SLUSG35A August   2026  – November 2026 TPS12S24F-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 SPI Timing Requirements
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Power Supply Input
      2. 7.3.2 Charge Pump and Gate Driver Output (VS, GATEx, BSTx, SRCx)
      3. 7.3.3 Driving Capacitive, Resistive and Inductive Loads
        1. 7.3.3.1 Capacitive Load Driving
          1. 7.3.3.1.1 Using SCP Based Auto-Retry Method (GATEx):
          2. 7.3.3.1.2 Using Main Path Gate Slew Rate Control Method (GATEx, SRCx):
            1. 7.3.3.1.2.1 Setting the INRUSH Current
            2. 7.3.3.1.2.2 Sizing CBSTx Capacitor
          3. 7.3.3.1.3 Using PWM Control Method (GATEx)
        2. 7.3.3.2 Resistive or Inductive Load Driving
      4. 7.3.4 Protection Mechanisms
        1. 7.3.4.1 I2T Based Overcurrent and Short-Circuit Protection
          1. 7.3.4.1.1 I2T Accumulation and De-Accumulation for DCR_CHx = '0' Setting
          2. 7.3.4.1.2 I2T Accumulation and De-accumulation for DCR_CHx = '1' Setting
        2. 7.3.4.2 NTC-Based External FET Over-Temperature Protection
        3. 7.3.4.3 Device Junction Overtemperature Warning
        4. 7.3.4.4 Input Undervoltage and Overvoltage Protection
        5. 7.3.4.5 External FET Drain to Source Voltage (VDS) Overvoltage Protection
        6. 7.3.4.6 Bi-VDS Based Short-Circuit Protection
        7. 7.3.4.7 Reverse Polarity Protection
        8. 7.3.4.8 Loss of Ground
      5. 7.3.5 Diagnostic Mechanisms
        1. 7.3.5.1 ADC Sense Signals
        2. 7.3.5.2 Analog and Digital Current Monitor (VIMONx)
        3. 7.3.5.3 Input Supply Voltage Measurement
        4. 7.3.5.4 Output Voltage Measurement
        5. 7.3.5.5 External FET Temperature Measurement
        6. 7.3.5.6 External FET Bi-Directional Drain to Source (Bi-VDS) Measurement
        7. 7.3.5.7 Controller Temperature Measurement
        8. 7.3.5.8 VOUT Short-to-Battery or FET Short and Open-Load Detection
          1. 7.3.5.8.1 Measurement With Main FET (GATEx) Enabled
          2. 7.3.5.8.2 Detection With Main FET (GATEx) Disabled
            1. 7.3.5.8.2.1 Off-State Short-to-Battery Detection
            2. 7.3.5.8.2.2 Off-State Open Load Detection
        9. 7.3.5.9 VOUT Short-to-Battery or FET Short Detection for Power at all Times (PAAT) Loads
      6. 7.3.6 Fault Indication (FLT / WAKE)
        1. 7.3.6.1 FAULT_GLOBAL [15:8] Bits
      7. 7.3.7 Output Disable (OUT_DISx) Function
      8. 7.3.8 Brief Supply Interruptions Behavior
        1. 7.3.8.1 EVENT1
        2. 7.3.8.2 EVENT2
      9. 7.3.9 SPI Mode Operation
        1. 7.3.9.1 SPI
        2. 7.3.9.2 Chip Select (CS)
        3. 7.3.9.3 System Clock (SCLK)
        4. 7.3.9.4 Serial Data In (SDI) and Serial Data Out (SDO)
        5. 7.3.9.5 CRC Error Detection and Checking of Clocks
        6. 7.3.9.6 SPI Frame Format
        7. 7.3.9.7 SPI Watchdog Function
    4. 7.4 Device Functional Modes
      1. 7.4.1 State Diagram
      2. 7.4.2 Power Down
      3. 7.4.3 Sleep Mode
      4. 7.4.4 Config or Active Mode (AM)
      5. 7.4.5 Low Power Mode (LPM)
        1. 7.4.5.1 Automatic Low Power Mode (LPM) to Active Mode (AUTO_LPM_ENTRY = '0')
        2. 7.4.5.2 Automatic Low Power Mode (LPM) to Active Mode to LPM (AUTO LPM) for ECU polling (AUTO_LPM_ENTRY = '1')
          1. 7.4.5.2.1 EVENT1
          2. 7.4.5.2.2 EVENT2
          3. 7.4.5.2.3 EVENT3
      6. 7.4.6 Limphome Mode
    5. 7.5 TPS12S24F-Q1 Pre-Production Silicon Limitations
      1. 7.5.1 SDO Pin Tristate Workaround (Only for Parallel SPI Configuration, not for Daisy-Chain)
  9. 8 Register Maps
    1. 8.1 TPS12S24F-Q1 Registers
    2. 8.2 EEPROM (NVM) Overview
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Driving Power at All Times (PAAT) Loads With Automatic Load Wakeup and Output Bulk Capacitor Charging
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Selection of Main Path MOSFETs
          2. 9.2.1.2.2 Selection of Bootstrap Capacitor, CBSTx
        3. 9.2.1.3 Application Curves
    3. 9.3 System Examples
      1. 9.3.1 TPS12S24F-Q1 System Level Configurations
    4. 9.4 Power Supply Recommendations
      1. 9.4.1 Transient and EMI/EMC Recommendations
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Tape and Reel Information
    2. 12.2 Mechanical Data

External FET Temperature Measurement

The TPS12SxxF-Q1 senses external FET temperature via NTC resistor and provides a temperature measurement for each of the power MOSFETs through the 10-bit ADC. The FET temperature sense function is disabled by default. To enable the FET temperature sense function for each channel it must be globally enabled in the ADC_CONFIG register through the ADC_TSNS_DIS bit. The conversion equation for the FET temperature measurement is Equation 11. The ADC measurement result is available in the ADC_RESULT_CHx_T register. The TSNS_RDY_CHx bit is set to one if a new ADC conversion result exists since the register is last read.

Equation 11. ADC_RESULT_CHx_T =  1023V(ADC_REF) ×(V(REF_TMP) × RTSNSx)(RNTCx + RTMPx)

Where

  • V(REF_TMP) = 50mV
  • Integrated RTSNSx = 45kΩ for standard 10kΩ NTC and 90kΩ for standard 47kΩ NTC
  • Recommended RTMPx = 700Ω for standard 10kΩ NTC and 1500Ω for standard 47kΩ NTC