SLUSG35A August   2026  â€“ November 2026 TPS12S24F-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 SPI Timing Requirements
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Power Supply Input
      2. 7.3.2 Charge Pump and Gate Driver Output (VS, GATEx, BSTx, SRCx)
      3. 7.3.3 Driving Capacitive, Resistive and Inductive Loads
        1. 7.3.3.1 Capacitive Load Driving
          1. 7.3.3.1.1 Using SCP Based Auto-Retry Method (GATEx):
          2. 7.3.3.1.2 Using Main Path Gate Slew Rate Control Method (GATEx, SRCx):
            1. 7.3.3.1.2.1 Setting the INRUSH Current
            2. 7.3.3.1.2.2 Sizing CBSTx Capacitor
          3. 7.3.3.1.3 Using PWM Control Method (GATEx)
        2. 7.3.3.2 Resistive or Inductive Load Driving
      4. 7.3.4 Protection Mechanisms
        1. 7.3.4.1 I2T Based Overcurrent and Short-Circuit Protection
          1. 7.3.4.1.1 I2T Accumulation and De-Accumulation for DCR_CHx = '0' Setting
          2. 7.3.4.1.2 I2T Accumulation and De-accumulation for DCR_CHx = '1' Setting
        2. 7.3.4.2 NTC-Based External FET Over-Temperature Protection
        3. 7.3.4.3 Device Junction Overtemperature Warning
        4. 7.3.4.4 Input Undervoltage and Overvoltage Protection
        5. 7.3.4.5 External FET Drain to Source Voltage (VDS) Overvoltage Protection
        6. 7.3.4.6 Bi-VDS Based Short-Circuit Protection
        7. 7.3.4.7 Reverse Polarity Protection
        8. 7.3.4.8 Loss of Ground
      5. 7.3.5 Diagnostic Mechanisms
        1. 7.3.5.1 ADC Sense Signals
        2. 7.3.5.2 Analog and Digital Current Monitor (VIMONx)
        3. 7.3.5.3 Input Supply Voltage Measurement
        4. 7.3.5.4 Output Voltage Measurement
        5. 7.3.5.5 External FET Temperature Measurement
        6. 7.3.5.6 External FET Bi-Directional Drain to Source (Bi-VDS) Measurement
        7. 7.3.5.7 Controller Temperature Measurement
        8. 7.3.5.8 VOUT Short-to-Battery or FET Short and Open-Load Detection
          1. 7.3.5.8.1 Measurement With Main FET (GATEx) Enabled
          2. 7.3.5.8.2 Detection With Main FET (GATEx) Disabled
            1. 7.3.5.8.2.1 Off-State Short-to-Battery Detection
            2. 7.3.5.8.2.2 Off-State Open Load Detection
        9. 7.3.5.9 VOUT Short-to-Battery or FET Short Detection for Power at all Times (PAAT) Loads
      6. 7.3.6 Fault Indication (FLT / WAKE)
        1. 7.3.6.1 FAULT_GLOBAL [15:8] Bits
      7. 7.3.7 Output Disable (OUT_DISx) Function
      8. 7.3.8 Brief Supply Interruptions Behavior
        1. 7.3.8.1 EVENT1
        2. 7.3.8.2 EVENT2
      9. 7.3.9 SPI Mode Operation
        1. 7.3.9.1 SPI
        2. 7.3.9.2 Chip Select (CS)
        3. 7.3.9.3 System Clock (SCLK)
        4. 7.3.9.4 Serial Data In (SDI) and Serial Data Out (SDO)
        5. 7.3.9.5 CRC Error Detection and Checking of Clocks
        6. 7.3.9.6 SPI Frame Format
        7. 7.3.9.7 SPI Watchdog Function
    4. 7.4 Device Functional Modes
      1. 7.4.1 State Diagram
      2. 7.4.2 Power Down
      3. 7.4.3 Sleep Mode
      4. 7.4.4 Config or Active Mode (AM)
      5. 7.4.5 Low Power Mode (LPM)
        1. 7.4.5.1 Automatic Low Power Mode (LPM) to Active Mode (AUTO_LPM_ENTRY = '0')
        2. 7.4.5.2 Automatic Low Power Mode (LPM) to Active Mode to LPM (AUTO LPM) for ECU polling (AUTO_LPM_ENTRY = '1')
          1. 7.4.5.2.1 EVENT1
          2. 7.4.5.2.2 EVENT2
          3. 7.4.5.2.3 EVENT3
      6. 7.4.6 Limphome Mode
    5. 7.5 TPS12S24F-Q1 Pre-Production Silicon Limitations
      1. 7.5.1 SDO Pin Tristate Workaround (Only for Parallel SPI Configuration, not for Daisy-Chain)
  9. 8 Register Maps
    1. 8.1 TPS12S24F-Q1 Registers
    2. 8.2 EEPROM (NVM) Overview
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Driving Power at All Times (PAAT) Loads With Automatic Load Wakeup and Output Bulk Capacitor Charging
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Selection of Main Path MOSFETs
          2. 9.2.1.2.2 Selection of Bootstrap Capacitor, CBSTx
        3. 9.2.1.3 Application Curves
    3. 9.3 System Examples
      1. 9.3.1 TPS12S24F-Q1 System Level Configurations
    4. 9.4 Power Supply Recommendations
      1. 9.4.1 Transient and EMI/EMC Recommendations
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Tape and Reel Information
    2. 12.2 Mechanical Data

Driving Capacitive, Resistive and Inductive Loads

All off-board loads have different type. Each load profile interacts differently with the Smart High Side Switch or Controller and require different considerations to specify robust protection. Whether the load is resistive, capacitive, inductive, or does not fall neatly into one of those categories such as LEDs changes how driving the load must be approached and designed. The user must understand what load profile is expected, and then understand how that impacts the design of the output stage.

Table 7-1 Load Driving Using TPS12SxxF-Q1
TYPE OF LOADLOAD DRIVING METHODREGISTER SETTING
Capacitive Load, CAP_CHRG_CHx = 0x0, 0x1 or 0x3Using Short-circuit protection (SCP) based auto-retry method

CAP_CHRG_CHx = 0x0

INRUSH_DURATION_CHx = 0x0 to 0x7 (used only for VOUT_ERR_CHx indication)

FWD_SCP_SET_CHx = 0x0 to 0xF

AUTO_RETRY_DURATION_CHx = 0x0 to 0x3

LATCH_CHx = 0x0

FOLDBACK_LOCK_DIS_CHx = 0x1

Using main path gate slew control

CAP_CHRG_CHx = 0x1

INRUSH_DURATION_CHx = 0x0 to 0x7 (used only for VOUT_ERR_CHx indication)

Using main path PWM mode

CAP_CHRG_CHx = 0x3, PWM_DTY_CHx = 0x00 to 0xFF and PWM_FREQ_CHx = 0x0 to 0xF

INRUSH_DURATION_CHx = 0x0 to 0x7

Resistive or Inductive LoadUsing main path PWM method

CAP_CHRG_CHx = 0x0

PWM_EN_CHx = 0x1, PWM_DTY_CHx = 0x00 to 0xFF to and PWM_FREQ_CHx = 0x0 to 0xF