

VSNSx = 6mV,

GAINx setting = 50V/V

VIMONx pin voltage = 243.5mV

ISNS register value: ADC_RESULT_CHx_I = 87

ISNS accuracy is 12%

VIMONx pin voltage = 275mV

ISNS register value: ADC_RESULT_CHx_I = 101

ISNS digital sense accuracy must be (7%).

I2T accuracy directly impact by ISNS accuracy.

SCP in LPM

Output Short to ground in LPM. Bypass FET turn off instantly and main FET turn on

LPM bypass FET Thermal shutdown bit goes ‘1’

LPM_HS_CHx bit remains ‘0’

LPM bypass FET Thermal shutdown remains ‘0’

LPM_HS_CHx bit must go to ‘1’

Functionality is working but wrong indication

WAKE Indication

•

Gate going high within 7.5us after loadwakeup detection but FLT/WAKE pin goes low after 50usec

FLT/WAKE pin goes low after 5usec.

No major impact at system level

GLOBAL_ERR_FLT register read

Observed only after LPM Exit

Working normally in active mode

VBB_UV_WRN = ‘1’

GLOBAL_ERR = ‘1’

VBB_UV_WRN = ‘0’

GLOBAL_ERR = ‘0’

No major impact at the system level.

SDO pin state

CSn pulled low to high

SDO retains LSB of last data value. Cannot support parallel SPI.

SDO must be tri-state when CSn is pulled low to high.

GND Loss Detection

Device GND floating or high slew rate transient (10V/us) lifting GND pin >2V threshold

Gate turns off. Digital gets stuck (SPI Write does not work) because internal oscillator is susceptible to high slew rate on GND which can occur due to poor grounding or hot-swapping

The GATEx must turn off. GATEx must turn on automatically when GND is restored and SPI Write/Read works normally.

Charge pump UVLO

CPUVLO falling threshold

8V. Device can detect CPUVLO during FET turn off if CBSTx is not sized properly.

Should be 6.5V.

Use CBST > 10x [Ciss (external FET) + CGATEx]

FET Short BIST

Run FET short BIST on CH1 and CH2

FET Short BIST indication works only for CH2.

FET Short BIST indication works for CH1 and CH2.
Open load detection Run OL detection on CH1 and CH2 OL detection indication works only for CH2. OL detection indication works for CH1 and CH2.