SNLS800 October   2026 DP83TC1103-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1. 5.1 Pin Power Domain
    2. 5.2 Pin States
    3. 5.3 Pin Multiplexing
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Timing Diagrams
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 IEEE802.1AS Features
        1. 7.3.1.1 PTP Clock Configuration
          1. 7.3.1.1.1 PTP Reference Clock
          2. 7.3.1.1.2 PTP Synchronized Clock (Wall Clock)
            1. 7.3.1.1.2.1 PTP Time Read or Write
            2. 7.3.1.1.2.2 PTP Clock Initialization
            3. 7.3.1.1.2.3 PTP Clock Adjustment
          3. 7.3.1.1.3 PTP Time Registers
        2. 7.3.1.2 Packet Timestamps
          1. 7.3.1.2.1 Transmit (Egress) Packet Parser and Timestamp
          2. 7.3.1.2.2 Receive (ingress) Packet Parser and Timestamp
          3. 7.3.1.2.3 PTP Transmit and Receive Timestamp Registers
        3. 7.3.1.3 Event Triggering and Timestamping
          1. 7.3.1.3.1 Event Triggering (Output)
            1. 7.3.1.3.1.1 Trigger Initialization
          2. 7.3.1.3.2 Event Timestamp (Input)
            1. 7.3.1.3.2.1 Timestamp Storage and Reading
          3. 7.3.1.3.3 Event Capture and Output Trigger Registers
        4. 7.3.1.4 PTP Interrupts
        5. 7.3.1.5 PTP I/O Configuration
      2. 7.3.2 TC10 Sleep Wake-up
        1. 7.3.2.1 Functions of the PHY for TC10 Support
          1. 7.3.2.1.1 Transition from Sleep to Wake-up Mode
            1. 7.3.2.1.1.1 Local Wake Detection
            2. 7.3.2.1.1.2 WUP Transmission and Reception
          2. 7.3.2.1.2 Wake Forwarding
          3. 7.3.2.1.3 Transition to Sleep - Sleep Negotiation
            1. 7.3.2.1.3.1 Sleep Ack
            2. 7.3.2.1.3.2 Sleep Request
            3. 7.3.2.1.3.3 Sleep Silent
            4. 7.3.2.1.3.4 Sleep Fail
            5. 7.3.2.1.3.5 Sleep
            6. 7.3.2.1.3.6 Force Sleep
        2. 7.3.2.2 Power Supply Networks for Sleep Applications
        3. 7.3.2.3 Configuration for Non-TC10 Applications
        4. 7.3.2.4 Miscellaneous Sleep Features
        5. 7.3.2.5 Fast Wake-up
      3. 7.3.3 PPM Monitor
      4. 7.3.4 Clock Dithering
      5. 7.3.5 Output Slew Control
      6. 7.3.6 Diagnostic Tool Kit
        1. 7.3.6.1 Signal Quality Indicator
        2. 7.3.6.2 Electrostatic Discharge Sensing
        3. 7.3.6.3 Time Domain Reflectometry
      7. 7.3.7 BIST and Loopback Modes
        1. 7.3.7.1 Data Generator and Checker
        2. 7.3.7.2 xMII Loopback
        3. 7.3.7.3 PCS Loopback
        4. 7.3.7.4 Digital Loopback
        5. 7.3.7.5 Analog Loopback
        6. 7.3.7.6 Reverse Loopback
      8. 7.3.8 Compliance Test Modes
        1. 7.3.8.1 Test Mode 1
        2. 7.3.8.2 Test Mode 2
        3. 7.3.8.3 Test Mode 4
        4. 7.3.8.4 Test Mode 5
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power Modes
        1. 7.4.1.1 Power Down
        2. 7.4.1.2 Reset
        3. 7.4.1.3 Standby
        4. 7.4.1.4 Normal
        5. 7.4.1.5 Sleep
      2. 7.4.2 Media Dependent Interface
        1. 7.4.2.1 100BASE-T1 Leader and 100BASE-T1 Follower Configuration
        2. 7.4.2.2 Auto-Polarity Detection and Correction
        3. 7.4.2.3 Jabber Detection
        4. 7.4.2.4 Interleave Detection
      3. 7.4.3 MAC Interfaces
        1. 7.4.3.1 Media Independent Interface
        2. 7.4.3.2 Reduced Media Independent Interface
        3. 7.4.3.3 Reduced Gigabit Media Independent Interface
        4. 7.4.3.4 Serial Gigabit Media Independent Interface
      4. 7.4.4 Serial Management Interface
        1. 7.4.4.1 Extended Register Space Access
        2. 7.4.4.2 Write Operation (No Post Increment)
        3. 7.4.4.3 Read Operation (No Post Increment)
        4. 7.4.4.4 Write Operation (Post Increment)
        5. 7.4.4.5 Read Operation (Post Increment)
    5. 7.5 Programming
      1. 7.5.1 Strap Configuration
        1. 7.5.1.1 LED Configuration
  9. 8 DP83TC1103 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Physical Medium Attachment
          1. 9.2.1.1.1 Common-Mode Choke Recommendations
      2. 9.2.2 Detailed Design Procedure
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Signal Traces
        2. 9.4.1.2 Return Path
        3. 9.4.1.3 Metal Pour
        4. 9.4.1.4 PCB Layer Stacking
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

DP83TC1103 Registers

Table 8-1 lists the memory-mapped registers for the DP83TC1103 registers. All register offset addresses not listed in Table 8-1 should be considered as reserved locations and the register contents should not be modified.

Table 8-1 DP83TC1103 Registers
OffsetAcronymRegister NameSection
0x0BMCRIEEE Control RegisterSection 8.1
0x1BMSRIEEE Status RegisterSection 8.2
0x2PHYIDR1PHY Identification Register - 1Section 8.3
0x3PHYIDR2PHY Identification Register - 2Section 8.4
0x10PHYSTSPHY Status RegisterSection 8.5
0x11PHYSCRSoftware Control RegisterSection 8.6
0x12MISR1Interrupt Register -1Section 8.7
0x13MISR2Interrupt Register -2Section 8.8
0x15RECRRX Error Count RegisterSection 8.9
0x16BISCRBIST Control RegisterSection 8.10
0x17MISR4Interrupt Register -4Section 8.11
0x18MISR3Interrupt Register -3Section 8.12
0x19REG_19PHY Address Status RegisterSection 8.13
0x1AREG_1AReceive Symbol Status RegisterSection 8.14
0x1BTC10_ABORT_REGTC10 Abort RegisterSection 8.15
0x1ECDCRTDR Run Status RegisterSection 8.16
0x1FPHYRCRReset Control RegisterSection 8.17
0x3ERegister_3ERegister_3ESection 8.18
0x133Register_133CnS Status RegisterSection 8.19
0x17FRegister_17FWUR WUP Configuration RegisterSection 8.20
0x181Register_181LPS Received Count RegisterSection 8.21
0x182Register_182WUR Received Count RegisterSection 8.22
0x184LPS_CFGLow Power Configuration Register - 0Section 8.23
0x18BLPS_CFG2Low Power Configuration Register - 2Section 8.24
0x18CLPS_CFG3Low Power Configuration Register - 3Section 8.25
0x18DLINK_FAIL_CNTLink Fail Count RegisterSection 8.26
0x18ELPS_STATUSLow Power Status RegisterSection 8.27
0x1A0PCFPHY Control Frame Configuration RegisterSection 8.28
0x1A2MISC1SA DA Configuration RegisterSection 8.29
0x1A3PPM0PPM Monitor Config Register - 0Section 8.30
0x1A4PPM1PPM Monitor Config Register - 1Section 8.31
0x1A5PPM2PPM Monitor Config Register - 2Section 8.32
0x1A6PPM3PPM Monitor Config Register - 3Section 8.33
0x1A7PPM4PPM Monitor Config Register - 4Section 8.34
0x1A8PPM5PPM Monitor Config Register - 5Section 8.35
0x1A9PPM6PPM Monitor Config Register - 6Section 8.36
0x1AAPPM7PPM Monitor Config Register - 7Section 8.37
0x1ADPPM10PPM Monitor Config Register - 10Section 8.38
0x1AEPPM11PPM Monitor Config Register - 11Section 8.39
0x1AFPPM12PPM Monitor Config Register - 12Section 8.40
0x1BEfwu_reg_3Fast Wake Up Register - 3Section 8.41
0x1D2spare_reg_tc10Fast Wake Up Spare RegisterSection 8.42
0x310TDR_TC1TDR Status RegisterSection 8.43
0x402ANA_LD_CTRL_3VDDIO Level Status RegisterSection 8.44
0x430A2D_REG_48RGMII ID Control RegisterSection 8.45
0x440A2D_REG_64ESD Event Count Register - 0Section 8.46
0x442A2D_REG_66ESD Event Count Register - 1Section 8.47
0x444A2D_REG_68TC10 Force Control RegisterSection 8.48
0x450LEDS_CFG_1LED Configuration Register - 1Section 8.49
0x451LEDS_CFG_2LED Configuration Register - 2Section 8.50
0x452IO_MUX_CFG_1IO Multiplexing Register - 1Section 8.51
0x453IO_MUX_CFG_2IO Multiplexing Register - 2Section 8.52
0x456IO_MUX_CFGxMII Impedance Control RegisterSection 8.53
0x45DCHIP_SOR_1Strap Status RegisterSection 8.54
0x45FLED1_ANA_CTRLLED_1 Control RegisterSection 8.55
0x461IMPEDANCE_CTRL_1Impedance Control Register - 1Section 8.56
0x4EELINKUP_TIMER_1Link Up Timer Register - 1Section 8.57
0x4EFLINKUP_TIMER_2Link Up Timer Register - 2Section 8.58
0x523TX_PR_FILT_CTRLMDI Transmit Force RegisterSection 8.59
0x551PG_REG_1CRS_DV Control RegisterSection 8.60
0x552PG_REG_3PG_REG_3Section 8.61
0x553PG_REG_4Auto-Polarity Correction Control RegisterSection 8.62
0x561TC1_LINK_FAIL_LOSSTC1 Link Fail Count RegisterSection 8.63
0x562TC1_LINK_TRAINING_TIMETC1 Link Training Time RegisterSection 8.64
0x563NO_LINK_THNo Link Interrupt TimeThreshold RegisterSection 8.65
0x5A0DITH_CTRL_0Dithering Control Register - 0Section 8.66
0x5A1DITH_CTRL_1Dithering Control Register - 1Section 8.67
0x5A8DITH_RFI_EN_CTRLDithering Enable RegisterSection 8.68
0x5B2CFG_PCF_DMAC_ADDRConfigurable Last Two Bytes of PCF DMACSection 8.69
0x5B7SPARE_IN_FROM_DIG_SL_1Register With Configurable Bits For AnalogSection 8.70
0x5B8CONTROL_REG_1LED_GPIO Enable RegisterSection 8.71
0x600RGMII_CTRLRGMII Control RegisterSection 8.72
0x601RGMII_FIFO_STATUSRGMII FIFO Status RegisterSection 8.73
0x602RGMII_CLK_SHIFT_CTRLRGMII Shift Control RegisterSection 8.74
0x608SGMII_CTRL_1SGMII Control Register - 1Section 8.75
0x60ASGMII_STATUSSGMII Status RegisterSection 8.76
0x60CSGMII_CTRL_2SGMII Control Register - 2Section 8.77
0x60DSGMII_FIFO_STATUSSGMII FIFO Status RegisterSection 8.78
0x618PRBS_STATUS_1PRBS Status Register - 1Section 8.79
0x619PRBS_CTRL_1PRBS Control Register - 1Section 8.80
0x61APRBS_CTRL_2PRBS Control Register - 2Section 8.81
0x61BPRBS_CTRL_3PRBS Control Register - 3Section 8.82
0x61CPRBS_STATUS_2PRBS Status Register - 2Section 8.83
0x61DPRBS_STATUS_3PRBS Status Register - 3Section 8.84
0x61EPRBS_STATUS_4PRBS Status Register - 4Section 8.85
0x620PRBS_STATUS_5PRBS Status Register - 5Section 8.86
0x622PRBS_STATUS_6PRBS Status Register - 6Section 8.87
0x623PRBS_STATUS_7PRBS Status Register - 7Section 8.88
0x624PRBS_CTRL_4PRBS Control Register - 4Section 8.89
0x625PATTERN_CTRL_1BIST Pattern Control Register - 1Section 8.90
0x626PATTERN_CTRL_2BIST Pattern Control Register - 2Section 8.91
0x627PATTERN_CTRL_3BIST Pattern Control Register - 3Section 8.92
0x628PMATCH_CTRL_1BIST Match Control Register - 1Section 8.93
0x629PMATCH_CTRL_2BIST Match Control Register - 2Section 8.94
0x62APMATCH_CTRL_3BIST Match Control Register - 3Section 8.95
0x638PKT_CRC_STATBIST CRC Status RegisterSection 8.96
0x639TX_PKT_CNT_1xMII TX Packet Count Register - 1Section 8.97
0x63ATX_PKT_CNT_2xMII TX Packet Count Register - 2Section 8.98
0x63BTX_PKT_CNT_3xMII TX Packet Count Register - 3Section 8.99
0x63CRX_PKT_CNT_1xMII RX Packet Count Register - 1Section 8.100
0x63DRX_PKT_CNT_2xMII RX Packet Count Register - 2Section 8.101
0x63ERX_PKT_CNT_3xMII RX Packet Count Register - 3Section 8.102
0x648RMII_CTRL_1RMII Control RegisterSection 8.103
0x649RMII_STATUS_1RMII FIFO Status RegisterSection 8.104
0xD00PTP_CTLPTP Control RegisterSection 8.105
0xD01PTP_TDRPTP Time Data RegisterSection 8.106
0xD02PTP_STSPTP Status RegisterSection 8.107
0xD03PTP_TSTSPTP Trigger Status RegisterSection 8.108
0xD04PTP_RATELPTP Rate Low RegisterSection 8.109
0xD05PTP_RATEHPTP Rate High RegisterSection 8.110
0xD08PTP_TXTSPTP Transmit Timestamp RegisterSection 8.111
0xD09PTP_RXTSPTP Receive Timestamp RegisterSection 8.112
0xD0APTP_ESTSPTP Event Status RegisterSection 8.113
0xD10PTP_TRIGPTP Trigger Configuration RegisterSection 8.114
0xD11PTP_EVNTPTP Event Configuration RegisterSection 8.115
0xD12PTP_TXCFG0PTP Transmit Configuration Register 0Section 8.116
0xD13PTP_TXCFG1PTP Transmit Configuration Register 1Section 8.117
0xD14PSF_CFG0PHY Status Frame Configuration Register 0Section 8.118
0xD15PTP_RXCFG0PTP Receive Configuration Register 0Section 8.119
0xD16PTP_RXCFG1PTP Receive Configuration Register 1Section 8.120
0xD17PTP_RXCFG2PTP Receive Configuration Register 2Section 8.121
0xD18PTP_RXCFG3PTP Receive Configuration Register 3Section 8.122
0xD19PTP_RXCFG4PTP Receive Configuration Register 4Section 8.123
0xD1APTP_TRDLPTP Temporary Rate Duration Low RegisterSection 8.124
0xD1BPTP_TRDHPTP Temporary Rate Duration High RegisterSection 8.125
0xD1CPTP_EVNT_TSU_CFGEvent Timestamp Storage ConfigurationSection 8.126
0xD1DPSF_TRIG_TS_ENTrigger Timestamp PHY Status Frame EnableSection 8.127
0xD20PTP_COCPTP Clock Output Control RegisterSection 8.128
0xD21PSF_CFG1Phy Status Frame Configuration Register 1Section 8.129
0xD22PSF_CFG2Phy Status Frame Configuration Register 2Section 8.130
0xD23PSF_CFG3Phy Status Frame Configuration Register 3Section 8.131
0xD24PSF_CFG4Phy Status Frame Configuration Register 4Section 8.132
0xD26PTP_INTCTLPTP Interrupt Control RegisterSection 8.133
0xD27PTP_CLKSRCPTP Clock Source RegisterSection 8.134
0xD28PTP_ETYPEPTP Ethernet Type RegisterSection 8.135
0xD29PTP_OFFPTP Offset RegisterSection 8.136
0xD2BPTP_RXHASHPTP Receive Hash RegisterSection 8.137
0xD30PTP_EVENT_GPIO_SELPTP Event GPIO selectionSection 8.138
0xD32TX_SMD_GPIO_CTLTX path SMD detection and GPIO controlSection 8.139
0xD33SCH_CTL_1Scheduler control 1Section 8.140
0xD34SCH_CTL_2Scheduler control 2Section 8.141
0xD35FREQ_CTL_1Base frequency control 1Section 8.142
0xD36FREQ_CTL_2Base frequency control 2Section 8.143
0xD37PTP_RATEL_ACC_ONLYPTP Rate ACC only LSB RegisterSection 8.144
0xD38PTP_RATEH_ACC_ONLYPTP Rate ACC only MSB Register and enableSection 8.145
0xD39PTP_PLL_CTLPTP_PLL control registerSection 8.146
0xD3APTP_PLL_RD_1PTP timestamp read register 1Section 8.147
0xD3BPTP_PLL_RD_2PTP timestamp read register 2Section 8.148
0xD3CPTP_PLL_RD_3PTP timestamp read register 3Section 8.149
0xD3DPTP_PLL_RD_4PTP timestamp read register 4Section 8.150
0xD3EPTP_PLL_RD_5PTP timestamp read register 5Section 8.151
0xD3FPTP_PLL_RD_6PTP timestamp read register 6Section 8.152
0xD40PTP_ONESTEP_OFFPTP ONESTEP OFFSET registerSection 8.153
0xD45PTP_PSF_VLAN_CFG_1PSF VLAN Configuration 1Section 8.154
0xD46PTP_PSF_VLAN_CFG_2PSF VLAN Configuration 2Section 8.155
0xD47PTP_PSF_VLAN_CFG_3PSF VLAN Configuration 3Section 8.156
0xD48MAX_IPV4_LENGTHPSF IPv4 Packet LengthSection 8.157
0xD49PTP_TXCFG_2PTP Domain Filter ControlsSection 8.158
0xD4APSF_DMAC_1PSF DMAC Address 1Section 8.159
0xD4BPSF_DMAC_2PSF DMAC Address 2Section 8.160
0xD4CPSF_DMAC_3PSF DMAC Address 3Section 8.161
0xD4DPSF_SMAC_1PSF SMAC Address 1Section 8.162
0xD4EPSF_SMAC_2PSF SMAC Address 2Section 8.163
0xD4FPSF_SMAC_3PSF SMAC Address 3Section 8.164
0xD50PSF_ETYPEPSF Ether TypeSection 8.165
0xD51IPV4_DA_1PSF Destination Address 1Section 8.166
0xD52IPV4_DA_2PSF Destination Address 2Section 8.167
0xD53PSF_SOURCE_UDP_PORTPSF UDP Source Port AddressSection 8.168
0xD54PSF_DESTINATION_UDP_PORTPSF UDP Destination Port AddressSection 8.169
0xDE0PTP_LAT_COMP_CTRLPTP Latency Compensation ControlSection 8.170
0xDF0PTP_DEBUG_SELPTP Debug SelectSection 8.171
0x1000MMD1_PMA_CTRL_1PMA Control 1Section 8.172
0x1001MMD1_PMA_STATUS_1PMA Status 1Section 8.173
0x1007MMD1_PMA_STAUS_2PMA Status 2Section 8.174
0x100BMMD1_PMA_EXT_ABILITY_1PMA Extended 1Section 8.175
0x1012MMD1_PMA_EXT_ABILITY_2PMA Extended 2Section 8.176
0x1834MMD1_PMA_CTRL_2PMA Control 2Section 8.177
0x1836MMD1_PMA_TEST_MODE_CTRLPMA TestSection 8.178
0x3000MMD3_PCS_CTRL_1PCS ControlSection 8.179
0x3001MMD3_PCS_Status_1PCS StatusSection 8.180

Complex bit access types are encoded to fit into small table cells. Table 8-2 shows the codes that are used for access types in this section.

Table 8-2 DP83TC1103 Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
R-0R
-0
Read
Returns 0s
RCR
C
Read
to Clear
RHR
H
Read
Set or cleared by hardware
Write Type
WWWrite
W1SW
1S
Write
1 to set
WSCWWrite
Reset or Default Value
-nValue after reset or the default value

8.1 BMCR Register (Offset = 0x0) [Reset = 0x2100]

BMCR is shown in Figure 8-1 and described in Table 8-3.

Return to the Summary Table.

Figure 8-1 BMCR Register
15141312111098
MII ResetMII Loopback EnableSpeed SelectAuto-Negotiation EnableIEEE Power Down EnableMAC Isolate EnableRESERVEDDuplex Mode Select
R-0/W1S-0x0R/W-0x0R-0x1R-0x0R/W-0x0R/W-0x0R-0x0R-0x1
76543210
RESERVEDRESERVED
R-0x0R-0x0
Table 8-3 BMCR Register Field Descriptions
BitFieldTypeResetDescription
15MII ResetR-0/W1S0x0 1b = Digital in reset and all MII regs (0x0 - 0xF) reset to default
0b = No reset
This bit is auto-cleared
14MII Loopback EnableR/W0x0 1b = Enable MII loopback
0b = Disable MII loopback
When xMII loopback mode is activated, the transmitted data presented on xMII TXD is looped back to xMII RXD internally.
There is no LINK indication generated when xMII loopback is enabled.
13Speed SelectR0x1 Speed Selection: Always 100-Mbps Speed
12Auto-Negotiation EnableR0x0 Auto-Negotiation: Not supported on this device
11IEEE Power Down EnableR/W0x0 This bit can be programmed to enter and exit IEEE power down mode
This bit provide status when using INT_N as power down pin
1b = Power down mode
0b = Normal mode
10MAC Isolate EnableR/W0x0 1b = Isolate mode (No output from PHY to MAC)
0b = Normal mode
9RESERVEDR0x0Reserved
8Duplex Mode SelectR0x1 1b = Full duplex
0b = Half duplex
7RESERVEDR0x0Reserved
6:0RESERVEDR0x0Reserved

8.2 BMSR Register (Offset = 0x1) [Reset = 0x0061]

BMSR is shown in Figure 8-2 and described in Table 8-4.

Return to the Summary Table.

Figure 8-2 BMSR Register
15141312111098
100Base-T4 Support100Base-X Full Duplex Support100Base-X Half Duplex Support10 Mbps Full Duplex Support10 Mbps Half Duplex SupportRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDSMI Preamble SuppressionRESERVEDRESERVEDAuto-Negotiation AbilityLink Status (Latch Low)Jabber detectExtended register Capability
R-0x0R-0x1R-0x1R-0x0R-0x0RH-0x0RC-0x0R-0x1
Table 8-4 BMSR Register Field Descriptions
BitFieldTypeResetDescription
15100Base-T4 SupportR0x0 0b = PHY does not support 100BASE-T4
14100Base-X Full Duplex SupportR0x0 0b = PHY does not support full duplex 100BASE-X
13100Base-X Half Duplex SupportR0x0 0b = PHY does not support half duplex 100BASE-X
1210 Mbps Full Duplex SupportR0x0 0b = PHY does not support 10 Mb/s in full duplex mode
1110 Mbps Half Duplex SupportR0x0 0b = PHY does not support 10 Mb/s in half duplex mode
10:7RESERVEDR0x0Reserved
6SMI Preamble SuppressionR0x1 1b = PHY accepts management frames with preamble suppressed.
0b = PHY does not accept management frames with preamble suppressed
5RESERVEDR0x1Reserved
4RESERVEDR0x0Reserved
3Auto-Negotiation AbilityR0x0 0b = PHY does not Auto-Negotiation
1Jabber detectRC0x0 1b = Jabber condition detected
0b = No Jabber condition detected
0Extended register CapabilityR0x1 1b = Extended register capabilities
0b = Basic register set capabilities only

8.3 PHYIDR1 Register (Offset = 0x2) [Reset = 0x2000]

PHYIDR1 is shown in Figure 8-3 and described in Table 8-5.

Return to the Summary Table.

Figure 8-3 PHYIDR1 Register
15141312111098
Organizationally Unique Identifier 1
R-0x2000
76543210
Organizationally Unique Identifier 1
R-0x2000
Table 8-5 PHYIDR1 Register Field Descriptions
BitFieldTypeResetDescription
15:0Organizationally Unique Identifier 1R0x2000 Unique Identifier for the part

8.4 PHYIDR2 Register (Offset = 0x3) [Reset = 0xA2F0]

PHYIDR2 is shown in Figure 8-4 and described in Table 8-6.

Return to the Summary Table.

Figure 8-4 PHYIDR2 Register
15141312111098
Unique Identifier 2Model Number
R-0x28R-0x2F
76543210
Model NumberRevision Number
R-0x2FR-0x0
Table 8-6 PHYIDR2 Register Field Descriptions
BitFieldTypeResetDescription
15:10Unique Identifier 2R0x28 Unique Identifier for the part
9:4Model NumberR0x2F Unique Identifier for the part
3:0Revision NumberR0x0 Unique Identifier for the part

8.5 PHYSTS Register (Offset = 0x10) [Reset = 0x0004]

PHYSTS is shown in Figure 8-5 and described in Table 8-7.

Return to the Summary Table.

Figure 8-5 PHYSTS Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDDescrambler Lock Status (Latch Low)RESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0RH-0x0R-0x0
76543210
Interrupt Pin StatusRESERVEDRESERVEDRESERVEDMII Loopback StatusDuplex Mode StatusRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x1R-0x0R-0x0
Table 8-7 PHYSTS Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11RESERVEDR0x0Reserved
10RESERVEDR0x0Reserved
9Descrambler Lock Status (Latch Low)RH0x0 1b = Descrambler is locked
0b = Descrambler is unlocked at least once
8RESERVEDR0x0Reserved
7Interrupt Pin StatusR0x0 Interrupts pin status, cleared on reading 0x12
1b = Interrupts pin not set
0b = Interrupt pin had been set
6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3MII Loopback StatusR0x0 1b = MII loopback enabled
0b = MII loopback Disabled
2Duplex Mode StatusR0x1 1b = Full duplex
0b = Half duplex
1RESERVEDR0x0Reserved
0RESERVEDR0x0Reserved

8.6 PHYSCR Register (Offset = 0x11) [Reset = 0x010B]

PHYSCR is shown in Figure 8-6 and described in Table 8-8.

Return to the Summary Table.

Figure 8-6 PHYSCR Register
15141312111098
RESERVEDRESERVEDRESERVEDSGMII Soft ResetMAC Isolate for PHY_ADDR 0x00RMII TX FIFO Depth
R-0x0R-0x0R-0x0R/WSC-0x0R/W-0x0R/W-0x1
76543210
RESERVEDRESERVEDInterrupt PolarityForce InterruptInterrupts EnableInterrupt Pin Configuration
R-0x0R-0x0R/W-0x1R/W-0x0R/W-0x1R/W-0x1
Table 8-8 PHYSCR Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13:12RESERVEDR0x0Reserved
11SGMII Soft ResetR/WSC0x0 SGMII Digital Reset
This bit is auto-cleared
10MAC Isolate for PHY_ADDR 0x00R/W0x0 MAC Isolate is enabled only if PHY address is 0x00
Reg0x0[10] works for all PHY addresses including 0x00
1b = Isolate mode (No output from PHY to MAC)
0b = Normal mode
9:8RMII TX FIFO DepthR/W0x1 00b = 4 nibbles
01b = 5 nibbles
10b = 6 nibbles
11b = 8 nibbles
7RESERVEDR0x0Reserved
6:4RESERVEDR0x0Reserved
3Interrupt PolarityR/W0x1 1b = Active low
0b = Active high
2Force InterruptR/W0x0 1b = Force interrupt pin
1Interrupts EnableR/W0x1 1b = Enable interrupts
0b = Disable interrupts
0Interrupt Pin ConfigurationR/W0x1 1b = Configure INT_N pin is as interrupt output pin
0b = Configure INT_N pin as power down input pin

8.7 MISR1 Register (Offset = 0x12) [Reset = 0x0000]

MISR1 is shown in Figure 8-7 and described in Table 8-9.

Return to the Summary Table.

Figure 8-7 MISR1 Register
15141312111098
RESERVEDEnergy Detect Change StatusLink Status Change StatusWake on LAN StatusESD Fault Detected StatusTraining Done StatusRESERVEDRX Error Counter Half Full Status
R-0x0RC-0x0RC-0x0RC-0x0RC-0x0RC-0x0R-0x0RC-0x0
76543210
RESERVEDEnergy Detect Change IndicationLink Status Change IndicationWake on LAN IndicationESD Fault Detected IndicationTraining Done IndicationRESERVEDRX Error Counter Half Full Indication
R-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R-0x0R/W-0x0
Table 8-9 MISR1 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14Energy Detect Change StatusRC0x0 Status is changed to 1 when there is a change of MDI Energy detection output
Status is cleared on read of this register
12Wake on LAN StatusRC0x0 Status is changed to 1 when WOL is received
Status is cleared on read of this register
11ESD Fault Detected StatusRC0x0 Status is changed to 1 when ESD fault is detected
Status is cleared on read of this register
10Training Done StatusRC0x0 Status is changed to 1 when training is done
Status is cleared on read of this register
9RESERVEDR0x0Reserved
8RX Error Counter Half Full StatusRC0x0 Status is changed to 1 when RX Error Counter in 0x15 is half full
Status is cleared on read of this register
7RESERVEDR0x0Reserved
6Energy Detect Change IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
4Wake on LAN IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
3ESD Fault Detected IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
2Training Done IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
1RESERVEDR0x0Reserved
0RX Error Counter Half Full IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled

8.8 MISR2 Register (Offset = 0x13) [Reset = 0x0000]

MISR2 is shown in Figure 8-8 and described in Table 8-10.

Return to the Summary Table.

Figure 8-8 MISR2 Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDData Polarity Change StatusJabber Detect Status
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0RC-0x0RC-0x0
76543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDData Polarity Change IndicationJabber Detect Indication
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R/W-0x0R/W-0x0
Table 8-10 MISR2 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11RESERVEDR0x0Reserved
10RESERVEDR0x0Reserved
9Data Polarity Change StatusRC0x0 Status is changed to 1 when MDI lines polarity change is detected
Status is cleared on read of this register
8Jabber Detect StatusRC0x0 Status is changed to 1 when jabber is detected
Status is cleared on read of this register
7RESERVEDR0x0Reserved
6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3RESERVEDR0x0Reserved
2RESERVEDR0x0Reserved
1Data Polarity Change IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
0Jabber Detect IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled

8.9 RECR Register (Offset = 0x15) [Reset = 0x0000]

RECR is shown in Figure 8-9 and described in Table 8-11.

Return to the Summary Table.

Figure 8-9 RECR Register
15141312111098
RX Error Count
RC-0x0
76543210
RX Error Count
RC-0x0
Table 8-11 RECR Register Field Descriptions
BitFieldTypeResetDescription
15:0RX Error CountRC0x0 RX_ER Counter:
When a valid carrier is presented (only while RX_DV is set), and there is at least one occurrence of an invalid data symbol, this 16-bit counter increments for each receive error detected. The RX_ER counter does not count in xMII loopback mode. The counter stops when it reaches its maximum count (0xFFFF).
When the counter exceeds half-full (0x7FFF), an interrupt is generated.
This register is cleared on read.

8.10 BISCR Register (Offset = 0x16) [Reset = 0x0100]

BISCR is shown in Figure 8-10 and described in Table 8-12.

Return to the Summary Table.

Figure 8-10 BISCR Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x1
76543210
RESERVEDData Transmission to MDI in xMII LoopbackLoopback ModePCS Loopback EnableRESERVED
R-0x0R/W-0x0R/W-0x0R/W-0x0R-0x0
Table 8-12 BISCR Register Field Descriptions
BitFieldTypeResetDescription
15:11RESERVEDR0x0Reserved
10RESERVEDR0x0Reserved
9RESERVEDR0x0Reserved
8RESERVEDR0x1Reserved
7RESERVEDR0x0Reserved
6Data Transmission to MDI in xMII LoopbackR/W0x0 0b = Suppress data to MDI during xMII loopback
1b = Transmit data to MDI during xMII loopback
5:2Loopback ModeR/W0x0 Enable Loopbacks other than PCS loopback. 0x16[1] should be 0
0001b = Digital Loopback
0010b = Analog Loopback
0100b = Reverse Loopback
1000b = External Loopback
1PCS Loopback EnableR/W0x0 0b = Disable PCS Loopback
1b = Enable PCS Loopback
0RESERVEDR0x0Reserved

8.11 MISR4 Register (Offset = 0x17) [Reset = 0x0000]

MISR4 is shown in Figure 8-11 and described in Table 8-13.

Return to the Summary Table.

Figure 8-11 MISR4 Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDPPM Monitor Unlock StatusRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVEDRESERVEDPPM Monitor Unlock IndicationRESERVED
R-0x0R-0x0R-0x0R-0x0R/W-0x0R-0x0
Table 8-13 MISR4 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11PPM Monitor Unlock StatusR0x0 Status is changed to 1 when PPM Monitor unlocks
Status is cleared on read of this register
10:7RESERVEDR0x0Reserved
6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3PPM Monitor Unlock IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
2:0RESERVEDR0x0Reserved

8.12 MISR3 Register (Offset = 0x18) [Reset = 0x0035]

MISR3 is shown in Figure 8-12 and described in Table 8-14.

Return to the Summary Table.

Figure 8-12 MISR3 Register
15141312111098
RESERVEDNo Link StatusSleep Fail StatusPower-On Reset Done StatusNo Frame StatusWUR Received StatusRemote Wake-up IndicationLPS Received Status
R-0x0RC-0x0RC-0x0RC-0x0RC-0x0RC-0x0RC-0x0RC-0x0
76543210
RESERVEDNo Link IndicationSleep Fail IndicationPower-On Reset Done IndicationNo Frame IndicationWUR Received IndicationRESERVEDLPS Received Indication
R-0x0R/W-0x0R/W-0x1R/W-0x1R/W-0x0R/W-0x1R-0x0R/W-0x1
Table 8-14 MISR3 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
13Sleep Fail StatusRC0x0 Status is changed to 1 when Sleep Negotiation Fails
Status is cleared on read of this register
12Power-On Reset Done StatusRC0x0 Status is changed to 1 Power-On Reset is done after the supplies are up
Status is cleared on read of this register
11No Frame StatusRC0x0 Status is changed to 1 when No frame is detected until
Status is cleared on read of this register
10WUR Received StatusRC0x0 Status is changed to 1 when WUR command is received from link partner
Status is cleared on read of this register
9Remote Wake-up IndicationRC0x0 Status is 1 after power-up if device is woken-up remotely
Status is cleared on read of this register
8LPS Received StatusRC0x0 Status is changed to 1 when LPS command is received from link partner
Status is cleared on read of this register
7RESERVEDR0x0Reserved
5Sleep Fail IndicationR/W0x1 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
4Power-On Reset Done IndicationR/W0x1 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
3No Frame IndicationR/W0x0 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
2WUR Received IndicationR/W0x1 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled
1RESERVEDR0x0Reserved
0LPS Received IndicationR/W0x1 1b = Enable indication on INT_N pin if corresponding Interrupt Status is set
0b = Indication is Disabled

8.13 REG_19 Register (Offset = 0x19) [Reset = 0x0800]

REG_19 is shown in Figure 8-13 and described in Table 8-15.

Return to the Summary Table.

Figure 8-13 REG_19 Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x1R-0x0R-0x0
76543210
RESERVEDPHY Address
R-0x0R-0x0
Table 8-15 REG_19 Register Field Descriptions
BitFieldTypeResetDescription
15:14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11RESERVEDR0x1Reserved
10RESERVEDR0x0Reserved
9:5RESERVEDR0x0Reserved
4:0PHY AddressR0x0 PHY Address latched from straps

8.14 REG_1A Register (Offset = 0x1A) [Reset = 0x0000]

REG_1A is shown in Figure 8-14 and described in Table 8-16.

Return to the Summary Table.

Figure 8-14 REG_1A Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDData Polarity StatusRESERVEDJabber Detect Disable
R-0x0R-0x0R-0x0R/W-0x0
Table 8-16 REG_1A Register Field Descriptions
BitFieldTypeResetDescription
15:5RESERVEDR0x0Reserved
4Data Polarity StatusR0x0 0b = Normal Polarity
1b = Reverse Polarity
3:1RESERVEDR0x0Reserved
0Jabber Detect DisableR/W0x0 0b = Jabber detection is enabled
1b =Jabber detection is Disabled

8.15 TC10_ABORT_REG Register (Offset = 0x1B) [Reset = 0x0000]

TC10_ABORT_REG is shown in Figure 8-15 and described in Table 8-17.

Return to the Summary Table.

Figure 8-15 TC10_ABORT_REG Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDSleep Abort through GPIOSleep Abort
R-0x0R/W-0x0R/W-0x0
Table 8-17 TC10_ABORT_REG Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0x0Reserved
1Sleep Abort through GPIOR/W0x0 Sleep can be aborted by driving high on GPIO
1b = Use GPIO_1 for Sleep Abort
0b = GPIO is not used for Sleep Abort
0Sleep AbortR/W0x0 This bit to be set 1 to abort the sleep
Cleared on transition to normal mode

8.16 CDCR Register (Offset = 0x1E) [Reset = 0x0000]

CDCR is shown in Figure 8-16 and described in Table 8-18.

Return to the Summary Table.

Figure 8-16 CDCR Register
15141312111098
TDR StartTDR Auto-Run EnableRESERVED
RH/W1S-0x0R/W-0x0R-0x0
76543210
RESERVEDTDR Done StatusTDR Fail status
R-0x0R-0x0R-0x0
Table 8-18 CDCR Register Field Descriptions
BitFieldTypeResetDescription
15TDR StartRH/W1S0x0 1b = Start TDR
Bit is cleared after TDR run is complete
14TDR Auto-Run EnableR/W0x0 1b = Start TDR automatically on link down
0b = Start TDR manually using 0x1E[15]
13:2RESERVEDR0x0Reserved
1TDR Done StatusR0x0 1b = TDR done
0b = TDR on-going or not initiated
0TDR Fail statusR0x0 When TDR Done Status is 1, this bit indicates if TDR ran successfully
1b = TDR run failed
0b = TDR ran successfully

8.17 PHYRCR Register (Offset = 0x1F) [Reset = 0x0000]

PHYRCR is shown in Figure 8-17 and described in Table 8-19.

Return to the Summary Table.

Figure 8-17 PHYRCR Register
15141312111098
Hard ResetSoft ResetSoft Reset 2RESERVEDRESERVED
R-0/W1S-0x0R-0/W1S-0x0R-0/W1S-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x0
Table 8-19 PHYRCR Register Field Descriptions
BitFieldTypeResetDescription
15Hard ResetR-0/W1S0x0 Resets Digital Core and register File
This bet is self clearing
14Soft ResetR-0/W1S0x0 Resets Digital Core but register File is not reset
This bit is self clearing
13Soft Reset 2R-0/W1S0x0 Resets register File
This bit is self clearing
12RESERVEDR0x0Reserved
11:7RESERVEDR0x0Reserved
6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4:0RESERVEDR0x0Reserved

8.18 Register_3E (Offset = 0x3E) [Reset = 0x0000]

Register_3E is shown in Figure 8-18 and described in Table 8-20.

Return to the Summary Table.

Figure 8-18 Register_3E
15141312111098
RESERVED
R-0x0
76543210
RESERVEDcfg_leader_scr_rst_on_dsp_failcfg_follower_scr_rst_on_dsp_failRESERVEDRESERVEDRESERVEDRESERVED
R-0x0R/W-0x0R/W-0x0R-0x0R-0x0R-0x0R-0x0
Table 8-20 Register_3E Field Descriptions
BitFieldTypeResetDescription
15:6RESERVEDR0x0Reserved
5cfg_leader_scr_rst_on_dsp_failR/W0x0 Enable Reset of scrambler on DSP fallback when phy is configured as Leader
4cfg_follower_scr_rst_on_dsp_failR/W0x0 Enable Reset of scrambler on DSP fallback when phy is configured as Follower
3RESERVEDR0x0Reserved
2RESERVEDR0x0Reserved
1RESERVEDR0x0Reserved
0RESERVEDR0x0Reserved

8.19 Register_133 (Offset = 0x133) [Reset = 0x0000]

Register_133 is shown in Figure 8-19 and described in Table 8-21.

Return to the Summary Table.

Figure 8-19 Register_133
15141312111098
RESERVEDLink Up StatusPHY Control In Send Data ModeLink StatusRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDDescrambler Lock StatusLocal Receiver StatusRemote Receiver Status
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
Table 8-21 Register_133 Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
11:8RESERVEDR0x0Reserved
7RESERVEDR0x0Reserved
6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3RESERVEDR0x0Reserved
2Descrambler Lock StatusR0x0 Descrambler lock status
1Local Receiver StatusR0x0 Local receiver status
0Remote Receiver StatusR0x0 Remote receiver status

8.20 Register_17F (Offset = 0x17F) [Reset = 0x4028]

Register_17F is shown in Figure 8-20 and described in Table 8-22.

Return to the Summary Table.

Figure 8-20 Register_17F
15141312111098
WUR from WAKE pinWUP EnableRESERVED
R/W-0x0R/W-0x1R-0x0
76543210
Wake Pulse Threshold
R/W-0x28
Table 8-22 Register_17F Field Descriptions
BitFieldTypeResetDescription
15WUR from WAKE pinR/W0x0 Enable WUR transmission when a pulse is transmitted on WAKE pin
1b = Enable sending WUR
Threshold of WAKE pulse width can be configured through 0x17F[7:0]
14WUP EnableR/W0x1 Enable WUP transmission after local wake
1b = WUP transmission is enabled
0b = WUP transmission is Disabled
This option can be effectively used when PHY powers-up in Standby mode through strap
13:8RESERVEDR0x0Reserved
7:0Wake Pulse ThresholdR/W0x28 Width of WAKE pulse in microseconds required to initiate WUR during an active link

8.21 Register_181 (Offset = 0x181) [Reset = 0x0000]

Register_181 is shown in Figure 8-21 and described in Table 8-23.

Return to the Summary Table.

Figure 8-21 Register_181
15141312111098
RESERVEDRX LPS Count
R-0x0R-0x0
76543210
RX LPS Count
R-0x0
Table 8-23 Register_181 Field Descriptions
BitFieldTypeResetDescription
15:10RESERVEDR0x0Reserved
9:0RX LPS CountR0x0 Indicates number of LPS codes received

8.22 Register_182 (Offset = 0x182) [Reset = 0x0000]

Register_182 is shown in Figure 8-22 and described in Table 8-24.

Return to the Summary Table.

Figure 8-22 Register_182
15141312111098
RESERVEDRX WUR Count
R-0x0R-0x0
76543210
RX WUR Count
R-0x0
Table 8-24 Register_182 Field Descriptions
BitFieldTypeResetDescription
15:10RESERVEDR0x0Reserved
9:0RX WUR CountR0x0 Indicates number of WUR codes received

8.23 LPS_CFG Register (Offset = 0x184) [Reset = 0x0203]

LPS_CFG is shown in Figure 8-23 and described in Table 8-25.

Return to the Summary Table.

Figure 8-23 LPS_CFG Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x1R-0x0
76543210
RESERVEDRESERVEDRESERVEDWake Forward ForceWake Forward Pulse WidthWake Forward EnableRESERVED
R-0x0R-0x0R-0x0R/W-0x0R/W-0x0R/W-0x1R-0x1
Table 8-25 LPS_CFG Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14:13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11:10RESERVEDR0x0Reserved
9RESERVEDR0x1Reserved
8:7RESERVEDR0x0Reserved
6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4Wake Forward ForceR/W0x0 1b = Force pulse on WAKE pin
Pulse Width is configurable by bits [3:2]
The bit is self-cleared
3:2Wake Forward Pulse WidthR/W0x0 Configures the pulse width on WAKE pin for wake-forwarding
00b = 50us
01b = 500us
10b = 2ms
11b = 20ms
1Wake Forward EnableR/W0x1 Enable Wake Forwarding on WAKE pin on reception of WUR Command
0b = Enable Wake forwarding
1b = Disable Wake forwarding
0RESERVEDR0x1Reserved

8.24 LPS_CFG2 Register (Offset = 0x18B) [Reset = 0x1C4B]

LPS_CFG2 is shown in Figure 8-24 and described in Table 8-26.

Return to the Summary Table.

Figure 8-24 LPS_CFG2 Register
15141312111098
RESERVEDRESERVEDRESERVEDStop Sleep Negotiation on Link DownStop Sleep Negotiation on ActivityRESERVEDRESERVEDTC10 Disable
R-0x0R-0x0R-0x0R/W-0x1R/W-0x1R-0x1R-0x0R/W-0x0
76543210
RESERVEDAutonomous ModeTransition To StandbyRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R-0x0R/W-0x1R/W-0x0R-0x0R-0x1R-0x0R-0x1R-0x1
Table 8-26 LPS_CFG2 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12Stop Sleep Negotiation on Link DownR/W0x1 1b = Stop Sleep Negotiation if link goes down during negotiation
11Stop Sleep Negotiation on ActivityR/W0x1 1b = Stop Sleep Negotiation when activity from MAC is observed in SLEEP_ACK state
10RESERVEDR0x1Reserved
9RESERVEDR0x0Reserved
8TC10 DisableR/W0x0 0b = Enable TC10
1b = Disable TC10
Default value is decided by RX_CLK strap
7RESERVEDR0x0Reserved
6Autonomous ModeR/W0x1 1b = PHY entered normal mode on power up
0b = PHY entered standby mode on power up
Default value is decided by LED_1 strap
This bit is cleared post link up.
5Transition To StandbyR/W0x0 1b = Enable normal to standby transition on over temperature/over voltage/under voltage
0b = Disable normal to standby transition on over temperature/over voltage/under voltage
4RESERVEDR0x0Reserved
3RESERVEDR0x1Reserved
2RESERVEDR0x0Reserved
1RESERVEDR0x1Reserved
0RESERVEDR0x1Reserved

8.25 LPS_CFG3 Register (Offset = 0x18C) [Reset = 0x0000]

LPS_CFG3 is shown in Figure 8-25 and described in Table 8-27.

Return to the Summary Table.

Figure 8-25 LPS_CFG3 Register
15141312111098
RESERVEDPower State Entry
R-0x0RH/W1S-0x0
76543210
Power State Entry
RH/W1S-0x0
Table 8-27 LPS_CFG3 Register Field Descriptions
BitFieldTypeResetDescription
15:9RESERVEDR0x0Reserved
8:0Power State EntryRH/W1S0x0 00000001b = Normal command
00000010b = Sleep request
00010000b = Standby command
10000000b = WUR command

8.27 LPS_STATUS Register (Offset = 0x18E) [Reset = 0x0000]

LPS_STATUS is shown in Figure 8-27 and described in Table 8-29.

Return to the Summary Table.

Figure 8-27 LPS_STATUS Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDPower State Status
R-0x0R-0x0
Table 8-29 LPS_STATUS Register Field Descriptions
BitFieldTypeResetDescription
15:7RESERVEDR0x0Reserved
6:0Power State StatusR0x0 00000001b = Sleep Mode
00000010b = Standby Mode
00000100b = Normal Mode
00001000b = Sleep Ack
00010000b = Sleep Req
00100000b = Sleep Fail
01000000b = Sleep Silent

8.28 PCF Register (Offset = 0x1A0) [Reset = 0x0000]

PCF is shown in Figure 8-28 and described in Table 8-30.

Return to the Summary Table.

Figure 8-28 PCF Register
15141312111098
RESERVEDPHY Control Frames Error StatusPHY Control Frames Ok StatusRESERVEDPHY Control Frames Destination Address
R-0x0R-0x0R-0x0R-0x0R/W-0x0
76543210
PHY Control Frames InterruptPHY Control Frames Broadcast DisablePHY Control Frames Buffer SizePHY Control Frames Enable
R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-30 PCF Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14PHY Control Frames Error StatusR0x0 Indicates an error was detected in a PCF Frame since the last read of this register. This bit is cleared on read.
13PHY Control Frames Ok StatusR0x0 Indicates a PCF Frame has completed without error since the last read of this register. This bit is cleared on read.
12:9RESERVEDR0x0Reserved
8PHY Control Frames Destination AddressR/W0x0 Select MAC Destination Address for Phy Control Frames:
0: Use Mac Address [08 00 17 0B 6B 0F]
1: Use Mac Address [08 00 17 00 00 00]
The device also recognizes packets with the above address with the Multicast bit set (that is 09 00 17)
7:6PHY Control Frames InterruptR/W0x0 PCF Interrupt Control and Status:
Bit 7 - Enable indication of PCF Frame Error Status on INT_N pin
Bit 6 - Enable indication of PCF Frame OK Status on INT_N pin
Status is available in 0x1A0[14:13]
5PHY Control Frames Broadcast DisableR/W0x0 By default, the device accepts broadcast Phy Control Frames which have a Phy address field of 0x1F. If this bit is set to a 1, the Phy Control Frame must have a Phy Address field that exactly matches the device Phy Address.
4:1PHY Control Frames Buffer SizeR/W0x0 Determines the buffer size for transmit to allow Phy Control Frame detection. All packets are delayed as they pass through this buffer. If set to 0, packets are not be delayed and Phy Control frames are truncated after the Destination Address field
0PHY Control Frames EnableR/W0x0 Enables register writes using Phy Control Frames

8.29 MISC1 Register (Offset = 0x1A2) [Reset = 0x0002]

MISC1 is shown in Figure 8-29 and described in Table 8-31.

Return to the Summary Table.

Figure 8-29 MISC1 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDSwap DA SARESERVEDRESERVEDRESERVED
R-0x0R/W-0x0R-0x0R-0x0R-0x2
Table 8-31 MISC1 Register Field Descriptions
BitFieldTypeResetDescription
15:7RESERVEDR0x0Reserved
6Swap DA SAR/W0x0 1b = Swap Destination Address and Source Address fields of the packet for debug
5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3:0RESERVEDR0x2Reserved

8.30 PPM0 Register (Offset = 0x1A3) [Reset = 0xF423]

PPM0 is shown in Figure 8-30 and described in Table 8-32.

Return to the Summary Table.

Figure 8-30 PPM0 Register
15141312111098
Monitor Clock Count [15:0]
R/W-0xF423
76543210
Monitor Clock Count [15:0]
R/W-0xF423
Table 8-32 PPM0 Register Field Descriptions
BitFieldTypeResetDescription
15:0Monitor Clock Count [15:0]R/W0xF423 Lower 16 bits of Monitor clock counter in PPM Monitor
Monitor Clock Count = Refresh period/monitor clock period
Refresh period can be any common multiple of monitor and reference clock periods

8.31 PPM1 Register (Offset = 0x1A4) [Reset = 0x0000]

PPM1 is shown in Figure 8-31 and described in Table 8-33.

Return to the Summary Table.

Figure 8-31 PPM1 Register
15141312111098
Monitor Clock Count [31:16]
R/W-0x0
76543210
Monitor Clock Count [31:16]
R/W-0x0
Table 8-33 PPM1 Register Field Descriptions
BitFieldTypeResetDescription
15:0Monitor Clock Count [31:16]R/W0x0 Higher 16 bits of Monitor clock counter in PPM Monitor
Monitor Clock Count = Refresh period/monitor clock period
Refresh period can be any common multiple of monitor and reference clock periods

8.32 PPM2 Register (Offset = 0x1A5) [Reset = 0x30D3]

PPM2 is shown in Figure 8-32 and described in Table 8-34.

Return to the Summary Table.

Figure 8-32 PPM2 Register
15141312111098
Reference Clock Count [15:0]
R/W-0x30D3
76543210
Reference Clock Count [15:0]
R/W-0x30D3
Table 8-34 PPM2 Register Field Descriptions
BitFieldTypeResetDescription
15:0Reference Clock Count [15:0]R/W0x30D3 Lower 16 bits of Reference clock counter in PPM Monitor
Reference Clock Count = Refresh period/reference clock period
Refresh period can be any common multiple of monitor and reference clock periods

8.33 PPM3 Register (Offset = 0x1A6) [Reset = 0x0000]

PPM3 is shown in Figure 8-33 and described in Table 8-35.

Return to the Summary Table.

Figure 8-33 PPM3 Register
15141312111098
Reference Clock Count [31:16]
R/W-0x0
76543210
Reference Clock Count [31:16]
R/W-0x0
Table 8-35 PPM3 Register Field Descriptions
BitFieldTypeResetDescription
15:0Reference Clock Count [31:16]R/W0x0 Higher 16 bits of Reference clock counter in PPM Monitor
Reference Clock Count = Refresh period/reference clock period
Refresh period can be any common multiple of monitor and reference clock periods

8.34 PPM4 Register (Offset = 0x1A7) [Reset = 0x0000]

PPM4 is shown in Figure 8-34 and described in Table 8-36.

Return to the Summary Table.

Figure 8-34 PPM4 Register
15141312111098
PPM Monitor Interrupt Threshold Count - 1 [15:0]
R/W-0x0
76543210
PPM Monitor Interrupt Threshold Count - 1 [15:0]
R/W-0x0
Table 8-36 PPM4 Register Field Descriptions
BitFieldTypeResetDescription
15:0PPM Monitor Interrupt Threshold Count - 1 [15:0]R/W0x0 Lower 16 bits of PPM Monitor Interrupt Threshold Count - 1:
PPM Monitor Interrupt Threshold Count
1 = Monitor Clock Count
PPM beyond which interrupt should be flagged

8.35 PPM5 Register (Offset = 0x1A8) [Reset = 0x0000]

PPM5 is shown in Figure 8-35 and described in Table 8-37.

Return to the Summary Table.

Figure 8-35 PPM5 Register
15141312111098
PPM Monitor Interrupt Threshold Count - 1 [31:16]
R/W-0x0
76543210
PPM Monitor Interrupt Threshold Count - 1 [31:16]
R/W-0x0
Table 8-37 PPM5 Register Field Descriptions
BitFieldTypeResetDescription
15:0PPM Monitor Interrupt Threshold Count - 1 [31:16]R/W0x0 Higher 16 bits of PPM Monitor Interrupt Threshold Count -1:
PPM Monitor Interrupt Threshold Count
1 = Monitor Clock Count
PPM beyond which interrupt should be flagged

8.36 PPM6 Register (Offset = 0x1A9) [Reset = 0x0000]

PPM6 is shown in Figure 8-36 and described in Table 8-38.

Return to the Summary Table.

Figure 8-36 PPM6 Register
15141312111098
PPM Monitor Interrupt Threshold Count - 2 [15:0]
R/W-0x0
76543210
PPM Monitor Interrupt Threshold Count - 2 [15:0]
R/W-0x0
Table 8-38 PPM6 Register Field Descriptions
BitFieldTypeResetDescription
15:0PPM Monitor Interrupt Threshold Count - 2 [15:0]R/W0x0 Lower 16 bits of PPM Monitor Interrupt Threshold Count - 2:
PPM Monitor Interrupt Threshold Count
2 = Monitor clock count - (Monitor Clock Count
negative PPM beyond which interrupt should be flagged)

8.37 PPM7 Register (Offset = 0x1AA) [Reset = 0x0000]

PPM7 is shown in Figure 8-37 and described in Table 8-39.

Return to the Summary Table.

Figure 8-37 PPM7 Register
15141312111098
PPM Monitor Interrupt Threshold Count - 2 [31:16]
R/W-0x0
76543210
PPM Monitor Interrupt Threshold Count - 2 [31:16]
R/W-0x0
Table 8-39 PPM7 Register Field Descriptions
BitFieldTypeResetDescription
15:0PPM Monitor Interrupt Threshold Count - 2 [31:16]R/W0x0 Higher 16 bits of PPM Monitor Interrupt Threshold Count -2:
PPM Monitor Interrupt Threshold Count
2 = Monitor clock count - (Monitor Clock Count
negative PPM beyond which interrupt should be flagged)

8.38 PPM10 Register (Offset = 0x1AD) [Reset = 0x0000]

PPM10 is shown in Figure 8-38 and described in Table 8-40.

Return to the Summary Table.

Figure 8-38 PPM10 Register
15141312111098
PPM Monitor Output [15:0]
R/W-0x0
76543210
PPM Monitor Output [15:0]
R/W-0x0
Table 8-40 PPM10 Register Field Descriptions
BitFieldTypeResetDescription
15:0PPM Monitor Output [15:0]R/W0x0 PPM Monitor output
If 0x01AE[15] = 0, ppm offset is negative, if 0x01AE[15] = 1, ppm offset is positive
PPM offset of monitor clock = {0x01AE[14:0],0x01AD[15:0]}/ {0x01A4, 0x01A3}

8.39 PPM11 Register (Offset = 0x1AE) [Reset = 0x0000]

PPM11 is shown in Figure 8-39 and described in Table 8-41.

Return to the Summary Table.

Figure 8-39 PPM11 Register
15141312111098
PPM Monitor Output [31:16]
R/W-0x0
76543210
PPM Monitor Output [31:16]
R/W-0x0
Table 8-41 PPM11 Register Field Descriptions
BitFieldTypeResetDescription
15:0PPM Monitor Output [31:16]R/W0x0 PPM Monitor output
If 0x01AE[15] = 0, ppm offset is negative, if 0x01AE[15] = 1, ppm offset is positive
PPM offset of monitor clock = {0x01AE[14:0],0x01AD[15:0]}/ {0x01A4, 0x01A3}

8.40 PPM12 Register (Offset = 0x1AF) [Reset = 0x0000]

PPM12 is shown in Figure 8-40 and described in Table 8-42.

Return to the Summary Table.

Figure 8-40 PPM12 Register
15141312111098
PPM Monitor External Clock SelectPPM Monitor EnableReference Clock Select for PPM MonitorMonitor Clock Select for PPM Monitor
R/W-0x0R/W-0x0R/W-0x0R/W-0x0
76543210
Monitor Clock Select for PPM MonitorLatch PPM Monitor ValueRESERVEDRESERVED
R/W-0x0R/W-0x0R-0x0R-0x0
Table 8-42 PPM12 Register Field Descriptions
BitFieldTypeResetDescription
15:14PPM Monitor External Clock SelectR/W0x0 Selects GPIO pin for External Clock Input of PPM Monitor:
  • 0x2 = LED_0
13PPM Monitor EnableR/W0x0 Enable for PPM monitor:
  • 0x0 = Disable PPM Monitor
  • 0x1 = Enable PPM Monitor
12:9Reference Clock Select for PPM MonitorR/W0x0 Selects the reference clock for the PPM monitor
  • 0x0 = XI Input
  • 0x1 = 200MHz Recovered Clock
  • 0x2 = PLL CLK of 250MHz
  • 0x3 = PTP PLL
  • 0x4 = External Clock Input
  • 0x5 = 200MHz Leader Transmit Clock
  • 0x6 = SGMII Recovered Clock
  • 0x7 = PTP Trigger 0
8:5Monitor Clock Select for PPM MonitorR/W0x0 Selects the monitor clock for the PPM monitor
  • 0x0 = XI Input
  • 0x1 = 200MHz Recovered Clock
  • 0x2 = PLL CLK of 250Mhz
  • 0x3 = PTP PLL
  • 0x4 = External Clock Input
  • 0x5 = 200MHz Leader Transmit Clock
  • 0x6 = SGMII Recovered Clock
  • 0x7 = PTP Trigger 0
4Latch PPM Monitor ValueR/W0x0 Latches the ppm monitor value to a shadow register
  • 0x0 = Disable PPM Status Read
  • 0x1 = Enable PPM Status Read
3:2RESERVEDR0x0Reserved
1:0RESERVEDR0x0Reserved

8.41 fwu_reg_3 Register (Offset = 0x1BE) [Reset = 0x0158]

fwu_reg_3 is shown in Figure 8-41 and described in Table 8-43.

Return to the Summary Table.

Figure 8-41 fwu_reg_3 Register
15141312111098
RESERVEDRESERVEDFast Wake-Up Memory Load EnableFast Wake-Up Load TriggerFast Wake-Up Memory Reset
R-0x0R-0x0R/W-0x0R/W-0x0R/W-0x1
76543210
RESERVEDRESERVED
R-0x16R-0x0
Table 8-43 fwu_reg_3 Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11RESERVEDR0x0Reserved
10Fast Wake-Up Memory Load EnableR/W0x0 Program this bit to 1 to enable loading register address and data into the memory
9Fast Wake-Up Load TriggerR/W0x0 Program this bit to 1 after programming register Address and Data in 0x1BC and 0x1BD
This bit is auto-clearing
8Fast Wake-Up Memory ResetR/W0x1
  • 0x0 = Reset Memory
7:2RESERVEDR0x16Reserved
1:0RESERVEDR0x0Reserved

8.42 spare_reg_tc10 Register (Offset = 0x1D2) [Reset = 0x0000]

spare_reg_tc10 is shown in Figure 8-42 and described in Table 8-44.

Return to the Summary Table.

Figure 8-42 spare_reg_tc10 Register
15141312111098
Configure Fast Wake-Up
R/W-0x0
76543210
Configure Fast Wake-Up
R/W-0x0
Table 8-44 spare_reg_tc10 Register Field Descriptions
BitFieldTypeResetDescription
15:0Configure Fast Wake-UpR/W0x0 To enable fast wake-up Memory program
0x01D2 = 0x0004
0x01D2 = 0x0014
0x01D2 = 0x0004

8.43 TDR_TC1 Register (Offset = 0x310) [Reset = 0x0000]

TDR_TC1 is shown in Figure 8-43 and described in Table 8-45.

Return to the Summary Table.

Figure 8-43 TDR_TC1 Register
15141312111098
RESERVEDRESERVED
R-0x0R-0x0
76543210
Fault Detect StatusFault TypeTDR Fault Location
R-0x0R-0x0R-0x0
Table 8-45 TDR_TC1 Register Field Descriptions
BitFieldTypeResetDescription
15:9RESERVEDR0x0Reserved
8RESERVEDR0x0Reserved
7Fault Detect StatusR0x0 1b = Fault detected in cable
0b = No Fault detected in cable
6Fault TypeR0x0 0b = Short to GND, supply, or between MDI pins
1b = Open. Applicable to both 1-wire and 2-wire open faults
5:0TDR Fault LocationR0x0 Fault location in meters (Valid only if Fault Detect Status = 1)

8.44 ANA_LD_CTRL_3 Register (Offset = 0x402) [Reset = 0x0000]

ANA_LD_CTRL_3 is shown in Figure 8-44 and described in Table 8-46.

Return to the Summary Table.

Figure 8-44 ANA_LD_CTRL_3 Register
15141312111098
VDDIO Supply LevelRESERVEDRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0
Table 8-46 ANA_LD_CTRL_3 Register Field Descriptions
BitFieldTypeResetDescription
15:14VDDIO Supply LevelR0x0 VDDIO Level Detected by the PHY:
00b = 1.8V VDDIO
01b = 2.5V VDDIO
11b = 3.3V VDDIO
13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11:10RESERVEDR0x0Reserved
9:8RESERVEDR0x0Reserved
7:4RESERVEDR0x0Reserved
3RESERVEDR0x0Reserved
2:0RESERVEDR0x0Reserved

8.45 A2D_REG_48 Register (Offset = 0x430) [Reset = 0x0AA0]

A2D_REG_48 is shown in Figure 8-45 and described in Table 8-47.

Return to the Summary Table.

Figure 8-45 A2D_REG_48 Register
15141312111098
RESERVEDRESERVEDRGMII TX Shift Delay
R-0x0R-0x0R/W-0xA
76543210
RGMII RX Shift DelayRESERVED
R/W-0xAR-0x0
Table 8-47 A2D_REG_48 Register Field Descriptions
BitFieldTypeResetDescription
15:13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11:8RGMII TX Shift DelayR/W0xA Controls Internal Delay in RGMII mode in Steps of 312.5ps
Delay = ((Bit[7:4] in decimal) + 1) x 312.5 ps
7:4RGMII RX Shift DelayR/W0xA Controls Internal Delay in RGMII mode in Steps of 312.5ps
Delay = ((Bit[7:4] in decimal) + 1) x 312.5 ps
3:0RESERVEDR0x0Reserved

8.46 A2D_REG_64 Register (Offset = 0x440) [Reset = 0x0001]

A2D_REG_64 is shown in Figure 8-46 and described in Table 8-48.

Return to the Summary Table.

Figure 8-46 A2D_REG_64 Register
15141312111098
RESERVEDRESERVED
R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDESD Event Counter Disable
R-0x0R-0x0R-0x0R-0x0R-0x0R/W-0x1
Table 8-48 A2D_REG_64 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14:5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3RESERVEDR0x0Reserved
2RESERVEDR0x0Reserved
1RESERVEDR0x0Reserved
0ESD Event Counter DisableR/W0x1 1b = Disable ESD Counter
0b = Enable ESD Counter
Toggle this bit to clear the ESD counter

8.47 A2D_REG_66 Register (Offset = 0x442) [Reset = 0x0000]

A2D_REG_66 is shown in Figure 8-47 and described in Table 8-49.

Return to the Summary Table.

Figure 8-47 A2D_REG_66 Register
15141312111098
RESERVEDESD Event CountRESERVED
R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0
Table 8-49 A2D_REG_66 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14:9ESD Event CountR0x0 Field gives the number of ESD events on the copper channel
8RESERVEDR0x0Reserved
7:5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3:0RESERVEDR0x0Reserved

8.48 A2D_REG_68 Register (Offset = 0x444) [Reset = 0x0000]

A2D_REG_68 is shown in Figure 8-48 and described in Table 8-50.

Return to the Summary Table.

Figure 8-48 A2D_REG_68 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDSleep Force ValueSleep Force EnableWAKE pin Force ValueWAKE pin Force Enable
R-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-50 A2D_REG_68 Register Field Descriptions
BitFieldTypeResetDescription
15:4RESERVEDR0x0Reserved
3Sleep Force ValueR/W0x0 1b = Force Sleep when Sleep Force Enable is set to 1
2Sleep Force EnableR/W0x0 1b = Sleep Force Enable (Sleep Force Value has to be set)
1WAKE pin Force ValueR/W0x0 Force value on WAKE pin when WAKE pin Force Enable is set
1b = High
0b = Low
0WAKE pin Force EnableR/W0x0 1b = Enable Force control of WAKE pin

8.49 LEDS_CFG_1 Register (Offset = 0x450) [Reset = 0x2610]

LEDS_CFG_1 is shown in Figure 8-49 and described in Table 8-51.

Return to the Summary Table.

Figure 8-49 LEDS_CFG_1 Register
15141312111098
RESERVEDDisable LED StretchingLED Blink RateRESERVED
R-0x0R/W-0x0R/W-0x2R-0x6
76543210
LED_1 OptionsLED_0 Options
R/W-0x1R/W-0x0
Table 8-51 LEDS_CFG_1 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14Disable LED StretchingR/W0x0 0b = LED pulses are stretched according to the blink rate in 'LED Blink Rate' field
1b = LED pulses are directly connected to RX_DV(for RX activity) and TX_CTRL(for TX Activity)
11:8RESERVEDR0x6Reserved
7:4LED_1 OptionsR/W0x1 0x0 : link OK
0x1 : link OK + blink on TX/RX activity
0x2 : link OK + blink on TX activity
0x3 : link OK + blink on RX activity
0x4 : link OK + 100Base-T1 Leader
0x5 : link OK + 100Base-T1 Follower
0x6 : TX/RX activity with stretch option
0x7 : Reserved
0x8 : Reserved
0x9 : Link lost (remains on until register 0x1 is read)
0xB : xMII TX/RX Error with stretch option
3:0LED_0 OptionsR/W0x0 0x0 : link OK
0x1 : link OK + blink on TX/RX activity
0x2 : link OK + blink on TX activity
0x3 : link OK + blink on RX activity
0x4 : link OK + 100Base-T1 Leader
0x5 : link OK + 100Base-T1 Follower
0x6 : TX/RX activity with stretch option
0x7 : Reserved
0x8 : Reserved
0x9 : Link lost (remains on until register 0x1 is read)
0xB : xMII TX/RX Error with stretch option

8.50 LEDS_CFG_2 Register (Offset = 0x451) [Reset = 0x0009]

LEDS_CFG_2 is shown in Figure 8-50 and described in Table 8-52.

Return to the Summary Table.

Figure 8-50 LEDS_CFG_2 Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDLED_1 Force EnableLED_1 Force ValueLED_1 PolarityLED_0 Force EnableLED_0 Force ValueLED_0 Polarity
R-0x0R-0x0R/W-0x0R/W-0x0R/W-0x1R/W-0x0R/W-0x0R/W-0x1
Table 8-52 LEDS_CFG_2 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12:9RESERVEDR0x0Reserved
8RESERVEDR0x0Reserved
7RESERVEDR0x0Reserved
6RESERVEDR0x0Reserved
5LED_1 Force EnableR/W0x0 1b = Force 'LED_1 Force Value' on LED_1 pin
4LED_1 Force ValueR/W0x0 When LED_1 Force Enable is set, this bit decides the output of LED_1
0b = Low
1b = High
3LED_1 PolarityR/W0x1 Polarity of LED_1:
0b = Active Low polarity
1b = Active High polarity
Default value is decided by the strap on LED_1. If the strap is placed to supply, LED_1 polarity is 0, else LED_1 polarity is 1.
2LED_0 Force EnableR/W0x0 1b = Force 'LED_0 Force Value' on LED_0 pin
1LED_0 Force ValueR/W0x0 When LED_0 Force Enable is set, this bit decides the output of LED_0
0b = Low
1b = High
0LED_0 PolarityR/W0x1 Polarity of LED_0:
0b = Active Low polarity
1b = Active High polarity
Default value is decided by the strap on LED_0. If the strap is placed to supply, LED_0 polarity is 0, else LED_0 polarity is 1

8.51 IO_MUX_CFG_1 Register (Offset = 0x452) [Reset = 0x0000]

IO_MUX_CFG_1 is shown in Figure 8-51 and described in Table 8-53.

Return to the Summary Table.

Figure 8-51 IO_MUX_CFG_1 Register
15141312111098
RESERVEDRESERVEDRESERVEDLED_1 Configuration
R-0x0R-0x0R-0x0R/W-0x0
76543210
RESERVEDRESERVEDRESERVEDLED_0 Configuration
R-0x0R-0x0R-0x0R/W-0x0
Table 8-53 IO_MUX_CFG_1 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14:12RESERVEDR0x0Reserved
11RESERVEDR0x0Reserved
10:8LED_1 ConfigurationR/W0x0 000b = (default: LINK)
010b = WoL
011b = Under-Voltage indication
110b = ESD
111b = interrupt
7RESERVEDR0x0Reserved
6:4RESERVEDR0x0Reserved
3RESERVEDR0x0Reserved
2:0LED_0 ConfigurationR/W0x0 000b = (default: LINK)
010b = WoL
011b = Under-Voltage indication
110b = ESD
111b = interrupt

8.52 IO_MUX_CFG_2 Register (Offset = 0x453) [Reset = 0x0001]

IO_MUX_CFG_2 is shown in Figure 8-52 and described in Table 8-54.

Return to the Summary Table.

Figure 8-52 IO_MUX_CFG_2 Register
15141312111098
Enable TX_ER on LED_1RESERVEDRESERVED
R/W-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x1
Table 8-54 IO_MUX_CFG_2 Register Field Descriptions
BitFieldTypeResetDescription
15Enable TX_ER on LED_1R/W0x0 Configures LED_1 pin to TX_ER
14:9RESERVEDR0x0Reserved
8RESERVEDR0x0Reserved
7:4RESERVEDR0x0Reserved
3RESERVEDR0x0Reserved
2:0RESERVEDR0x1Reserved

8.53 IO_MUX_CFG Register (Offset = 0x456) [Reset = 0x0021]

IO_MUX_CFG is shown in Figure 8-53 and described in Table 8-55.

Return to the Summary Table.

Figure 8-53 IO_MUX_CFG Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDImpedance Control - RX pins
R-0x0R-0x0R-0x0R-0x0R/W-0x1
76543210
Impedance Control - RX pinsImpedance Control - TX_CLK
R/W-0x1R/W-0x1
Table 8-55 IO_MUX_CFG Register Field Descriptions
BitFieldTypeResetDescription
15:14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12:11RESERVEDR0x0Reserved
10RESERVEDR0x0Reserved
9:5Impedance Control - RX pinsR/W0x1 Impedance control for RX_CLK, RX_D[3:0], RX_CTRL, RX_ER
1h = Slew Mode -1
2h = Slew Mode -2
3h = Slew Mode -3
4h = Slew Mode -4
5h = Slew Mode -5
6h = Slew Mode -6
7h = Slew Mode -7
4:0Impedance Control - TX_CLKR/W0x1 1h = Slew Mode -1
2h = Slew Mode -2
3h = Slew Mode -3
4h = Slew Mode -4
5h = Slew Mode -5
6h = Slew Mode -6
7h = Slew Mode -7

8.54 CHIP_SOR_1 Register (Offset = 0x45D) [Reset = 0x0000]

CHIP_SOR_1 is shown in Figure 8-54 and described in Table 8-56.

Return to the Summary Table.

Figure 8-54 CHIP_SOR_1 Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDSTRAP_2 ValueSTRAP_1 ValueRESERVEDSTRAP_0 Value
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
STRAP_5 ValueSTRAP_4 ValueSTRAP_3 ValueRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
Table 8-56 CHIP_SOR_1 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12RESERVEDR0x0Reserved
11STRAP_2 ValueR0x0 strap sampled at power up or reset
10STRAP_1 ValueR0x0 strap sampled at power up or reset
9RESERVEDR0x0Reserved
8STRAP_0 ValueR0x0 strap sampled at power up or reset
7STRAP_5 ValueR0x0 strap sampled at power up or reset
6STRAP_4 ValueR0x0 strap sampled at power up or reset
5STRAP_3 ValueR0x0 strap sampled at power up or reset
4RESERVEDR0x0Reserved
3:2RESERVEDR0x0Reserved
1:0RESERVEDR0x0Reserved

8.55 LED1_ANA_CTRL Register (Offset = 0x45F) [Reset = 0x000C]

LED1_ANA_CTRL is shown in Figure 8-55 and described in Table 8-57.

Return to the Summary Table.

Figure 8-55 LED1_ANA_CTRL Register
15141312111098
RESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVEDLED_1 Clock Mux Control
R-0x0R-0x0R-0x3R/W-0x0
Table 8-57 LED1_ANA_CTRL Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13:5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3:2RESERVEDR0x3Reserved
1:0LED_1 Clock Mux ControlR/W0x0 00b = 25MHz XI Clock for daisy chaining
01b = TX_TCLK for test modes
Register 0x5B7 must be programmed to 0x0443 for clock output on LED_1 pin

8.56 IMPEDANCE_CTRL_1 Register (Offset = 0x461) [Reset = 0x0101]

IMPEDANCE_CTRL_1 is shown in Figure 8-56 and described in Table 8-58.

Return to the Summary Table.

Figure 8-56 IMPEDANCE_CTRL_1 Register
15141312111098
RESERVEDImpedance Control - LED_1
R-0x0R/W-0x1
76543210
RESERVEDImpedance Control - LED_0
R-0x0R/W-0x1
Table 8-58 IMPEDANCE_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:13RESERVEDR0x0Reserved
12:8Impedance Control - LED_1R/W0x1 1h = Slew Mode -1
2h = Slew Mode -2
3h = Slew Mode -3
4h = Slew Mode -4
5h = Slew Mode -5
6h = Slew Mode -6
7h = Slew Mode -7
7:5RESERVEDR0x0Reserved
4:0Impedance Control - LED_0R/W0x1 1h = Slew Mode -1
2h = Slew Mode -2
3h = Slew Mode -3
4h = Slew Mode -4
5h = Slew Mode -5
6h = Slew Mode -6
7h = Slew Mode -7

8.57 LINKUP_TIMER_1 Register (Offset = 0x4EE) [Reset = 0x0000]

LINKUP_TIMER_1 is shown in Figure 8-57 and described in Table 8-59.

Return to the Summary Table.

Figure 8-57 LINKUP_TIMER_1 Register
15141312111098
Link Up Timer [15:0]
R-0x0
76543210
Link Up Timer [15:0]
R-0x0
Table 8-59 LINKUP_TIMER_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0Link Up Timer [15:0]R0x0 Link Up timer calculated from Power-up or Soft Reset or Link Down whichever comes later
Link Up time (in ns) = Link Up Timer [31:0]*40

8.58 LINKUP_TIMER_2 Register (Offset = 0x4EF) [Reset = 0x0000]

LINKUP_TIMER_2 is shown in Figure 8-58 and described in Table 8-60.

Return to the Summary Table.

Figure 8-58 LINKUP_TIMER_2 Register
15141312111098
Link Up Timer [31:16]
R-0x0
76543210
Link Up Timer [31:16]
R-0x0
Table 8-60 LINKUP_TIMER_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0Link Up Timer [31:16]R0x0 Link Up timer calculated from Power-up or Soft Reset or Link Down whichever comes later
Link Up time (in ns) = Link Up Timer [31:0]*40

8.59 TX_PR_FILT_CTRL Register (Offset = 0x523) [Reset = 0x0000]

TX_PR_FILT_CTRL is shown in Figure 8-59 and described in Table 8-61.

Return to the Summary Table.

Figure 8-59 TX_PR_FILT_CTRL Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRESERVEDMDI Polarity InvertMDI Transmit Disable
R-0x0R-0x0R/W-0x0R/W-0x0
Table 8-61 TX_PR_FILT_CTRL Register Field Descriptions
BitFieldTypeResetDescription
15:3RESERVEDR0x0Reserved
2RESERVEDR0x0Reserved
1MDI Polarity InvertR/W0x0 1b = Invert polarity on MDI transmit side
0MDI Transmit DisableR/W0x0 1b = Disable Transmit on MDI
0b = Enable Transmit on MDI

8.60 PG_REG_1 Register (Offset = 0x551) [Reset = 0x0010]

PG_REG_1 is shown in Figure 8-60 and described in Table 8-62.

Return to the Summary Table.

Figure 8-60 PG_REG_1 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRMII CRS_DV ConfigRESERVED
R-0x0R/W-0x1R-0x0
Table 8-62 PG_REG_1 Register Field Descriptions
BitFieldTypeResetDescription
15:5RESERVEDR0x0Reserved
4RMII CRS_DV ConfigR/W0x1 Configure Pin 25 as RX_DV or CRS_DV:
1b = Pin 25 is CRS_DV
0b = Pin 25 is RX_DV
3:0RESERVEDR0x0Reserved

8.61 PG_REG_3 Register (Offset = 0x552) [Reset = 0x0008]

PG_REG_3 is shown in Figure 8-61 and described in Table 8-63.

Return to the Summary Table.

Figure 8-61 PG_REG_3 Register
15141312111098
RESERVED
R-0x8
76543210
RESERVED
R-0x8
Table 8-63 PG_REG_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0RESERVEDR0x8Reserved

8.62 PG_REG_4 Register (Offset = 0x553) [Reset = 0x0000]

PG_REG_4 is shown in Figure 8-62 and described in Table 8-64.

Return to the Summary Table.

Figure 8-62 PG_REG_4 Register
15141312111098
RESERVEDForce Receive Polarity Force EnableReceive polarity Force ValueRESERVED
R-0x0R/W-0x0R/W-0x0R-0x0
76543210
RESERVED
R-0x0
Table 8-64 PG_REG_4 Register Field Descriptions
BitFieldTypeResetDescription
15:14RESERVEDR0x0Reserved
13Force Receive Polarity Force EnableR/W0x0 0x0553[13:12] = 2'b10 : Disable Auto-Polarity Correction and force no polarity inversion
0x0553[13:12] = 2'b11 : Disable Auto-Polarity Correction and force polarity inversion
12Receive polarity Force ValueR/W0x0 0x0553[13:12] = 2'b10 : Disable Auto-Polarity Correction and force no polarity inversion
0x0553[13:12] = 2'b11 : Disable Auto-Polarity Correction and force polarity inversion
11:0RESERVEDR0x0Reserved

8.66 DITH_CTRL_0 Register (Offset = 0x5A0) [Reset = 0x3042]

DITH_CTRL_0 is shown in Figure 8-66 and described in Table 8-68.

Return to the Summary Table.

Figure 8-66 DITH_CTRL_0 Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDDithering Direction
R-0x0R-0x0R-0x1R-0x1R-0x0R-0x0R-0x0R/W-0x0
76543210
RESERVEDRESERVED
R-0x4R-0x2
Table 8-68 DITH_CTRL_0 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14RESERVEDR0x0Reserved
13RESERVEDR0x1Reserved
12RESERVEDR0x1Reserved
11RESERVEDR0x0Reserved
10RESERVEDR0x0Reserved
9RESERVEDR0x0Reserved
8Dithering DirectionR/W0x0 Selects type of Sawtooth profile
  • 0x0 = Reverse Sawtooth profile
  • 0x1 = Increasing Sawtooth profile
7:4RESERVEDR0x4Reserved
3:0RESERVEDR0x2Reserved

8.67 DITH_CTRL_1 Register (Offset = 0x5A1) [Reset = 0x640D]

DITH_CTRL_1 is shown in Figure 8-67 and described in Table 8-69.

Return to the Summary Table.

Figure 8-67 DITH_CTRL_1 Register
15141312111098
Dithering Frequency Step
R/W-0x64
76543210
Dithering Modulation Period
R/W-0xD
Table 8-69 DITH_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:8Dithering Frequency StepR/W0x64 Configure the maximum frequency offset for dithering
0x05A1[15:8] = (Required (delta(f)/f) *217)/(0x5A1[7:0])
Default delta(f)/f = 1%
Keep delta(f)/f limited to ≤ 2%
7:0Dithering Modulation PeriodR/W0xD Configures the modulation period for dithering
0x5A1[7:0] = Dithering Modulation Period / 640 ns)
Default Modulation Period = 13*640ns = 8.34 us

8.68 DITH_RFI_EN_CTRL Register (Offset = 0x5A8) [Reset = 0x0D07]

DITH_RFI_EN_CTRL is shown in Figure 8-68 and described in Table 8-70.

Return to the Summary Table.

Figure 8-68 DITH_RFI_EN_CTRL Register
15141312111098
Dithering ProfileRESERVEDDithering EnableMAC Interface Dithering EnableCore Clocks Dithering EnableRESERVED
R/W-0x0R-0x0R/W-0x0R/W-0x1R/W-0x1R-0x107
76543210
RESERVED
R-0x107
Table 8-70 DITH_RFI_EN_CTRL Register Field Descriptions
BitFieldTypeResetDescription
15:14Dithering ProfileR/W0x0 Select Dithering Frequency Profile
  • 0x0 = Sawtooth
  • 0x1 = Triangular
13RESERVEDR0x0Reserved
12Dithering EnableR/W0x0 1b = Enable Clock Dithering Engine
11MAC Interface Dithering EnableR/W0x1 1b = Enable dithering of RMII, RGMII, MII MAC Interface Outputs
10Core Clocks Dithering EnableR/W0x1 1b = Enable dithering for Internal Digital clocks
9:0RESERVEDR0x107Reserved

8.69 CFG_PCF_DMAC_ADDR Register (Offset = 0x5B2) [Reset = 0x0F6B]

CFG_PCF_DMAC_ADDR is shown in Figure 8-69 and described in Table 8-71.

Return to the Summary Table.

Figure 8-69 CFG_PCF_DMAC_ADDR Register
15141312111098
cfg_pcf_dmac_addr
R/W-0xF6B
76543210
cfg_pcf_dmac_addr
R/W-0xF6B
Table 8-71 CFG_PCF_DMAC_ADDR Register Field Descriptions
BitFieldTypeResetDescription
15:0cfg_pcf_dmac_addrR/W0xF6B Configurable last two bytes of PCF DMAC

8.70 SPARE_IN_FROM_DIG_SL_1 Register (Offset = 0x5B7) [Reset = 0x0043]

SPARE_IN_FROM_DIG_SL_1 is shown in Figure 8-70 and described in Table 8-72.

Return to the Summary Table.

Figure 8-70 SPARE_IN_FROM_DIG_SL_1 Register
15141312111098
RESERVEDRESERVED
R-0x0R-0x43
76543210
RESERVED
R-0x43
Table 8-72 SPARE_IN_FROM_DIG_SL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11:0RESERVEDR0x43Reserved

8.71 CONTROL_REG_1 Register (Offset = 0x5B8) [Reset = 0x0001]

CONTROL_REG_1 is shown in Figure 8-71 and described in Table 8-73.

Return to the Summary Table.

Figure 8-71 CONTROL_REG_1 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDLED GPIO Disable
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R/W-0x1
Table 8-73 CONTROL_REG_1 Register Field Descriptions
BitFieldTypeResetDescription
15:6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3RESERVEDR0x0Reserved
2RESERVEDR0x0Reserved
1RESERVEDR0x0Reserved
0LED GPIO DisableR/W0x1 1b = Disable LED_0/GPIO_0 and LED_1/GPIO_1 pin functions. Pins are in input mode with pull down
0b = Enable LED_0/GPIO_0 and LED_1/GPIO_1 pin functions. Default function enabled is LED ouput

8.72 RGMII_CTRL Register (Offset = 0x600) [Reset = 0x002X]

RGMII_CTRL is shown in Figure 8-72 and described in Table 8-74.

Return to the Summary Table.

Figure 8-72 RGMII_CTRL Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRGMII TX FIFO Half Full ThresholdRGMII EnableInvert RGMII TX Data LinesInvert RGMII RX Data LinesRESERVED
R-0x0R/W-0x2R/W-0xXR/W-0x1R/W-0x0R-0x0
Table 8-74 RGMII_CTRL Register Field Descriptions
BitFieldTypeResetDescription
15:7RESERVEDR0x0Reserved
6:4RGMII TX FIFO Half Full ThresholdR/W0x2 RGMII TX sync FIFO half full threshold
3RGMII EnableR/W0x0 1b = RGMII enable
0b = RGMII Disable
Default value is latched from straps
2Invert RGMII TX Data LinesR/W0x1 0b = Invert RGMII TXD[3:0]
TX_D3 to TX_D0
TX_D2 to TX_D1
TX_D1 to TX_D2
TX_D0 to TX_D3
1Invert RGMII RX Data LinesR/W0x0 1b = Invert RGMII RXD[3:0]
RX_D3 to RX_D0
RX_D2 to RX_D1
RX_D1 to RX_D2
RX_D0 to RX_D3
0RESERVEDR0x0Reserved

8.73 RGMII_FIFO_STATUS Register (Offset = 0x601) [Reset = 0x0000]

RGMII_FIFO_STATUS is shown in Figure 8-73 and described in Table 8-75.

Return to the Summary Table.

Figure 8-73 RGMII_FIFO_STATUS Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRGMII TX FIFO Full ErrorRGMII TX FIFO Empty Error
R-0x0R-0x0R-0x0
Table 8-75 RGMII_FIFO_STATUS Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0x0Reserved
1RGMII TX FIFO Full ErrorR0x0 1b = RGMII TX full error has been indicated
0b = No empty fifo error
This bit is only cleared on device reset
0RGMII TX FIFO Empty ErrorR0x0 1b = RGMII TX empty error has been indicated
0b = No empty fifo error
This bit is only cleared on device reset

8.74 RGMII_CLK_SHIFT_CTRL Register (Offset = 0x602) [Reset = 0x000X]

RGMII_CLK_SHIFT_CTRL is shown in Figure 8-74 and described in Table 8-76.

Return to the Summary Table.

Figure 8-74 RGMII_CLK_SHIFT_CTRL Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRGMII RX ShiftRGMII TX Shift
R-0x0R/W-0xXR/W-0xX
Table 8-76 RGMII_CLK_SHIFT_CTRL Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0x0Reserved
1RGMII RX ShiftR/W0x0 0b = clock and data are aligned
1b = clock is internally delayed by value programmed in DLL RX Shift Delay
0RGMII TX ShiftR/W0x0 0b = clock and data are aligned
1b = clock is internally delayed by value programmed in DLL TX Shift Delay

8.75 SGMII_CTRL_1 Register (Offset = 0x608) [Reset = 0x0X7B]

SGMII_CTRL_1 is shown in Figure 8-75 and described in Table 8-77.

Return to the Summary Table.

Figure 8-75 SGMII_CTRL_1 Register
15141312111098
SGMII TX Error DisableRESERVEDRESERVEDSGMII EnableSGMII TX polarity Invert
R/W-0x0R-0x0R-0x0R/W-0xXR/W-0x0
76543210
SGMII TX polarity InvertRESERVEDRESERVEDRESERVEDRESERVEDSGMII Auto Negotiation Enable
R/W-0x0R-0x3R-0x1R-0x1R-0x1R/W-0x1
Table 8-77 SGMII_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15SGMII TX Error DisableR/W0x0 1b = Disable SGMII TX Error indication
0b = Enable SGMII TX Error indication
14RESERVEDR0x0Reserved
13:10RESERVEDR0x0Reserved
9SGMII EnableR/W0x0 1b = SGMII enable
0b = SGMII Disable
Default value is latched from straps
8SGMII TX polarity InvertR/W0x0 1b = Invert SGMII SOP/N polarity
7SGMII TX polarity InvertR/W0x0 1b = Invert SGMII SIP/N polarity
6:5RESERVEDR0x3Reserved
4RESERVEDR0x1Reserved
3RESERVEDR0x1Reserved
2:1RESERVEDR0x1Reserved
0SGMII Auto Negotiation EnableR/W0x1 1b = Enable SGMII Auto-Negotaition
0b = Disable SGMII Auto-Negotiation

8.76 SGMII_STATUS Register (Offset = 0x60A) [Reset = 0x0000]

SGMII_STATUS is shown in Figure 8-76 and described in Table 8-78.

Return to the Summary Table.

Figure 8-76 SGMII_STATUS Register
15141312111098
RESERVEDSGMII Page ReceivedSGMII Link StatusSGMII Auto Negotiation StatusWord Boundary Align IndicationWord Boundary Sync Status
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVED
R-0x0R-0x0
Table 8-78 SGMII_STATUS Register Field Descriptions
BitFieldTypeResetDescription
15:13RESERVEDR0x0Reserved
12SGMII Page ReceivedR0x0 1b = A new auto neg page received
0b = No new auto neg page received
10SGMII Auto Negotiation StatusR0x0 1b = SGMII autoneg completed
9Word Boundary Align IndicationR0x0 1b = Aligned
8Word Boundary Sync StatusR0x0 1b = sync achieved
0b = sync not achieved
7:4RESERVEDR0x0Reserved
3:0RESERVEDR0x0Reserved

8.77 SGMII_CTRL_2 Register (Offset = 0x60C) [Reset = 0x0044]

SGMII_CTRL_2 is shown in Figure 8-77 and described in Table 8-79.

Return to the Summary Table.

Figure 8-77 SGMII_CTRL_2 Register
15141312111098
RESERVEDRESERVEDRESERVEDRESERVED
R-0x0R-0x0R-0x0R-0x0
76543210
SGMII TX FIFO Half Full ThresholdSGMII RX FIFO Half Full Threshold
R/W-0x4R/W-0x4
Table 8-79 SGMII_CTRL_2 Register Field Descriptions
BitFieldTypeResetDescription
15:11RESERVEDR0x0Reserved
10RESERVEDR0x0Reserved
9RESERVEDR0x0Reserved
8RESERVEDR0x0Reserved
7:4SGMII TX FIFO Half Full ThresholdR/W0x4 SGMII TX sync FIFO half full threshold
3:0SGMII RX FIFO Half Full ThresholdR/W0x4 SGMII RX sync FIFO half full threshold

8.78 SGMII_FIFO_STATUS Register (Offset = 0x60D) [Reset = 0x0000]

SGMII_FIFO_STATUS is shown in Figure 8-78 and described in Table 8-80.

Return to the Summary Table.

Figure 8-78 SGMII_FIFO_STATUS Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDSGMII RX FIFO Full ErrorSGMII RX FIFO Empty ErrorSGMII TX FIFO Full ErrorSGMII TX FIFO Empty Error
R-0x0RC-0x0RC-0x0RC-0x0RC-0x0
Table 8-80 SGMII_FIFO_STATUS Register Field Descriptions
BitFieldTypeResetDescription
15:4RESERVEDR0x0Reserved
3SGMII RX FIFO Full ErrorRC0x0 1b = SGMII RX fifo full error has been indicated
0b = No error indication
2SGMII RX FIFO Empty ErrorRC0x0 1b = SGMII RX fifo empty error has been indicated
0b = No error indication
1SGMII TX FIFO Full ErrorRC0x0 1b = SGMII TX fifo full error has been indicated
0b = No error indication
0SGMII TX FIFO Empty ErrorRC0x0 1b = SGMII TX fifo empty error has been indicated
0b = No error indication

8.79 PRBS_STATUS_1 Register (Offset = 0x618) [Reset = 0x0000]

PRBS_STATUS_1 is shown in Figure 8-79 and described in Table 8-81.

Return to the Summary Table.

Figure 8-79 PRBS_STATUS_1 Register
15141312111098
RESERVED
R-0x0
76543210
PRBS Error Overflow Counter
R-0x0
Table 8-81 PRBS_STATUS_1 Register Field Descriptions
BitFieldTypeResetDescription
15:8RESERVEDR0x0Reserved
7:0PRBS Error Overflow CounterR0x0 Holds number of error counter overflow that received by the PRBS checker.
Value in this register is locked when write is done to register prbs_status_6 bit[0] or bit[1]. Counter stops on 0xFF.
Note: when PRBS counters work in single mode, overflow counter is not active

8.80 PRBS_CTRL_1 Register (Offset = 0x619) [Reset = 0x0574]

PRBS_CTRL_1 is shown in Figure 8-80 and described in Table 8-82.

Return to the Summary Table.

Figure 8-80 PRBS_CTRL_1 Register
15141312111098
RESERVEDRESERVEDSend PacketRESERVEDPRBS Check Select
R-0x0R-0x0R-0/W1S-0x0R-0x0R/W-0x5
76543210
RESERVEDPRBS Transmit SelectPRBS Count ModePRBS Checker EnablePRBS Generation EnablePRBS or Packet Generation Enable
R-0x0R/W-0x7R/W-0x0R/W-0x1R/W-0x0R/W-0x0
Table 8-82 PRBS_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:14RESERVEDR0x0Reserved
13RESERVEDR0x0Reserved
12Send PacketR-0/W1S0x0 Enables generating MAC packet with fix/incremental data with CRC
(0x619[0] has to be set and 0x619[1] has to be clear)
Cleared automatically when pkt_done is set
1b = Transmit MAC packet with CRC
0b = Stop MAC packet
11RESERVEDR0x0Reserved
10:8PRBS Check SelectR/W0x5 Selects the direction of PRBS checker reception
000b = Checker receives from RGMII TX
001b = Checker receives SGMII TX
101b = Checker receives from MDI RX
7RESERVEDR0x0Reserved
6:4PRBS Transmit SelectR/W0x7 Selects the direction of PRBS transmission
000b = PRBS transmits to RGMII RX
001b = PRBS transmits to SGMII RX
101b = PRBS transmits to MDI TX
3PRBS Count ModeR/W0x0 1b = Continuous mode, when one of the PRBS counters reaches max value, pulse is generated and counter starts counting from zero again
0b = Single mode, When one of the PRBS counters reaches max value, PRBS checker stops counting.
2PRBS Checker EnableR/W0x1 Enable PRBS checker (to receive data)
To be enabled for counters in 0x63C, 0x63D, 0x63E to work
1b = Enable PRBS checker
1PRBS Generation EnableR/W0x0 If 0x619[0] is set,
1b = Transmits PRBS packet
0b = Transmits non-PRBS packet (PRBS checker is also Disabled in this case)
0PRBS or Packet Generation EnableR/W0x0 1b = Enable packet/PRBS generator
0b = Disable packet/PRBS generator

8.81 PRBS_CTRL_2 Register (Offset = 0x61A) [Reset = 0x05DC]

PRBS_CTRL_2 is shown in Figure 8-81 and described in Table 8-83.

Return to the Summary Table.

Figure 8-81 PRBS_CTRL_2 Register
15141312111098
Packet Length
R/W-0x5DC
76543210
Packet Length
R/W-0x5DC
Table 8-83 PRBS_CTRL_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0Packet LengthR/W0x5DC Sets packet length (in bytes) between the PRBS packets or non-PRBS packets generated

8.82 PRBS_CTRL_3 Register (Offset = 0x61B) [Reset = 0x007D]

PRBS_CTRL_3 is shown in Figure 8-82 and described in Table 8-84.

Return to the Summary Table.

Figure 8-82 PRBS_CTRL_3 Register
15141312111098
RESERVED
R-0x0
76543210
PRBS IPG
R/W-0x7D
Table 8-84 PRBS_CTRL_3 Register Field Descriptions
BitFieldTypeResetDescription
15:8RESERVEDR0x0Reserved
7:0PRBS IPGR/W0x7D Sets IPG (in bytes) between the PRBS packets or non-PRBS packets generated

8.83 PRBS_STATUS_2 Register (Offset = 0x61C) [Reset = 0x0000]

PRBS_STATUS_2 is shown in Figure 8-83 and described in Table 8-85.

Return to the Summary Table.

Figure 8-83 PRBS_STATUS_2 Register
15141312111098
PRBS Checker Byte Count
R-0x0
76543210
PRBS Checker Byte Count
R-0x0
Table 8-85 PRBS_STATUS_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0PRBS Checker Byte CountR0x0 Holds number of total bytes that received by the PRBS checker
Value in register is locked when 0x620[0] or 0x620[1] are written
When PRBS Count Mode set to zero, count stops on 0xFFFF
This counter is cleared if this counter is read after programming 0x620[1]=1

8.84 PRBS_STATUS_3 Register (Offset = 0x61D) [Reset = 0x0000]

PRBS_STATUS_3 is shown in Figure 8-84 and described in Table 8-86.

Return to the Summary Table.

Figure 8-84 PRBS_STATUS_3 Register
15141312111098
PRBS Checker Packet Count-1
R-0x0
76543210
PRBS Checker Packet Count-1
R-0x0
Table 8-86 PRBS_STATUS_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0PRBS Checker Packet Count-1R0x0 Holds Bits [15:0] of number of total packets received by the PRBS checker
Value in register is locked when 0x620[0] or 0x620[1] are written
When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF
This counter is cleared if 0x61D,0x61E are read in the same order, after programming 0x620[1]=1

8.85 PRBS_STATUS_4 Register (Offset = 0x61E) [Reset = 0x0000]

PRBS_STATUS_4 is shown in Figure 8-85 and described in Table 8-87.

Return to the Summary Table.

Figure 8-85 PRBS_STATUS_4 Register
15141312111098
PRBS Checker Packet Count-2
R-0x0
76543210
PRBS Checker Packet Count-2
R-0x0
Table 8-87 PRBS_STATUS_4 Register Field Descriptions
BitFieldTypeResetDescription
15:0PRBS Checker Packet Count-2R0x0 Holds Bits [31:16] of number of total packets received by the PRBS checker
Value in register is locked when 0x620[0] or 0x620[1] are written
When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF
This counter is cleared if 0x61D,0x61E are read in the same order, after programming 0x620[1]=1

8.86 PRBS_STATUS_5 Register (Offset = 0x620) [Reset = 0x0000]

PRBS_STATUS_5 is shown in Figure 8-86 and described in Table 8-88.

Return to the Summary Table.

Figure 8-86 PRBS_STATUS_5 Register
15141312111098
RESERVEDMAC Packet Gen DoneMAC Packet Gen BusyPRBS Checker Packet Count Overflow StatusPRBS Checker Byte Count Overflow StatusPRBS Lock
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
PRBS Error Count
R-0x0
Table 8-88 PRBS_STATUS_5 Register Field Descriptions
BitFieldTypeResetDescription
15:13RESERVEDR0x0Reserved
12MAC Packet Gen DoneR0x0 Set when all MAC packets with CRC are transmitted
1b = MAC packets transmission completed
0b = MAC packet transmission in progress
11MAC Packet Gen BusyR0x0 1b = Packet generator is in process
0b = Packet generator is not in process
10PRBS Checker Packet Count Overflow StatusR0x0 If PRBS Checker Packet Count overflows, this status bit is set to 1
This overflow status is cleared after clearing PRBS byte counter using 0x620[1]
9PRBS Checker Byte Count Overflow StatusR0x0 If PRBS Checker Byte Count overflows, this status bit is set to 1
This overflow status is cleared after clearing PRBS byte counter using 0x620[1]
8PRBS LockR0x0 1b = PRBS checker is locked and synced with the received stream
7:0PRBS Error CountR0x0 Writing 1 to bit0 locks all PRBS counters
Writing 1 to bit1 locks all PRBS counters and clears the counters on read of those specific registers
Bits [1:0] are self-cleared after write
Reading Bits[7:0] after writing bit0/bit1, gives the number of error bits received by PRBS checker
When PRBS Count Mode set to zero, count stops on 0xFF

8.87 PRBS_STATUS_6 Register (Offset = 0x622) [Reset = 0x0000]

PRBS_STATUS_6 is shown in Figure 8-87 and described in Table 8-89.

Return to the Summary Table.

Figure 8-87 PRBS_STATUS_6 Register
15141312111098
PRBS Packer Error Count-1
R-0x0
76543210
PRBS Packer Error Count-1
R-0x0
Table 8-89 PRBS_STATUS_6 Register Field Descriptions
BitFieldTypeResetDescription
15:0PRBS Packer Error Count-1R0x0 Holds Bits [15:0] of number of total packets received with error by the PRBS checker
Value in register is locked when 0x620[0] or 0x620[1] are written
When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF
This counter is cleared if 0x622,0x623 are read in the same order, after programming 0x620[1]=1

8.88 PRBS_STATUS_7 Register (Offset = 0x623) [Reset = 0x0000]

PRBS_STATUS_7 is shown in Figure 8-88 and described in Table 8-90.

Return to the Summary Table.

Figure 8-88 PRBS_STATUS_7 Register
15141312111098
PRBS Packer Error Count-2
R-0x0
76543210
PRBS Packer Error Count-2
R-0x0
Table 8-90 PRBS_STATUS_7 Register Field Descriptions
BitFieldTypeResetDescription
15:0PRBS Packer Error Count-2R0x0 Holds Bits [31:16] of number of total packets received with error by the PRBS checker
Value in register is locked when 0x620[0] or 0x620[1] are written
When PRBS Count Mode set to zero, count stops on 0xFFFFFFFF
This counter is cleared if 0x622,0x623 are read in the same order, after programming 0x620[1]=1

8.89 PRBS_CTRL_4 Register (Offset = 0x624) [Reset = 0x5511]

PRBS_CTRL_4 is shown in Figure 8-89 and described in Table 8-91.

Return to the Summary Table.

Figure 8-89 PRBS_CTRL_4 Register
15141312111098
MAC Packet Data
R/W-0x55
76543210
MAC Packet ModePattern Length in MAC PacketsPacket Count for MAC packets Mode
R/W-0x0R/W-0x2R/W-0x1
Table 8-91 PRBS_CTRL_4 Register Field Descriptions
BitFieldTypeResetDescription
15:8MAC Packet DataR/W0x55 Fixed data to be sent when MAC Packet Mode is set to Fixed mode
7:6MAC Packet ModeR/W0x0 00b = Incremental
01b = Fixed
10b = PRBS
11b = PRBS
5:3Pattern Length in MAC PacketsR/W0x2 MAC Packets have Destination Address, Source Address, Programmed Pattern, PRBS/Fixed/Incremental Data
The length of Programmed Pattern can be confgured through this register. Pattern can be programmed through 0x625,0x626,0x627
000b = 6 bytes
001b = 1 bytes
010b = 2 bytes
011b = 3 bytes
100b = 4 bytes
101b = 5 bytes
110b = 6 bytes
111b = 6 bytes
2:0Packet Count for MAC packets ModeR/W0x1 000b = 1 packet
001b = 10 packets
010b = 100 packets
011b = 1000 packets
100b = 10000 packets
101b = 100000 packets
110b = 1000000 packets
111b = Continuous packets

8.90 PATTERN_CTRL_1 Register (Offset = 0x625) [Reset = 0x0000]

PATTERN_CTRL_1 is shown in Figure 8-90 and described in Table 8-92.

Return to the Summary Table.

Figure 8-90 PATTERN_CTRL_1 Register
15141312111098
Pattern in MAC Packets [15:0]
R/W-0x0
76543210
Pattern in MAC Packets [15:0]
R/W-0x0
Table 8-92 PATTERN_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0Pattern in MAC Packets [15:0]R/W0x0 Bytes 0,1 of programmable pattern in MAC packets

8.91 PATTERN_CTRL_2 Register (Offset = 0x626) [Reset = 0x0000]

PATTERN_CTRL_2 is shown in Figure 8-91 and described in Table 8-93.

Return to the Summary Table.

Figure 8-91 PATTERN_CTRL_2 Register
15141312111098
Pattern in MAC Packets [31:16]
R/W-0x0
76543210
Pattern in MAC Packets [31:16]
R/W-0x0
Table 8-93 PATTERN_CTRL_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0Pattern in MAC Packets [31:16]R/W0x0 Bytes 2,3 of programmable pattern in MAC packets

8.92 PATTERN_CTRL_3 Register (Offset = 0x627) [Reset = 0x0000]

PATTERN_CTRL_3 is shown in Figure 8-92 and described in Table 8-94.

Return to the Summary Table.

Figure 8-92 PATTERN_CTRL_3 Register
15141312111098
Pattern in MAC Packets [47:32]
R/W-0x0
76543210
Pattern in MAC Packets [47:32]
R/W-0x0
Table 8-94 PATTERN_CTRL_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0Pattern in MAC Packets [47:32]R/W0x0 Bytes 4,5 of programmable pattern in MAC packets

8.93 PMATCH_CTRL_1 Register (Offset = 0x628) [Reset = 0x0000]

PMATCH_CTRL_1 is shown in Figure 8-93 and described in Table 8-95.

Return to the Summary Table.

Figure 8-93 PMATCH_CTRL_1 Register
15141312111098
Destination Address in MAC Packets [15:0]
R/W-0x0
76543210
Destination Address in MAC Packets [15:0]
R/W-0x0
Table 8-95 PMATCH_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0Destination Address in MAC Packets [15:0]R/W0x0 Destination Address field in the generated MAC packets

8.94 PMATCH_CTRL_2 Register (Offset = 0x629) [Reset = 0x0000]

PMATCH_CTRL_2 is shown in Figure 8-94 and described in Table 8-96.

Return to the Summary Table.

Figure 8-94 PMATCH_CTRL_2 Register
15141312111098
Destination Address in MAC Packets [31:16]
R/W-0x0
76543210
Destination Address in MAC Packets [31:16]
R/W-0x0
Table 8-96 PMATCH_CTRL_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0Destination Address in MAC Packets [31:16]R/W0x0 Destination Address field in the generated MAC packets

8.95 PMATCH_CTRL_3 Register (Offset = 0x62A) [Reset = 0x0000]

PMATCH_CTRL_3 is shown in Figure 8-95 and described in Table 8-97.

Return to the Summary Table.

Figure 8-95 PMATCH_CTRL_3 Register
15141312111098
Destination Address in MAC Packets [47:32]
R/W-0x0
76543210
Destination Address in MAC Packets [47:32]
R/W-0x0
Table 8-97 PMATCH_CTRL_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0Destination Address in MAC Packets [47:32]R/W0x0 Destination Address field in the generated MAC packets

8.96 PKT_CRC_STAT Register (Offset = 0x638) [Reset = 0x0000]

PKT_CRC_STAT is shown in Figure 8-96 and described in Table 8-98.

Return to the Summary Table.

Figure 8-96 PKT_CRC_STAT Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRX Bad CRCTX Bad CRC
R-0x0R-0x0R-0x0
Table 8-98 PKT_CRC_STAT Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0x0Reserved
1RX Bad CRCR0x0 1b = CRC error detected in the packet received from the MDI receiver
0TX Bad CRCR0x0 1b = CRC error detected in the packet transmitted on MDI transmitter

8.97 TX_PKT_CNT_1 Register (Offset = 0x639) [Reset = 0x0000]

TX_PKT_CNT_1 is shown in Figure 8-97 and described in Table 8-99.

Return to the Summary Table.

Figure 8-97 TX_PKT_CNT_1 Register
15141312111098
TX Packet Count [15:0]
R-0x0
76543210
TX Packet Count [15:0]
R-0x0
Table 8-99 TX_PKT_CNT_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0TX Packet Count [15:0]R0x0 Lower 16 bits of TX packets from MAC counter
Note : register is cleared when 0x639, 0x63A, 0x63B are read in sequence

8.98 TX_PKT_CNT_2 Register (Offset = 0x63A) [Reset = 0x0000]

TX_PKT_CNT_2 is shown in Figure 8-98 and described in Table 8-100.

Return to the Summary Table.

Figure 8-98 TX_PKT_CNT_2 Register
15141312111098
TX Packet Count [31:16]
R-0x0
76543210
TX Packet Count [31:16]
R-0x0
Table 8-100 TX_PKT_CNT_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0TX Packet Count [31:16]R0x0 Upper 16 bits of TX packets from MAC counter
Note : register is cleared when 0x639, 0x63A, 0x63B are read in sequence

8.99 TX_PKT_CNT_3 Register (Offset = 0x63B) [Reset = 0x0000]

TX_PKT_CNT_3 is shown in Figure 8-99 and described in Table 8-101.

Return to the Summary Table.

Figure 8-99 TX_PKT_CNT_3 Register
15141312111098
TX Error Packet Count
R-0x0
76543210
TX Error Packet Count
R-0x0
Table 8-101 TX_PKT_CNT_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0TX Error Packet CountR0x0 TX packets from MAC with CRC error counter
Note : register is cleared when 0x639, 0x63A, 0x63B are read in sequence

8.100 RX_PKT_CNT_1 Register (Offset = 0x63C) [Reset = 0x0000]

RX_PKT_CNT_1 is shown in Figure 8-100 and described in Table 8-102.

Return to the Summary Table.

Figure 8-100 RX_PKT_CNT_1 Register
15141312111098
RX Packet Count [15:0]
R-0x0
76543210
RX Packet Count [15:0]
R-0x0
Table 8-102 RX_PKT_CNT_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0RX Packet Count [15:0]R0x0 Lower 16 bits of RX packets received from MDI
Note : register is cleared when 0x63C, 0x63D, 0x63E are read in sequence

8.101 RX_PKT_CNT_2 Register (Offset = 0x63D) [Reset = 0x0000]

RX_PKT_CNT_2 is shown in Figure 8-101 and described in Table 8-103.

Return to the Summary Table.

Figure 8-101 RX_PKT_CNT_2 Register
15141312111098
RX Packet Count [31:16]
R-0x0
76543210
RX Packet Count [31:16]
R-0x0
Table 8-103 RX_PKT_CNT_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0RX Packet Count [31:16]R0x0 Upper 16 bits of RX packets received from MDI
Note : register is cleared when 0x63C, 0x63D, 0x63E are read in sequence

8.102 RX_PKT_CNT_3 Register (Offset = 0x63E) [Reset = 0x0000]

RX_PKT_CNT_3 is shown in Figure 8-102 and described in Table 8-104.

Return to the Summary Table.

Figure 8-102 RX_PKT_CNT_3 Register
15141312111098
RX Error Packet Count
R-0x0
76543210
RX Error Packet Count
R-0x0
Table 8-104 RX_PKT_CNT_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0RX Error Packet CountR0x0 Rx packet w error (CRC error) counter
Note : register is cleared when 0x63C, 0x63D, 0x63E are read in sequence

8.103 RMII_CTRL_1 Register (Offset = 0x648) [Reset = 0x01X0]

RMII_CTRL_1 is shown in Figure 8-103 and described in Table 8-105.

Return to the Summary Table.

Figure 8-103 RMII_CTRL_1 Register
15141312111098
RESERVEDRESERVEDRESERVEDRMII Half Full Threshold
R-0x0R-0x0R-0x0R/W-0x2
76543210
RMII Half Full ThresholdRMII EnableRESERVEDRMII Follower EnableRESERVEDRESERVEDRMII Rev1.0 EnableRMII Enhanced Mode Enable
R/W-0x2R/W-0xXR-0x1R/W-0xXR-0x0R-0x0R/W-0x0R/W-0x0
Table 8-105 RMII_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11RESERVEDR0x0Reserved
10RESERVEDR0x0Reserved
9:7RMII Half Full ThresholdR/W0x2 FIFO Half Full Threshold in nibbles for the RMII Rx FIFO
6RMII EnableR/W0x0 1b = RMII Enable
5RESERVEDR0x1Reserved
4RMII Follower EnableR/W0x0 1b = RMII Follower mode is enabled
Not recommended to configure this bit. Can be used as a status bit
3RESERVEDR0x0Reserved
2RESERVEDR0x0Reserved
1RMII Rev1.0 EnableR/W0x0 1b = Enable RMII rev1.0
0RMII Enhanced Mode EnableR/W0x0 1b = Enable RMII Enhanced mode

8.104 RMII_STATUS_1 Register (Offset = 0x649) [Reset = 0x0000]

RMII_STATUS_1 is shown in Figure 8-104 and described in Table 8-106.

Return to the Summary Table.

Figure 8-104 RMII_STATUS_1 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRMII FIFO Empty ErrorRMII FIFO Full Error
R-0x0R-0x0R-0x0
Table 8-106 RMII_STATUS_1 Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0x0Reserved
1RMII FIFO Empty ErrorR0x0 Clear on read bit
RMII fifo underflow error status
0RMII FIFO Full ErrorR0x0 Clear on Read bit
RMII fifo overflow status

8.105 PTP_CTL Register (Offset = 0xD00) [Reset = 0x0000]

PTP_CTL is shown in Figure 8-105 and described in Table 8-107.

Return to the Summary Table.

This register provides basic controls for the PTP 802.1AS operation

Figure 8-105 PTP_CTL Register
15141312111098
RESERVEDTrigger SelectTrigger DisableTrigger Enable
R-0x0R/W-0x0R/W-0x0R/W-0x0
76543210
Trigger ReadTrigger LoadRead PTP ClockLoad PTP ClockStep PTP ClockPTP EnablePTP DisablePTP Reset
R/W-0x0R/W-0x0WSC-0x0WSC-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-107 PTP_CTL Register Field Descriptions
BitFieldTypeResetDescription
15:13RESERVEDR0x0Reserved
12:10Trigger SelectR/W0x0 PTP Trigger Select:
This field selects the Trigger for loading control information or for enabling the Trigger.
000b = Trigger-0
001b = Trigger-1
010b = Trigger-2
011b = Trigger-3
100b = Trigger-4
101b = Trigger-5
110b = Trigger-6
111b = Trigger-7
9Trigger DisableR/W0x0 Disable PTP Trigger:
Setting this bit disables the selected Trigger. This bit does not indicate Disable status for Triggers. Use the PTP Trigger Status register to determine Trigger Status. This bit is self-clearing and always reads back as 0.
Disabling a Trigger does not disconnect it from a GPIO pin. The Trigger value is still driven to the GPIO if the Trigger is assigned to a GPIO.
8Trigger EnableR/W0x0 Enable PTP Trigger:
Setting this bit enables the selected Trigger. This bit does not indicate Enable status for Triggers. Use the PTP Trigger Status register to determine Trigger Status. This bit is self-clearing and always reads back as 0.

7Trigger ReadR/W0x0 Read PTP Trigger:
Setting this bit begins the Trigger Read process. The Trigger is selected based on the setting of the 'Trigger Select' bits in this register. Upon setting this bit, subsequent reads of the PTP_TDR register returns the Trigger Control values.
This bit is self-clearing and always reads back as 0.
6Trigger LoadR/W0x0 Load PTP Trigger:
Setting this bit disables the selected Trigger and begin the Trigger load process. The Trigger is selected based on the setting of the 'Trigger Select' bits in this register. Upon setting this bit, subsequent writes to the PTP_TDR sets the Trigger Control fields for the selected Trigger.
The Trigger Load is completed after all fields have been written, or the 'Trigger Enable' bit has been set in this register. This bit is self-clearing and reads back as 0 when the Trigger Load is completed either by writing all Trigger Control fields, or by setting the Trigger Enable.
5Read PTP ClockWSC0x0 Read PTP Clock:
Setting this bit causes the device to sample the PTP Clock time value. The time value is made available for reading through the PTP_TDR register.
This bit is self-clearing and always reads back as 0.
4Load PTP ClockWSC0x0 Load PTP Clock:
Setting this bit causes the device to load the PTP Clock time value from data previously written to the PTP_TDR register.
This bit is self-clearing and always reads back as 0.
3Step PTP ClockR/W0x0 Step PTP Clock:
Setting this bit causes the device to add a value to the PTP Clock. The value to be added is the value previously written to the PTP_TDR register.
This bit is self-clearing and always reads back as 0.
2PTP EnableR/W0x0 Enable PTP Clock:
Setting this bit enables the PTP Clock. Reading this bit returns the current enabled value.
Writing a 0 to this bit has no effect.
1PTP DisableR/W0x0 Disable PTP Clock:
Setting this bit disables the PTP Clock. Writing a 0 to this bit has no effect. This bit is self-clearing and always reads back as 0.
0PTP ResetR/W0x0 Reset PTP Clock:
Setting this bit resets the PTP Clock and associated logic. In addition, the 802.1AS registers are reset, with the exception of the PTP_COC and PTP_CLKSRC registers.
Unlike other bits in this register, this bit is not self-clearing and must be written to 0 to release the clock and logic from reset.

8.106 PTP_TDR Register (Offset = 0xD01) [Reset = 0x0000]

PTP_TDR is shown in Figure 8-106 and described in Table 8-108.

Return to the Summary Table.

This register provides a mechanism for reading and writing the 802.1AS Time and Trigger Control values. The function of this register is determined by controls in the PTP control register

Figure 8-106 PTP_TDR Register
15141312111098
Time Data
R/W-0x0
76543210
Time Data
R/W-0x0
Table 8-108 PTP_TDR Register Field Descriptions
BitFieldTypeResetDescription
15:0Time DataR/W0x0 Time Data:
On Reads, successively returns 16-bit values of the Clock time or Trigger Control information as selected by controls in the PTP Control register. Additional reads beyond the available fields always returns 0.
On Writes, successively stores the 16-bit values of Clock time or Trigger Control Information as selected by controls in the PTP Control register.

8.107 PTP_STS Register (Offset = 0xD02) [Reset = 0x0000]

PTP_STS is shown in Figure 8-107 and described in Table 8-109.

Return to the Summary Table.

This register provides basic status and interrupt control for the 802.1AS PTP operation.

Figure 8-107 PTP_STS Register
15141312111098
RESERVEDTX Timestamp ReadyRX Timestamp ReadyTrigger DoneEvent Ready
R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDTX Timestamp Ready Interrupt EnableRX Timestamp Ready Interrupt EnableTrigger Done Interrupt EnableEvent Ready Enable
R-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-109 PTP_STS Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11TX Timestamp ReadyR0x0 Transmit Timestamp Ready:
A Transmit Timestamp is available for an outbound PTP Message.
This bit is cleared upon read of the Transmit Timestamp if no other timestamps are ready.
10RX Timestamp ReadyR0x0 Receive Timestamp Ready:
A Receive Timestamp is available for an inbound PTP Message.
This bit is cleared upon read of the Receive Timestamp if no other timestamps are ready.
9Trigger DoneR0x0 PTP Trigger Done:
A PTP Trigger has occurred. This bit is cleared upon read. This bit is only set if Trigger Notification is turned on for the Trigger through the Trigger Configuration registers.
Note that if periodic trigger is set, this interrupt does not get asserted unless the programmed trigger has resulted in a erroneous condition. If TRIG_IF_LATE bit is set, even an erroneous condition does not give out an interrupt
8Event ReadyR0x0 PTP Event Timestamp Ready:
A PTP Event Timestamp is available.
This bit is cleared upon read of the PTP Event Status register if no other event timestamps are ready.
7:5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3TX Timestamp Ready Interrupt EnableR/W0x0 Enable Transmit Timestamp Interrupt:
Enable Interrupt on Transmit Timestamp Ready.
2RX Timestamp Ready Interrupt EnableR/W0x0 Enable Receive Timestamp Interrupt:
Enable Interrupt on Receive Timestamp Ready.
1Trigger Done Interrupt EnableR/W0x0 Enable Trigger Interrupt:
Enable Interrupt on Trigger Completion.
0Event Ready EnableR/W0x0 Enable Event Interrupt:
Enable Interrupt on Event Timestamp Ready.

8.108 PTP_TSTS Register (Offset = 0xD03) [Reset = 0x0000]

PTP_TSTS is shown in Figure 8-108 and described in Table 8-110.

Return to the Summary Table.

This register provides status of the 802.1AS PTP Triggers. The bits in this register indicate the current status for each of the Trigger modules. The error bits are set if the associated notification enable (TRIG_NOTIFY) is set in the PTP Trigger Configuration Registers

Figure 8-108 PTP_TSTS Register
15141312111098
Trigger-7 Error IndicationTrigger-7 Active StatusTrigger-6 Error IndicationTrigger-6 Active StatusTrigger-5 Error IndicationTrigger-5 Active StatusTrigger-4 Error IndicationTrigger-4 Active Status
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
76543210
Trigger-3 Error IndicationTrigger-3 Active StatusTrigger-2 Error IndicationTrigger-2 Active StatusTrigger-1 Error IndicationTrigger-1 Active StatusTrigger-0 Error IndicationTrigger-0 Active Status
R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0R-0x0
Table 8-110 PTP_TSTS Register Field Descriptions
BitFieldTypeResetDescription
15Trigger-7 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
14Trigger-7 Active StatusR0x0 This bit indicates that the Trigger is enabled and has not completed.
13Trigger-6 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
12Trigger-6 Active StatusR0x0 This bit indicates that the Trigger is enabled and has not completed.
11Trigger-5 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
10Trigger-5 Active StatusR0x0 This bit indicates that the Trigger is enabled and has not completed.
9Trigger-4 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
8Trigger-4 Active StatusR0x0 This bit indicates that the Trigger is enabled and has not completed.
7Trigger-3 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
6Trigger-3 Active StatusR0x0 This bit indicates that the Trigger is enabled and has not completed.
5Trigger-2 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
4Trigger-2 Active StatusR0x0 This bit indicates that the Trigger is enabled and has not completed.
3Trigger-1 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
2Trigger-1 Active StatusR0x0 This bit indicates the Trigger is enabled and has not completed.
1Trigger-0 Error IndicationR0x0 This bit indicates that the Trigger was improperly programmed to trigger at a time prior to the current time. This bit is cleared when the Trigger is Disabled and/ or rearmed.
0Trigger-0 Active StatusR0x0 This bit indicates that the Trigger is enabled and has not completed.

8.109 PTP_RATEL Register (Offset = 0xD04) [Reset = 0x0000]

PTP_RATEL is shown in Figure 8-109 and described in Table 8-111.

Return to the Summary Table.

This register contains the low 16-bits of the PTP Rate control. The PTP Rate Control indicates a positive or negative adjustment to the reference clock period in units of 2-32 ns. On each reference clock cycle, the PTP Clock is adjusted by adding ref_clk_period +/- PTP_Rate. Write the PTP Rate as PTP_RATEH, followed by PTP_RATEL. The rate takes effect on the write to the PTP_RATEL register

Figure 8-109 PTP_RATEL Register
15141312111098
PTP Rate Control Low
R/W-0x0
76543210
PTP Rate Control Low
R/W-0x0
Table 8-111 PTP_RATEL Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Rate Control LowR/W0x0 PTP Rate Control Low 16-bits:
Writing to this register sets the low 16-bits of the Rate Control value. The Rate Control value is in units of 2-32 ns. Upon writing to this register, the full Rate Control value is loaded to the device.

8.110 PTP_RATEH Register (Offset = 0xD05) [Reset = 0x0000]

PTP_RATEH is shown in Figure 8-110 and described in Table 8-112.

Return to the Summary Table.

This register contains the upper 10-bits of the 26-bit PTP Rate control. In addition, it contains a direction control to indicate whether the device is operating faster or slower than the reference clock frequency. When setting the PTP Rate, write this register first, followed by a write to the PTP_RATEL register. The rate takes effect on the write to the PTP_RATEL register.

Figure 8-110 PTP_RATEH Register
15141312111098
PTP Rate DirectionTemporary Rate EnableRESERVEDPTP Rate Control High
R/W-0x0R/W-0x0R-0x0R/W-0x0
76543210
PTP Rate Control High
R/W-0x0
Table 8-112 PTP_RATEH Register Field Descriptions
BitFieldTypeResetDescription
15PTP Rate DirectionR/W0x0 The setting of this bit controls whether the device operates at a higher or lower frequency than the reference clock.
  • 0x0 = The PTP RATE value is added to the clock on every cycle indicating Lower Frequency
  • 0x1 = The PTP RATE value is subtracted from the clock on every cycle indicating Higher Frequency
14Temporary Rate EnableR/W0x0 PTP Temporary Rate:
Setting this bit causes the rate to be applied to the clock for the duration set in the PTP Temporary Rate Duration register (PTP_TRD).
  • 0x0 = Normal Rate
  • 0x1 = Temporary Rate
13:10RESERVEDR0x0Reserved
9:0PTP Rate Control HighR/W0x0 PTP Rate Control High 10-bits:
Writing to this register sets the high 10-bits of the Rate Control value. The Rate Control value is in units of 2-32 ns.

8.111 PTP_TXTS Register (Offset = 0xD08) [Reset = 0x0000]

PTP_TXTS is shown in Figure 8-111 and described in Table 8-113.

Return to the Summary Table.

This register provides a mechanism for reading the Transmit Timestamp. The fields are read in the following order:
Timestamp_ns [15:0];

Overflow_cnt[1:0], Timestamp_ns[29:16];

Timestamp_sec[15:0],

Timestamp_sec[31:16]

The Overflow_cnt value indicates if timestamps were dropped due to an overflow of the Transmit Timestamp queue. The overflow counter sticks at a value of three if additional timestamps were missed.

Note:
Each Transmit Timestamp information consists of Four reads. TXTS_RDY status (0xD02, Bit-11) is required to be read to access the next available Transmit Timestamp information.

Figure 8-111 PTP_TXTS Register
15141312111098
PTP TX Timestamp
R-0x0
76543210
PTP TX Timestamp
R-0x0
Table 8-113 PTP_TXTS Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP TX TimestampR0x0 PTP Transmit Timestamp:
Reading this register returns the Transmit Timestamp in four 16-bit reads.

8.112 PTP_RXTS Register (Offset = 0xD09) [Reset = 0x0000]

PTP_RXTS is shown in Figure 8-112 and described in Table 8-114.

Return to the Summary Table.

This register provides a mechanism for reading the Receive Timestamp and identification information. The fields are read in the following order:
Timestamp_ns [15:0]

Overflow_cnt[1:0], Timestamp_ns[29:16]

Timestamp_sec[15:0]

Timestamp_sec[31:16]

sequenceId[15:0]

messageType[3:0], source_hash[11:0]

The Overflow_cnt value indicates if timestamps were dropped due to an overflow of the Transmit Timestamp queue. The overflow counter sticks at a value of three if additional timestamps were missed.

Note:
Each Receive Timestamp information consists of Six reads. RXTS_RDY status (0xD02, Bit-12) is required to be read to access the next available Receive Timestamp information.

Figure 8-112 PTP_RXTS Register
15141312111098
PTP RX Timestamp
R-0x0
76543210
PTP RX Timestamp
R-0x0
Table 8-114 PTP_RXTS Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP RX TimestampR0x0 PTP Receive Timestamp:
Reading this register returns the Receive Timestamp and identification information in successive 16-bit reads.

8.113 PTP_ESTS Register (Offset = 0xD0A) [Reset = 0x0000]

PTP_ESTS is shown in Figure 8-113 and described in Table 8-115.

Return to the Summary Table.

This register provides Status for the Event Timestamp unit. Reading this register provides status for the next Event Timestamp contained in the Event Data Register. If this register is 0, no Event Timestamp is available in the Event Data Register. Reading this register automatically moves to the next Event in the queue.

Figure 8-113 PTP_ESTS Register
15141312111098
RESERVEDEvents Missed Counter
R-0x0R-0x0
76543210
Event Timestamp Change LengthEvent Edge DetectedEvent Number DetectedMultiple Events DetectedPTP Event Detected
R-0x0R-0x0R-0x0R-0x0R-0x0
Table 8-115 PTP_ESTS Register Field Descriptions
BitFieldTypeResetDescription
15:11RESERVEDR0x0Reserved
10:8Events Missed CounterR0x0 Number of Events Missed:
Indicates number of events have been missed prior to this timestamp for the EVNT_NUM indicated. This count value sticks at 7 if more than 7 events are missed.
7:6Event Timestamp Change LengthR0x0 Event Timestamp Length:
Indicates length of the Timestamp field in 16-bit words minus 1. Although all fields are available, this indicates how many of the fields contain data different from the previous Event Timestamp. This allows software to avoid reading more significant fields if they have not changed since the previous timestamp. This field is valid for both single and multiple events.
The following shows the number of least significant fields which have new data for each setting
  • 0x0 = One 16-bit field is new (Timestamp_ns[15:0])
  • 0x1 = Two 16-bit fields are new
  • 0x2 = Three 16-bit fields are new
  • 0x3 = All four 16-bit fields are new
5Event Edge DetectedR0x0 Event edge configuration:
Indicates whether the event is a rise or falling event. If the 'Multiple Event Detected' bit is set to 1, this bit indicates the Rise/Fall direction for the event indicated by EVNT_NUM.
  • 0x0 = Falling edge detected
  • 0x1 = Rising edge detected
4:2Event Number DetectedR0x0 Event Number:
Indicates Event Timestamp Unit which detected an event. If the 'Multiple Event Detected' bit is 1, this indicates the lowest event number captured. If events have been missed prior to this timestamp, it indicates the lowest event number captured which had at least one missed event.

1Multiple Events DetectedR0x0 Multiple Event Detect:
Indicates multiple events were detected at the same time. If multiple events are detected, an extended event status field is available as the first data read from the Event Data register.
  • 0x0 = Single event detected
  • 0x1 = Multiple events detected
0PTP Event DetectedR0x0 Indicates an Event has been detected by one of the Event Timestamp Units

8.114 PTP_TRIG Register (Offset = 0xD10) [Reset = 0x0000]

PTP_TRIG is shown in Figure 8-114 and described in Table 8-116.

Return to the Summary Table.


This register provides basic configuration for IEEE 802.1AS Triggers. To write configuration to a trigger, set the TRIG_WR bit along with the TRIG_SEL and other control information. To read configuration from a trigger, set the TRIG_SEL encoding to the trigger desired, and set the TRIG_WR bit to 0. The subsequent read of the PTP_TRIG register returns the configuration information.

Note:
A Pulse is seen in case toggle trigger is set with trig_if_late condition.
In trig_if_late condition, pulse trigger doesnt give pulse of the configured width.

Figure 8-114 PTP_TRIG Register
15141312111098
Trigger Pulse SelectTrigger Periodic EnableTrigger If LateTrigger Notification EnableTrigger GPIO Select
R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
76543210
Trigger Toggle ModeRESERVEDTrigger SelectTrigger Configuration Write
R/W-0x0R-0x0R/W-0x0R/W-0x0
Table 8-116 PTP_TRIG Register Field Descriptions
BitFieldTypeResetDescription
15Trigger Pulse SelectR/W0x0 Trigger Pulse:
Setting this bit causes the trigger to generate a pulse rather than a single rising or falling edge.
14Trigger Periodic EnableR/W0x0 Trigger Periodic:
Setting this bit causes the trigger to generate a periodic signal. If this bit is 0, the trigger generates a single Pulse or Edge depending on the Trigger Control settings.
13Trigger If LateR/W0x0 Trigger-if-late Control:
Setting this bit allows an immediate trigger in the event the trigger is programmed to a time value which is less than the current time. This provides a mechanism for generating an immediate trigger or to immediately begin generating a periodic signal. For a periodic signal, no notification is generated if this bit is set and a late trigger occurs. Only use this function for Trigger 0 or Trigger 1.
This bit has to be programmed before loading the trigger (loading the timestamp).
12Trigger Notification EnableR/W0x0 Trigger Notification Enable:
Setting this bit enables trigger status to be reported on completion of a trigger or on an error detection due to late trigger. If trigger interrupts are enabled, the notification also results in an interrupt being generated.
11:8Trigger GPIO SelectR/W0x0 GPIO trigger output configuration:
Setting this field to a non-zero value connects the trigger to the associated GPIO pin.
  • 0x0 = No GPIO is selected
  • 0x1 = LED_0
  • 0x2 = LED_1
  • 0x3 = RX_ER
7Trigger Toggle ModeR/W0x0 Trigger Toggle mode enable:
Setting this bit puts the trigger into toggle mode. In toggle mode, the initial value is ignored and the trigger output is toggled at the trigger time.
6:4RESERVEDR0x0Reserved
3:1Trigger SelectR/W0x0 Trigger Configuration Select:
This field selects the trigger for configuration read or write.
0Trigger Configuration WriteR/W0x0 Trigger Configuration Write:
Setting this bit generates a Configuration Write to the selected trigger. This bit is self-clear bit and always reads back as 0.

8.115 PTP_EVNT Register (Offset = 0xD11) [Reset = 0x0000]

PTP_EVNT is shown in Figure 8-115 and described in Table 8-117.

Return to the Summary Table.


This register provides basic configuration for IEEE 802.1AS Events. To write configuration to an Event Timestamp Unit, set the EVNT_WR bit along with the EVNT_SEL and other control information. To read configuration from an Event Timestamp Unit, set the EVNT_SEL encoding to the Event desired, and set the EVNT_WR bit to 0. The subsequent read of the PTP_EVNT register returns the configuration information.

Figure 8-115 PTP_EVNT Register
15141312111098
RESERVEDEvent Rise Detect EnableEvent Fall Detect EnableSingle Event CaptureEvent GPIO Select
R-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
76543210
RESERVEDEvent SelectEvent Configuration Write
R-0x0R/W-0x0R/W-0x0
Table 8-117 PTP_EVNT Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14Event Rise Detect EnableR/W0x0 Event Rise Detect Enable:
Enable detection of a rising edge transition on the selected event input.
13Event Fall Detect EnableR/W0x0 Event Fall Detect Enable:
Enable detection of a falling edge transition on the selected event input.
12Single Event CaptureR/W0x0 Single Event Capture:
Setting this bit to a 1 enables single event capture operation. The EVNT_RISE and EVNT_FALL are cleared upon a valid event timestamp capture.
11:8Event GPIO SelectR/W0x0 GPIO event capture configuration:
Setting this field to a non-zero value connects the event to the associated GPIO pin. This field can also be used to capture events based on trigger outputs or AVB clock outputs
  • 0x0 = No GPIO is selected
  • 0x1 = LED_0
  • 0x2 = LED_1
  • 0x3 = RX_ER
  • 0xB = Trigger 0
  • 0xC = Trigger 1
7:4RESERVEDR0x0Reserved
3:1Event SelectR/W0x0 Event Select:
This field selects the Event Timestamp Unit for configuration read or write.
000b = Event-0
001b = Event-1
010b = Event-2
011b = Event-3
100b = Event-4
101b = Event-5
110b = Event-6
111b = Event-7
0Event Configuration WriteR/W0x0 Event Configuration Write:
Setting this bit generates a Configuration Write to the selected Event Timestamp Unit.

8.116 PTP_TXCFG0 Register (Offset = 0xD12) [Reset = 0x0000]

PTP_TXCFG0 is shown in Figure 8-116 and described in Table 8-118.

Return to the Summary Table.


This register provides configuration for IEEE 802.1AS Transmit Timestamp operation.

Figure 8-116 PTP_TXCFG0 Register
15141312111098
Sync Message One-Step EnableTX TimeStamp Info EnableInsert Delay RequestNTP Timestamp EnableIgnore Two-Step FlagDisable CRC One-StepChecksum Correction One-StepIP Address Filter
R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
76543210
Layer2 Timestamp EnableIPv6 Timestamp EnableIPv4 Timestamp EnablePTP VersionTransmit Timestamp Enable
R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-118 PTP_TXCFG0 Register Field Descriptions
BitFieldTypeResetDescription
15Sync Message One-Step EnableR/W0x0 Sync Message One-Step Enable:
Enable automatic insertion of timestamp into transmit Sync Messages. Device automatically parses message and insert the timestamp in the correct location.
UDP checksum and CRC fields is regenerated.
14TX TimeStamp Info EnableR/W0x0 Enable latching of message type, hash value, sequence id along with Timestamp for transmit event packets and transmit these fields through PSF
13Insert Delay RequestR/W0x0 Insert Delay_Req timestamp in Delay_Resp:
If this bit is set to a 1, the device inserts the timestamp for transmitted Delay_Req messages into inbound Delay_Resp messages. The most recent timestamp is used for any inbound Delay_Resp message. The receive timestamp insertion logic must be enabled through the PTP Receive Configuration registers.
12NTP Timestamp EnableR/W0x0 Enable Timestamping of NTP Packets:
If this bit is set to 0, the device checks the UDP protocol field for a PTP Event message (value 319).
If this bit is set to 1, the device checks the UDP protocol field for an NTP message (value 123). This setting applies to the transmit and receive packet parsing engines.
11Ignore Two-Step FlagR/W0x0 Ignore Two_Step flag for One-Step operation:
If this bit is set to a 0, the device does not insert a timestamp if the Two_Step bit is set in the flags field of the PTP header.
If this bit is set to 1, the device inserts a timestamp independent of the setting of the Two_Step flag.
10Disable CRC One-StepR/W0x0 Disable checking of CRC for One-Step operation:
If this bit is set to a 0, the device forces a CRC error for One-Step operation if the incoming frame has a CRC error.
If this bit is set to a 1, the device sends the One-Step frame with a valid CRC, even if the incoming CRC is invalid.
9Checksum Correction One-StepR/W0x0 Enable UDP Checksum correction for One-Step Operation:
Enables correction of the UDP checksum for messages which include insertion of the timestamp. The checksum is corrected by modifying the last two bytes of the UDP
data. The last two bytes must be transmitted by the MAC as 0s. This control must be set for proper IPv6/UDP One-Step operation. This control has no effect for Layer2 Ethernet messages.
8IP Address FilterR/W0x0 Enable IEEE 802.1AS defined IP address filter:
Enable filtering of UDP/IP Event messages using the IANA assigned IP Destination addresses.
If this bit is set to 1, packets with IP Destination addresses which do not match the IANA assigned addresses is not timestamped. This field affects operation for both IPv4 and IPv6. If this field is set to 0, IP destination addresses is ignored.
7Layer2 Timestamp EnableR/W0x0 Layer2 Timestamp Enable:
Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages.
6IPv6 Timestamp EnableR/W0x0 IPv6 Timestamp Enable:
Enables detection of UDP/IPv6 encapsulated PTP event messages.
5IPv4 Timestamp EnableR/W0x0 IPv4 Timestamp Enable:
Enables detection of UDP/IPv4 encapsulated PTP event messages.
4:1PTP VersionR/W0x0 PTP Version:
Enable Timestamp capture for a specific version of the IEEE 802.1AS specification. This field may be programmed to any value between 1 and 15 and allows support for future versions of the IEEE 802.1AS specification. A value of 0 disables version checking (not recommended).
0Transmit Timestamp EnableR/W0x0 Transmit Timestamp Enable:
Enable Timestamp capture for Transmit.

8.117 PTP_TXCFG1 Register (Offset = 0xD13) [Reset = 0x0000]

PTP_TXCFG1 is shown in Figure 8-117 and described in Table 8-119.

Return to the Summary Table.


This register provides data and mask fields to filter the first byte in a PTP Message. This function is disabled if all the mask bits are set to 0.

Figure 8-117 PTP_TXCFG1 Register
15141312111098
Transmit Byte0 Mask
R/W-0x0
76543210
Transmit Byte0 Data
R/W-0x0
Table 8-119 PTP_TXCFG1 Register Field Descriptions
BitFieldTypeResetDescription
15:8Transmit Byte0 MaskR/W0x0 Byte0 Mask:
Bit mask to be used for matching Byte0 of the PTP Message. A one in any bit enables matching for the associated data bit. If no matching is required, set all bits of the mask to 0
7:0Transmit Byte0 DataR/W0x0 Byte0 Data:
Data to be used for matching Byte0 of the PTP Message.

8.118 PSF_CFG0 Register (Offset = 0xD14) [Reset = 0x4700]

PSF_CFG0 is shown in Figure 8-118 and described in Table 8-120.

Return to the Summary Table.


This register provides configuration for the Phy Status Frame function.

Figure 8-118 PSF_CFG0 Register
15141312111098
RESERVEDPSF Termination Field Addition EnableRESERVEDPSF MAC Source AddressPSF Minimum Preamble
R-0x0R/W-0x1R-0x0R/W-0x0R/W-0x7
76543210
PSF Endian ControlPSF Packet TypePSF Delivery EnablePSF Error Delivery EnablePSF TX Timestamp EnablePSF RX Timestamp EnablePSF Trigger EnablePSF Event Enable
R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-120 PSF_CFG0 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x0Reserved
14PSF Termination Field Addition EnableR/W0x1 1b = Enable addition of termination field for PSF packets
13RESERVEDR0x0Reserved
12:11PSF MAC Source AddressR/W0x0 Phy Status Frame Mac Source Address:
  • 0x0 = Use Mac Address [08 00 17 0B 6B 0F]
  • 0x1 = Use Mac Address [08 00 17 00 00 00]
  • 0x2 = Use Mac Multicast Dest Address
  • 0x3 = Use Mac Address [00 00 00 00 00 00]
10:8PSF Minimum PreambleR/W0x7 Phy Status Frame minimum preamble:
Determines the minimum preamble bytes required for sending packets on the MII interface. TI recommends that this be set to the smallest value the MAC tolerates.
7PSF Endian ControlR/W0x0 Phy Status Frame Endian control:
For each 16-bit field in a Status Message, the data is normally be presented in network byte order (Most significant byte first).
If this bit is set to a 1, the byte data fields is reversed so that the least significant byte is first.
6PSF Packet TypeR/W0x0 This bit controls the type of packet used for Phy Status Frames:
  • 0x0 = Layer2 Ethernet packets
  • 0x1 = IPv4 packets.
5PSF Delivery EnableR/W0x0 Phy Control Frame Read Phy Status Frame enable:
Enable Phy Status Frame delivery of Phy Control Frame read data. Data read through a Phy Control Frame returns in a Phy Status Frame.
4PSF Error Delivery EnableR/W0x0 PSF Error Phy Status Frame enable:
Enable Phy Status Frame delivery of Phy Status Frame Errors. This bit does not independently enable Phy Status Frame operation. One of the other enable bits must be set for Phy Status Frames to be generated.
3PSF TX Timestamp EnableR/W0x0 Transmit Timestamp Phy Status Frame enable:
Enable Phy Status Frame delivery of Transmit Timestamps.
2PSF RX Timestamp EnableR/W0x0 Receive Timestamp Phy Status Frame enable:
Enable Phy Status Frame delivery of Receive Timestamps.
1PSF Trigger EnableR/W0x0 Trigger Phy Status Frame enable:
Enable Phy Status Frame delivery of Trigger Status.
0PSF Event EnableR/W0x0 Event Phy Status Frame enable:
Enable Phy Status Frame delivery of Event Timestamps.

8.119 PTP_RXCFG0 Register (Offset = 0xD15) [Reset = 0x0000]

PTP_RXCFG0 is shown in Figure 8-119 and described in Table 8-121.

Return to the Summary Table.


This register provides configuration for IEEE 802.1AS Receive Timestamp operation.

Figure 8-119 PTP_RXCFG0 Register
15141312111098
Domain Match EnableAlternate Leader Timestamp EnableIP Address Data SelectUser Programmed IP Address Filter EnablePTP Receive Follower OnlyIP Address Filters Enable
R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
76543210
L2 Timetamp EnableIPv6 Timestamp Enable:IPv4 Timestamp Enable:RX PTP VersionReceive Timestamp Enable
R/W-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-121 PTP_RXCFG0 Register Field Descriptions
BitFieldTypeResetDescription
15Domain Match EnableR/W0x0 Domain Match Enable:
If set to 1, the Receive Timestamp unit requires the domain Number field (octet 4) of the PTP Header to match the value programmed in the PTP_DOMAIN field
of the PTP_RXCFG3 register. If set to 0, the Receive Timestamp ignores the PTP_DOMAIN field.
14Alternate Leader Timestamp EnableR/W0x0 Alternate Leader Timestamp Disable:
Disables Timestamp generation if the Alternate_Leader flag is set.
  • 0x0 = Ignore Alternate_Leader flag
  • 0x1 = Do not generate Timestamp if Alternate_Leader is 1
13IP Address Data SelectR/W0x0 IP Address data select:
Selects portion of IP address accessible through the PTP_RXCFG2 register.
  • 0x0 = Two Most Significant Octets
  • 0x1 = Two Least Significant Octets
12User Programmed IP Address Filter EnableR/W0x0
Enable User-programmed IP address filter:
Enable detection of UDP/IP Event messages using a programmable IP address. The IP Address is set using the PTP_RXCFG2 register.

11PTP Receive Follower OnlyR/W0x0 Receive Follower Only:
By default, the Receive Timestamp Unit provides Timestamps for event messages meeting other requirements. Setting this bit to a 1 prevents Delay_Req messages from being Timestamped by requiring that the Control Field (offset 32 in the PTP message) be set to a value other than 1.
10:8IP Address Filters EnableR/W0x0 Enable IEEE 802.1AS defined IP address filters:
Enable detection of UDP/IP Event messages using the IANA assigned IP Destination addresses. This field affects operation for both IPv4 and IPv6.
A Timestamp is captured for the PTP message if the IP destination address matches the following:
bxx1 : Dest IP address is 224.0.1.129
bx1x : Dest IP address is 224.0.1.130 - 132
b1xx : Dest IP address is 224.0.0.107
7L2 Timetamp EnableR/W0x0 Layer2 Timestamp Enable:
Enables detection of IEEE 802.3/Ethernet encapsulated PTP event messages.
6IPv6 Timestamp Enable:R/W0x0 IPv6 Timestamp Enable:
Enables detection of UDP/IPv6 encapsulated PTP event messages.
5IPv4 Timestamp Enable:R/W0x0 IPv4 Timestamp Enable:
Enables detection of UDP/IPv4 encapsulated PTP event messages.
4:1RX PTP VersionR/W0x0 PTP Version:
Enable Timestamp capture for a specific version of the IEEE 802.1AS specification. This field may be programmed to any value between 1 and 15 and allows support for future versions of the IEEE 802.1AS specification. A value of 0 disables version checking (not recommended).
0Receive Timestamp EnableR/W0x0 Receive Timestamp Enable:
Enable Timestamp capture for Receive.

8.120 PTP_RXCFG1 Register (Offset = 0xD16) [Reset = 0x0000]

PTP_RXCFG1 is shown in Figure 8-120 and described in Table 8-122.

Return to the Summary Table.


This register provides data and mask fields to filter the first byte in a PTP Message. This function is disabled if all the mask bits are set to 0.

Figure 8-120 PTP_RXCFG1 Register
15141312111098
Receive Byte0 Mask
R/W-0x0
76543210
Receive Byte0 Data
R/W-0x0
Table 8-122 PTP_RXCFG1 Register Field Descriptions
BitFieldTypeResetDescription
15:8Receive Byte0 MaskR/W0x0 Byte0 Mask:
Bit mask to be used for matching Byte0 of the Receive PTP Message. A one in any bit enables matching for the associated data bit. If no matching is required, set all bits of the mask to 0.
7:0Receive Byte0 DataR/W0x0 Byte0 Data:
Data to be used for matching Byte0 of the Receive PTP Message.

8.121 PTP_RXCFG2 Register (Offset = 0xD17) [Reset = 0x0000]

PTP_RXCFG2 is shown in Figure 8-121 and described in Table 8-123.

Return to the Summary Table.


This register provides for programming an IP address to be used for filtering packets to detect PTP Event Messages. Since the IPv4 address is 32-bits, to write an IP address, software must write two 16-bit values. The USER_IP_SEL bit in the PTP_RXCFG0 register selects which octect of the IP address are accessible through this register.

For example, to write an IP address of 224.0.1.129, software should do the following:

1. Set USER_IP_SEL bit in PTP_RXCFG0 register to 0

2. Write 0xE000 (224.00) to PTP_RXCFG2

3. Set USER_IP_SEL bit in the PTP_RXCFG0 register to 1

4. Write 0x0181 (01.129) to PTP_RXCFG2

Reading this register returns the IP address field selected by USER_IP_SEL.

Figure 8-121 PTP_RXCFG2 Register
15141312111098
Receive IP Address Data
R/W-0x0
76543210
Receive IP Address Data
R/W-0x0
Table 8-123 PTP_RXCFG2 Register Field Descriptions
BitFieldTypeResetDescription
15:0Receive IP Address DataR/W0x0 Receive IP Address Data:
16-bits of the IP Address field to be read or written. The 'IP Address Data Select' bit in the PTP_RXCFG0 register selects the portion of the IP address is to be read or written.
- 'IP Address Data Select' in RX_CFG0 == 0 -> set MSB 2 bytes of IPv4/IPv6 Addr in PTP_RXCFG2 register in the normal byte format.
- 'IP Address Data Select' in RX_CFG0 == 1 -> set LSB 2 bytes of IPv4/IPv6 Address in PTP_RXCFG2 register in the normal byte format.
When IPv4, the complete ip address can be set, when IPv6 only MSB 2 bytes of the 16 byte address and LSB 2 bytes of the 16 byte address are compared.

8.122 PTP_RXCFG3 Register (Offset = 0xD18) [Reset = 0xC000]

PTP_RXCFG3 is shown in Figure 8-122 and described in Table 8-124.

Return to the Summary Table.


This register provides extended configuration for IEEE 802.1AS Receive Timestamp operation.

Figure 8-122 PTP_RXCFG3 Register
15141312111098
RX Minimum IFG after TimestampTimestamp on Checksum ErrorTimestamp on CRC ErrorRESERVEDInsert Timestamp
R/W-0xCR/W-0x0R/W-0x0R-0x0R/W-0x0
76543210
PTP Domain Matching Value
R/W-0x0
Table 8-124 PTP_RXCFG3 Register Field Descriptions
BitFieldTypeResetDescription
15:12RX Minimum IFG after TimestampR/W0xC Minimum Inter-frame Gap:
When a Timestamp is appended to a PTP Message, the length of the packet may get extended. This could reduce the Inter-frame Gap (IFG) between packets by as much as 8-byte times (6400 ns at 10 Mb, 640 ns at 100 Mb, 64 ns at 1G). This field sets a minimum on the IFG between packets in number of byte times. If the IFG is set larger than the actual IFG, Preamble bytes of the subsequent packet gets dropped. Set this value to the lowest possible value that the attached MAC can support.
11Timestamp on Checksum ErrorR/W0x0 Record Timestamp if UDP Checksum Error:
By default, Timestamps is discarded for packets with UDP Checksum errors. If this bit is set, the Timestamp is made available in the normal manner.
10Timestamp on CRC ErrorR/W0x0 Record Timestamp if CRC Error:
By default, Timestamps is discarded for packets with CRC errors. If this bit is set, the Timestamp is made available in the normal manner.
9RESERVEDR0x0Reserved
8Insert TimestampR/W0x0 Enable Timestamp Insertion:
Enables Timestamp insertion into a packet containing a PTP Event Message. If this bit is set, the Timestamp does not available through the PTP Receive Timestamp register.
7:0PTP Domain Matching ValueR/W0x0 PTP Domain Value:
Value of the PTP Message domainNumber field. If PTP_RXCFG0:DOMAIN_EN is set to 1, the Receive Timestamp unit only captures a Timestamp if the domainNumber
in the receive PTP message matches the value in this field. If the DOMAIN_EN bit is set to 0, the domainNumber field is ignored.

8.123 PTP_RXCFG4 Register (Offset = 0xD19) [Reset = 0x0000]

PTP_RXCFG4 is shown in Figure 8-123 and described in Table 8-125.

Return to the Summary Table.


This register provides extended configuration for IEEE 802.1AS Receive Timestamp operation. Disable Timestamp insertion using (through PTP_RXCFG3[8]) prior to changing any of the fields in this register.

Figure 8-123 PTP_RXCFG4 Register
15141312111098
IPV4 UDP Checksum ModifySeconds Timestamp EnableSeconds Timestamp LengthRX Timestamp nanosec Field Offset
R/W-0x0R/W-0x0R/W-0x0R/W-0x0
76543210
RX Timestamp nanosec Field OffsetRX Timestamp sec Field Offset
R/W-0x0R/W-0x0
Table 8-125 PTP_RXCFG4 Register Field Descriptions
BitFieldTypeResetDescription
15IPV4 UDP Checksum ModifyR/W0x0 Enable IPV4 UDP modification:
When timestamp insertion is enabled, this bit controls how UDP checksums are handled for IPV4 PTP event messages.
If set to a 0, the device clears the UDP checksum. If a UDP checksum error is detected the device forces a CRC error.
If set to a 1, the device does not clear the UDP checksum. Instead it generates a 2-byte value to correct the UDP checksum and append this immediately following the
PTP message. If an incoming UDP checksum error is detected, the device causes a UDP checksum error in the modified field. Only use this function if the incoming packets contain two extra bytes of UDP data following the PTP message. Do not enable this for systems using version 1 of the IEEE 802.1AS specification.
14Seconds Timestamp EnableR/W0x0 Enable Timestamp Seconds:
Setting this bit to a 1 enables inserting a seconds field when Timestamp Insertion is enabled. If set to 0, only the nanoseconds portion of the Timestamp is inserted
in the packet. This bit is ignored if 'Insert Timestamp' is 0.
This bit is applicable for insertion of timestamps into PTP.
13:12Seconds Timestamp LengthR/W0x0 Inserted Timestamp Seconds Length:
For a PTP message, this field indicates the length of the Seconds field to be inserted in the PTP message. This field is ignored if 'Insert Timestamp' is 0 or if TS_SEC_EN is 0.
  • 0x0 = Least Significant Byte only of Seconds field
  • 0x1 = Two Least Significant Bytes of Seconds field
  • 0x2 = Three Least Significant Bytes of Seconds field
  • 0x3 = All four Bytes of Seconds field
11:6RX Timestamp nanosec Field OffsetR/W0x0 Receive Timestamp Nanoseconds offset:
This field provides an offset to the Nanoseconds field when inserting a Timestamp into a received PTP message. The offset indicates the byte offset from the beginning of the PTP message. This field is ignored if 'Insert Timestamp' is 0.
5:0RX Timestamp sec Field OffsetR/W0x0 Receive Timestamp Seconds offset:
This field provides an offset to the Seconds field when inserting a Timestamp into a received PTP message. The offset indicates the byte offset from the beginning of the PTP message. This field is ignored if 'Insert Timestamp' is 0.

8.124 PTP_TRDL Register (Offset = 0xD1A) [Reset = 0x0000]

PTP_TRDL is shown in Figure 8-124 and described in Table 8-126.

Return to the Summary Table.


This register contains the low 16-bits of the duration in clock cycles to use the Temporary Rate as programmed in the PTP_RATEH and PTP_RATEL registers. Since the Temporary Rate takes affect upon writing the PTP_RATEL register, program this register before setting the Temporary Rate. This register does not need to be reprogrammed for each use of the Temporary Rate registers.

Figure 8-124 PTP_TRDL Register
15141312111098
Temporary Rate Duration [15:10]
R/W-0x0
76543210
Temporary Rate Duration [15:10]
R/W-0x0
Table 8-126 PTP_TRDL Register Field Descriptions
BitFieldTypeResetDescription
15:0Temporary Rate Duration [15:10]R/W0x0 PTP Temporary Rate Duration Low 16-bits:
This register sets the duration for the Temporary Rate in number of clock cycles. The actual Time duration is dependent on the value of the Temporary Rate.

8.125 PTP_TRDH Register (Offset = 0xD1B) [Reset = 0x0000]

PTP_TRDH is shown in Figure 8-125 and described in Table 8-127.

Return to the Summary Table.


This register contains the high 10-bits of the duration in clock cycles to use the Temporary Rate as programmed in the PTP_RATEH and PTP_RATEL registers. Since the Temporary Rate takes affect upon writing the PTP_RATEL register, program this register before setting the Temporary Rate. This register does not need to be reprogrammed for each use of the Temporary Rate registers.

Figure 8-125 PTP_TRDH Register
15141312111098
RESERVEDTemporary Rate Duration [25:16]
R-0x0R/W-0x0
76543210
Temporary Rate Duration [25:16]
R/W-0x0
Table 8-127 PTP_TRDH Register Field Descriptions
BitFieldTypeResetDescription
15:10RESERVEDR0x0Reserved
9:0Temporary Rate Duration [25:16]R/W0x0 PTP Temporary Rate Duration High 10-bits:
This register sets the duration for the Temporary Rate in number of clock cycles. The actual Time duration is dependent on the value of the Temporary Rate.

8.126 PTP_EVNT_TSU_CFG Register (Offset = 0xD1C) [Reset = 0x0002]

PTP_EVNT_TSU_CFG is shown in Figure 8-126 and described in Table 8-128.

Return to the Summary Table.

This register provides configuration of storage of Event Timestamps and the transmission to Host using PSF

Figure 8-126 PTP_EVNT_TSU_CFG Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRESERVEDFull Trigger Timestamp Storage EnableFull Event Timestamp Storage Enable
R-0x0R-0x0R/W-0x1R/W-0x0
Table 8-128 PTP_EVNT_TSU_CFG Register Field Descriptions
BitFieldTypeResetDescription
15:3RESERVEDR0x0Reserved
2RESERVEDR0x0Reserved
1Full Trigger Timestamp Storage EnableR/W0x1 1b = Enable storing of full timestamp for triggers independent of the change from the previous event timestamp
0Full Event Timestamp Storage EnableR/W0x0 1b = Enable storing of full timestamp for events independent of the change from the previous event timestamp

8.127 PSF_TRIG_TS_EN Register (Offset = 0xD1D) [Reset = 0x0000]

PSF_TRIG_TS_EN is shown in Figure 8-127 and described in Table 8-129.

Return to the Summary Table.

This register enables PHY Status Frame delivery of timestamp corresponding to edges of the generated trigger.

Figure 8-127 PSF_TRIG_TS_EN Register
15141312111098
RESERVED
R-0x0
76543210
Trigger Timestamp PHY Status Frame Enable
R/W-0x0
Table 8-129 PSF_TRIG_TS_EN Register Field Descriptions
BitFieldTypeResetDescription
15:8RESERVEDR0x0Reserved
7:0Trigger Timestamp PHY Status Frame EnableR/W0x0 This enables PHY Status Frame delivery of timestamp corresponding to edges of the generated trigger. Every bit corresponds to an enable for 1 trigger unit as:
8'b00000001: Enables PSF delivery for trigger0 edge timestamp
8'b00000010: Enables PSF delivery for trigger1 edge timestamp
8'b00000100: Enables PSF delivery for trigger2 edge timestamp
8'b00001000: Enables PSF delivery for trigger3 edge timestamp
8'b00010000: Enables PSF delivery for trigger4 edge timestamp
8'b00100000: Enables PSF delivery for trigger5 edge timestamp
8'b01000000: Enables PSF delivery for trigger6 edge timestamp
8'b10000000: Enables PSF delivery for trigger7 edge timestamp

8.128 PTP_COC Register (Offset = 0xD20) [Reset = 0x000A]

PTP_COC is shown in Figure 8-128 and described in Table 8-130.

Return to the Summary Table.


This register provides configuration for the PTP clock-synchronized output divide-by-N clock.

Figure 8-128 PTP_COC Register
15141312111098
RESERVED
R-0x0
76543210
RESERVED
R-0xA
Table 8-130 PTP_COC Register Field Descriptions
BitFieldTypeResetDescription
15:8RESERVEDR0x0Reserved
7:0RESERVEDR0xAReserved

8.129 PSF_CFG1 Register (Offset = 0xD21) [Reset = 0x0000]

PSF_CFG1 is shown in Figure 8-129 and described in Table 8-131.

Return to the Summary Table.


This register provides configuration for the Phy Status Frame function. Specifically, the 16-bit value in this register is used as the first 16-bits of the PTP Header data for the Phy Status Frame.

Figure 8-129 PSF_CFG1 Register
15141312111098
RESERVEDPTP Version Field
R-0x0R/W-0x0
76543210
PTP TransportSpecific FieldPTP Message Type Field
R/W-0x0R/W-0x0
Table 8-131 PSF_CFG1 Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11:8PTP Version FieldR/W0x0 PTP v2 versionPTP field:
This field contains the versionPTP field to be sent in status packets from the Phy to the local MAC using the MII receive data interface.
7:4PTP TransportSpecific FieldR/W0x0 PTP v2 Header transportSpecific field:
This field contains the transportSpecific field to be sent in status packets from the Phy to the local MAC using the MII receive data interface.
3:0PTP Message Type FieldR/W0x0 PTP v2 messageType field:
This field contains the messageType field to be sent in status packets from the Phy to the local MAC using the MII receive data interface.

8.130 PSF_CFG2 Register (Offset = 0xD22) [Reset = 0x0000]

PSF_CFG2 is shown in Figure 8-130 and described in Table 8-132.

Return to the Summary Table.


This register provides configuration for the Phy Status Frame function. Specifically, the 16-bit value in this register is used as the first 16-bits of the IP Source address for an IPv4 Phy Status Frame.

Figure 8-130 PSF_CFG2 Register
15141312111098
IP Source Address 1
R/W-0x0
76543210
IP Source Address 0
R/W-0x0
Table 8-132 PSF_CFG2 Register Field Descriptions
BitFieldTypeResetDescription
15:8IP Source Address 1R/W0x0 Second byte of IP source address:
This field contains the second byte of the IP source address.
7:0IP Source Address 0R/W0x0 First byte of IP source address:
This field contains the most significant byte of the IP source address.

8.131 PSF_CFG3 Register (Offset = 0xD23) [Reset = 0x0000]

PSF_CFG3 is shown in Figure 8-131 and described in Table 8-133.

Return to the Summary Table.


This register provides configuration for the Phy Status Frame function. Specifically, the 16-bit value in this register is used as the second 16-bits of the IP Source address for an IPv4 Phy Status Frame.

Figure 8-131 PSF_CFG3 Register
15141312111098
IP Source Address 3
R/W-0x0
76543210
IP Source Address 2
R/W-0x0
Table 8-133 PSF_CFG3 Register Field Descriptions
BitFieldTypeResetDescription
15:8IP Source Address 3R/W0x0 Fourth byte of IP source address:
This field contains the fourth byte of the IP source address.
7:0IP Source Address 2R/W0x0 Third byte of IP source address:
This field contains the third byte of the IP source address.

8.132 PSF_CFG4 Register (Offset = 0xD24) [Reset = 0x0000]

PSF_CFG4 is shown in Figure 8-132 and described in Table 8-134.

Return to the Summary Table.


This register provides configuration for the Phy Status Frame function. Specifically, the 16-bit value in this register is used to assist in computation of the IP checksum for an IPv4 Phy Status Frame.

Figure 8-132 PSF_CFG4 Register
15141312111098
IP Checksum
R/W-0x0
76543210
IP Checksum
R/W-0x0
Table 8-134 PSF_CFG4 Register Field Descriptions
BitFieldTypeResetDescription
15:0IP ChecksumR/W0x0 IP Checksum:
This field contains a precomputed value of ones-complement addition of all fixed values in the IP Header. The device adds the Total Length and Identification values to generate the final checksum.

8.133 PTP_INTCTL Register (Offset = 0xD26) [Reset = 0x0000]

PTP_INTCTL is shown in Figure 8-133 and described in Table 8-135.

Return to the Summary Table.


This register provides configuration for the IEEE 802.1AS interrupt function, allowing the PTP Interrupt to use any of the GPIO pins.

Figure 8-133 PTP_INTCTL Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDPTP Interrupt GPIO Select
R-0x0R/W-0x0
Table 8-135 PTP_INTCTL Register Field Descriptions
BitFieldTypeResetDescription
15:4RESERVEDR0x0Reserved
3:0PTP Interrupt GPIO SelectR/W0x0 PTP Interrupt GPIO select:
To enable interrupts on a GPIO pin, set this field to the required GPIO.
  • 0x0 = INT_N
  • 0x1 = LED_0
  • 0x2 = LED_1

8.134 PTP_CLKSRC Register (Offset = 0xD27) [Reset = 0x0084]

PTP_CLKSRC is shown in Figure 8-134 and described in Table 8-136.

Return to the Summary Table.


This register provides configuration for the reference clock source driving the IEEE 802.1AS hardware logic. The source clock period is also used by the 802.1AS nanoseconds clock adder to add the proper value every reference clock cycle.

Figure 8-134 PTP_CLKSRC Register
15141312111098
PTP Clock Reference Select-1PTP Ref Clock Division EnablePTP Clock Reference Select-2PTP Ref Clock Division Value
R/W-0x0R/W-0x0R/W-0x0R/W-0x1
76543210
PTP Ref Clock Division ValuePTP Clock Source Period
R/W-0x1R/W-0x4
Table 8-136 PTP_CLKSRC Register Field Descriptions
BitFieldTypeResetDescription
15:14PTP Clock Reference Select-1R/W0x0 PTP Clock Source Select:
Selects among possible sources for the PTP reference clock
Mapping of {PTP Clock Reference Select-1, PTP Clock Reference Select-2} is as follows:
b1000 : External reference from LED_0
b0000 : PLL 250M
b0100 : PLL 125M
b0001 : Recovered 200M
b0101 : Recovered 100M
13PTP Ref Clock Division EnableR/W0x0 Clock division enable:
If set to 1, enables division of the PTP reference clock by a factor of value programmed in CLK_DIV_VAL.
12:11PTP Clock Reference Select-2R/W0x0 PTP Clock Source Select:
Selects among possible sources for the PTP reference clock
Mapping of {PTP Clock Reference Select-1, PTP Clock Reference Select-2} is as follows:
b1000 : External reference from LED_0
b0000 : PLL 250M
b0100 : PLL 125M
b0001 : Recovered 200M
b0101 : Recovered 100M
10:7PTP Ref Clock Division ValueR/W0x1 Clock division divider value:
When the clock source selection is the Divide-by-N using 'PTP Ref Clock Division Enable', these bits are used as the N value.
6:0PTP Clock Source PeriodR/W0x4 PTP Clock Source Period:
This field configures the PTP clock source period in nanoseconds. Program the clock source period as > 2

8.135 PTP_ETYPE Register (Offset = 0xD28) [Reset = 0xF788]

PTP_ETYPE is shown in Figure 8-135 and described in Table 8-137.

Return to the Summary Table.


This register provides the Ethernet Type (Ethertype) field for PTP transport over Ethernet (Layer2).

Figure 8-135 PTP_ETYPE Register
15141312111098
PTP EtherType
R/W-0xF788
76543210
PTP EtherType
R/W-0xF788
Table 8-137 PTP_ETYPE Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP EtherTypeR/W0xF788 PTP EtherType:
This field contains the Ethernet Type field used to detect PTP messages transported over Ethernet layer 2.
Program this register in reverse byte format. For example, the ethertype expected from PTP packets is 0x88F7 so 0xF788 is made as default value.

8.136 PTP_OFF Register (Offset = 0xD29) [Reset = 0x0000]

PTP_OFF is shown in Figure 8-136 and described in Table 8-138.

Return to the Summary Table.


This register provides the byte offset to the PTP message in a Layer2 Ethernet frame.

Figure 8-136 PTP_OFF Register
15141312111098
RESERVED
R-0x0
76543210
PTP Message Field Offset
R/W-0x0
Table 8-138 PTP_OFF Register Field Descriptions
BitFieldTypeResetDescription
15:8RESERVEDR0x0Reserved
7:0PTP Message Field OffsetR/W0x0 PTP Message Offset:
This field contains the offset in bytes to the PTP Message from the preceding header. For Layer2, this the offset from the Ethernet Type Field. For UDP/IP, it is the offset from the end of the UDP Header.

8.137 PTP_RXHASH Register (Offset = 0xD2B) [Reset = 0x0000]

PTP_RXHASH is shown in Figure 8-137 and described in Table 8-139.

Return to the Summary Table.


This register provides configuration for the source identity hash filter of the PTP receive packet parser. If enabled, the receive parse logic delivers a receive timestamp only if the hash function on the ten octet sourcePortIdentity field correctly matches the programmed value. The source identity hash filter does not affect timestamp insertion.

Figure 8-137 PTP_RXHASH Register
15141312111098
RESERVEDReceive Hash EnableReceive Hash
R-0x0R/W-0x0R/W-0x0
76543210
Receive Hash
R/W-0x0
Table 8-139 PTP_RXHASH Register Field Descriptions
BitFieldTypeResetDescription
15:13RESERVEDR0x0Reserved
12Receive Hash EnableR/W0x0 Receive Hash Enable:
Enables filtering of PTP messages based on the hash function on the ten octet sourcePortIdentity field.
11:0Receive HashR/W0x0 Receive Hash:
This field contains the expected source identity hash value for incoming PTP event messages.

8.138 PTP_EVENT_GPIO_SEL Register (Offset = 0xD30) [Reset = 0x0000]

PTP_EVENT_GPIO_SEL is shown in Figure 8-138 and described in Table 8-140.

Return to the Summary Table.


This register provides controls to make which IOs as inputs to enable event timestamping on them.

Figure 8-138 PTP_EVENT_GPIO_SEL Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDGPIO Event Enable
R-0x0R/W-0x0
Table 8-140 PTP_EVENT_GPIO_SEL Register Field Descriptions
BitFieldTypeResetDescription
15:5RESERVEDR0x0Reserved
4:0GPIO Event EnableR/W0x0 GPIO Enable for PTP Event timestamping:
Writing to these registers enables GPIOs for event timestamping by making them inputs
Bit[0] = 1 : LED_0 is set as input
Bit[1] = 1 : LED_1 is set as input
Bit[2] = 1 : RX_ER is set as input

8.139 TX_SMD_GPIO_CTL Register (Offset = 0xD32) [Reset = 0x001F]

TX_SMD_GPIO_CTL is shown in Figure 8-139 and described in Table 8-141.

Return to the Summary Table.


This register controls the parsing of PTP frames with Dual VLAN Tag.

Figure 8-139 TX_SMD_GPIO_CTL Register
15141312111098
Dual VLAN Tag Parse EnableRESERVEDRESERVEDRESERVED
R/W-0x0R-0x0R-0x0R-0x0
76543210
RESERVEDRESERVEDRESERVED
R-0x0R-0x1R-0xF
Table 8-141 TX_SMD_GPIO_CTL Register Field Descriptions
BitFieldTypeResetDescription
15Dual VLAN Tag Parse EnableR/W0x0 1b = Enable parsing of received packets with Dual VLAN tag
14RESERVEDR0x0Reserved
13:9RESERVEDR0x0Reserved
8:5RESERVEDR0x0Reserved
4RESERVEDR0x1Reserved
3:0RESERVEDR0xFReserved

8.140 SCH_CTL_1 Register (Offset = 0xD33) [Reset = 0x0000]

SCH_CTL_1 is shown in Figure 8-140 and described in Table 8-142.

Return to the Summary Table.


Contains LSB 16-bits of step rate used by scheduler for scheduling large PPM adjustments.

Figure 8-140 SCH_CTL_1 Register
15141312111098
Scheduler Step Rate [15:0]
R/W-0x0
76543210
Scheduler Step Rate [15:0]
R/W-0x0
Table 8-142 SCH_CTL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0Scheduler Step Rate [15:0]R/W0x0 Scheduler step rate for scheduling large PPM adjustment lower 16-bits:
Bit 15:0 of 24-bit rate step used by scheduler (applicable only during permanent rate change and micro scheduler is used for rate change in small steps), resolution is 2-32 ns. Calculate clock period from mr_base_freq[31:0] and then using desired step rate value in ppm, calculate step rate in ns. Scale the value by 2-32 to obtain value to programmed to mr_step_rate.

8.141 SCH_CTL_2 Register (Offset = 0xD34) [Reset = 0x0300]

SCH_CTL_2 is shown in Figure 8-141 and described in Table 8-143.

Return to the Summary Table.


Contains MSB 8-bits of step rate used by scheduler for scheduling large PPM adjustments along with bypass options for PTP_PLL and accumulator.

Figure 8-141 SCH_CTL_2 Register
15141312111098
RESERVEDBypass Scheduler for PTP PLLBypass Scheduler for Timer
R-0x0R/W-0x1R/W-0x1
76543210
Scheduler Step Rate [23:16]
R/W-0x0
Table 8-143 SCH_CTL_2 Register Field Descriptions
BitFieldTypeResetDescription
15:10RESERVEDR0x0Reserved
9Bypass Scheduler for PTP PLLR/W0x1 Bypass scheduler for PTP_PLL:
Bypass scheduler controlled rate going to PTP_PLL (applicable only during permanent rate change). When this Bit is set and Bit 8 is not set, scheduler controlled rate adjustment is applied to the timer but PTP_PLL gets total PTP rate adjustment. When this bit as well as Bit 8 is set, scheduler based adjustment is bypassed.
8Bypass Scheduler for TimerR/W0x1 Bypass scheduler for Timer:
Bypass scheduler controlled rate going to timer (applicable only during permanent rate change). When this Bit is set and Bit 9 is not set, scheduler controlled rate adjustment is applied to PTP_PLL but timer gets total PTP rate adjustment. When this bit as well as Bit 9 is set, scheduler based adjustment is bypassed.
7:0Scheduler Step Rate [23:16]R/W0x0 Scheduler step rate for scheduling large PPM adjustment MSB 8-bits:
Bit 23:16 of 24-Bit rate step used by scheduler (applicable only during permanent rate change and when micro scheduler is used for rate change in small steps), resolution is 2-32 ns. Calculate clock period from mr_base_freq[31:0]. Using desired step rate value in ppm, calculate step rate in ns. Scale the value by 2-32 to obtain value to be programmed to mr_step_rate.

8.142 FREQ_CTL_1 Register (Offset = 0xD35) [Reset = 0xCCCD]

FREQ_CTL_1 is shown in Figure 8-142 and described in Table 8-144.

Return to the Summary Table.


Contains LSB 16-bits of Base frequency programmable for PTP_PLL.

Figure 8-142 FREQ_CTL_1 Register
15141312111098
RESERVED
R-0xCCCD
76543210
RESERVED
R-0xCCCD
Table 8-144 FREQ_CTL_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0RESERVEDR0xCCCDReserved

8.143 FREQ_CTL_2 Register (Offset = 0xD36) [Reset = 0xCCCC]

FREQ_CTL_2 is shown in Figure 8-143 and described in Table 8-145.

Return to the Summary Table.


Contains MSB 16-bits of Base frequency programmable for PTP_PLL.

Figure 8-143 FREQ_CTL_2 Register
15141312111098
RESERVED
R-0xCCCC
76543210
RESERVED
R-0xCCCC
Table 8-145 FREQ_CTL_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0RESERVEDR0xCCCCReserved

8.144 PTP_RATEL_ACC_ONLY Register (Offset = 0xD37) [Reset = 0x0000]

PTP_RATEL_ACC_ONLY is shown in Figure 8-144 and described in Table 8-146.

Return to the Summary Table.


Contains LSB 16 bits of accumulator only rate adjustment value.

Figure 8-144 PTP_RATEL_ACC_ONLY Register
15141312111098
PTP Accumulator Rate Control [15:0]
R/W-0x0
76543210
PTP Accumulator Rate Control [15:0]
R/W-0x0
Table 8-146 PTP_RATEL_ACC_ONLY Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Accumulator Rate Control [15:0]R/W0x0 Rate Control value for PTP accumulator:
Writing to this register sets the bits 15:0 of the Rate Control value for PTP accumulator when 0xD38[14] is set. The Rate Control value is in units of 2-32 ns. This rate adjustment is not applied to PTP_PLL. PTP_PLL rate adjustment can still be controlled from registers 0xD04 and 0xD05.

8.145 PTP_RATEH_ACC_ONLY Register (Offset = 0xD38) [Reset = 0x0000]

PTP_RATEH_ACC_ONLY is shown in Figure 8-145 and described in Table 8-147.

Return to the Summary Table.


Contains MSB 10 bits of accumulator only rate adjustment value. Also contains enable and direction of accumulator only rate adjustment.

Figure 8-145 PTP_RATEH_ACC_ONLY Register
15141312111098
PTP Accumulator DirectionPTP Accumulator Mode EnablePTP Accumulator Trate EnableRESERVEDPTP Accumulator Rate Control [25:16]
R/W-0x0R/W-0x0R/W-0x0R-0x0R/W-0x0
76543210
PTP Accumulator Rate Control [25:16]
R/W-0x0
Table 8-147 PTP_RATEH_ACC_ONLY Register Field Descriptions
BitFieldTypeResetDescription
15PTP Accumulator DirectionR/W0x0 PTP Rate ACC only Direction:
The setting of this bit controls whether the device operates at a higher or lower frequency than the reference clock. This direction is applied along with 0xD37 and 0xD38[9:0] only if bit 0xD38[14] is set.
0 : Higher Frequency. The 'PTP Accumulator Rate Control' value is added to the clock on every cycle
1 : Lower Frequency. The 'PTP Accumulator Rate Control' value is subtracted from the clock on every cycle
14PTP Accumulator Mode EnableR/W0x0 PTP Accumulator mode:
Setting this bit makes the PTP accumulator to be incremented according to registers 0xD37 and 0xD38[9:0] every clock cycle.
  • 0x0 = accumulation value from 0xD04, 0xD05
  • 0x1 = accumulation value from 0xD37, 0xD38[9:0]
13PTP Accumulator Trate EnableR/W0x0 PTP Temporary Rate Enable in Accumulator Mode:
Setting this bit applies the temporary rate adjustments to the PTP Accumulator too (apart from the PTP PLL)
  • 0x0 = Temporary Rate Adjustments are not applied to PTP Accumulator when Accumulator mode is enabled
  • 0x1 = Temporary Rate Adjustments are applied to PTP Accumulator when Accumulator mode is enabled
12:10RESERVEDR0x0Reserved
9:0PTP Accumulator Rate Control [25:16]R/W0x0 PTP Rate ACC only high 10-bits:
Writing to this register sets the bits 25:16 of the Rate Control value for PTP accumulator when 0xD38[14] is set. The Rate Control value is in units of 2-32 ns. This rate adjustment does not applied to PTP_PLL. PTP_PLL rate adjustment is still controlled from registers 0xD04 and 0xD05.

8.146 PTP_PLL_CTL Register (Offset = 0xD39) [Reset = 0x0025]

PTP_PLL_CTL is shown in Figure 8-146 and described in Table 8-148.

Return to the Summary Table.


Register to configure PTP_PLL settling time and enables storing of PTP timestamp.

Figure 8-146 PTP_PLL_CTL Register
15141312111098
RESERVEDHalf Rate EnablePTP PLL Phase word [32]
R-0x0R-0x0R-0x0
76543210
Capture PTP TimePTP Scheduler Settle Timer
R/W-0x0R/W-0x25
Table 8-148 PTP_PLL_CTL Register Field Descriptions
BitFieldTypeResetDescription
15:10RESERVEDR0x0Reserved
9Half Rate EnableR0x0 PTP_PLL set half rate:
Set half rate for the NCO when in PLL_125M as ref clock mode.
8PTP PLL Phase word [32]R0x0 PTP_PLL phase word bit-32:
Bit 32 of PTP_PLL phase word
7Capture PTP TimeR/W0x0 Capture PTP time and PTP_PLL word:
Used to capture the current 33-bit PTP_PLL word along with 64-bit PTP time. Setting this trigger stores PTP clock timestamp (32-bit seconds accumulator, 32-bit nanosecond accumulator ) and 33-bit PTP_PLL word simultaneously which can be read through 0xD39 - 0xD3F. This bit is self clearing.
6:0PTP Scheduler Settle TimerR/W0x25 PTP_PLL scheduler settle timer:
No of cycles taken by PTP_PLL to provide jitter free output for any change in rate, defines the latency of rate change going to PTP_PLL. Used in scheduler every time the value of the PTP_PLL is changed.

8.147 PTP_PLL_RD_1 Register (Offset = 0xD3A) [Reset = 0x0000]

PTP_PLL_RD_1 is shown in Figure 8-147 and described in Table 8-149.

Return to the Summary Table.


PTP timer nanosec counter readout value.

Figure 8-147 PTP_PLL_RD_1 Register
15141312111098
PTP Timestamp [15:0]
R-0x0
76543210
PTP Timestamp [15:0]
R-0x0
Table 8-149 PTP_PLL_RD_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Timestamp [15:0]R0x0 PTP time nano seconds LSB word:
Bit 15 - 0 of PTP timer nano seconds counter.

8.148 PTP_PLL_RD_2 Register (Offset = 0xD3B) [Reset = 0x0000]

PTP_PLL_RD_2 is shown in Figure 8-148 and described in Table 8-150.

Return to the Summary Table.


PTP timer nanosec counter readout value.

Figure 8-148 PTP_PLL_RD_2 Register
15141312111098
PTP Timestamp [31:16]
R-0x0
76543210
PTP Timestamp [31:16]
R-0x0
Table 8-150 PTP_PLL_RD_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Timestamp [31:16]R0x0 PTP time nano seconds MSB word:
Bit 31 - 16 of PTP timer nano seconds counter.

8.149 PTP_PLL_RD_3 Register (Offset = 0xD3C) [Reset = 0x0000]

PTP_PLL_RD_3 is shown in Figure 8-149 and described in Table 8-151.

Return to the Summary Table.


PTP timer seconds counter readout value.

Figure 8-149 PTP_PLL_RD_3 Register
15141312111098
PTP Timestamp [47:32]
R-0x0
76543210
PTP Timestamp [47:32]
R-0x0
Table 8-151 PTP_PLL_RD_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Timestamp [47:32]R0x0 PTP time seconds LSB word:
Bit 15 - 0 of PTP timer seconds counter.

8.150 PTP_PLL_RD_4 Register (Offset = 0xD3D) [Reset = 0x0000]

PTP_PLL_RD_4 is shown in Figure 8-150 and described in Table 8-152.

Return to the Summary Table.


PTP timer seconds counter readout value.

Figure 8-150 PTP_PLL_RD_4 Register
15141312111098
PTP Timestamp [63:48]
R-0x0
76543210
PTP Timestamp [63:48]
R-0x0
Table 8-152 PTP_PLL_RD_4 Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Timestamp [63:48]R0x0 PTP time seconds MSB word:
Bit 31 - 16 of PTP timer seconds counter.

8.151 PTP_PLL_RD_5 Register (Offset = 0xD3E) [Reset = 0x0000]

PTP_PLL_RD_5 is shown in Figure 8-151 and described in Table 8-153.

Return to the Summary Table.


PTP_PLL phase word read out value.

Figure 8-151 PTP_PLL_RD_5 Register
15141312111098
PTP Timestamp [79:64]
R-0x0
76543210
PTP Timestamp [79:64]
R-0x0
Table 8-153 PTP_PLL_RD_5 Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Timestamp [79:64]R0x0 PTP_PLL phase LSB word:
Bit 15 - 0 of PTP_PLL phase word.

8.152 PTP_PLL_RD_6 Register (Offset = 0xD3F) [Reset = 0x0000]

PTP_PLL_RD_6 is shown in Figure 8-152 and described in Table 8-154.

Return to the Summary Table.


PTP_PLL phase word read out value.

Figure 8-152 PTP_PLL_RD_6 Register
15141312111098
PTP Timestamp [95:80]
R-0x0
76543210
PTP Timestamp [95:80]
R-0x0
Table 8-154 PTP_PLL_RD_6 Register Field Descriptions
BitFieldTypeResetDescription
15:0PTP Timestamp [95:80]R0x0 PTP_PLL phase MSB word:
Bit 31 - 16 of PTP_PLL phase word.

8.153 PTP_ONESTEP_OFF Register (Offset = 0xD40) [Reset = 0x0000]

PTP_ONESTEP_OFF is shown in Figure 8-153 and described in Table 8-155.

Return to the Summary Table.


Controls offset value of onestep timestamp being inserted into the PTP packet.

Figure 8-153 PTP_ONESTEP_OFF Register
15141312111098
PTP Accumulator Rate Control [31:26]PTP One-step Timestamp Offset Addition EnablePTP One-step Timestamp Offset
R/W-0x0R/W-0x0R/W-0x0
76543210
PTP One-step Timestamp Offset
R/W-0x0
Table 8-155 PTP_ONESTEP_OFF Register Field Descriptions
BitFieldTypeResetDescription
15:10PTP Accumulator Rate Control [31:26]R/W0x0 PTP accumulator Rate Control value:
Writing to this register sets bits 31:26 of the Rate Control value for PTP accumulator only when 0xD38[14] is set.
The Rate Control value is in units of 2-32 ns. This rate adjustment is not be applied to PTP_PLL. PTP_PLL rate adjustment is still controlled from registers 0xD04 and 0xD05.
9PTP One-step Timestamp Offset Addition EnableR/W0x0 PTP one-step timestamp offset addition enable:
Setting this bit enables addition of the offset (loaded in 0xD40[8:0]) to the timestamp being inserted into the PTP packet during one-step timestamp insertion
8:0PTP One-step Timestamp OffsetR/W0x0 PTP one-step timestamp offset:
This offset value is added to the timestamp that is being inserted during one-step operation when 0xD40[9] is enabled.

8.154 PTP_PSF_VLAN_CFG_1 Register (Offset = 0xD45) [Reset = 0x0000]

PTP_PSF_VLAN_CFG_1 is shown in Figure 8-154 and described in Table 8-156.

Return to the Summary Table.

Configuration of VLAN tags for PSF packets

Figure 8-154 PTP_PSF_VLAN_CFG_1 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDDual VLAN Tag Enable for PSFVLAN Tag Enable for PSF
R-0x0R/W-0x0R/W-0x0
Table 8-156 PTP_PSF_VLAN_CFG_1 Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0x0Reserved
1Dual VLAN Tag Enable for PSFR/W0x0 1b = Enable addition of dual VLAN tag for PSF packets
0VLAN Tag Enable for PSFR/W0x0 1b = Enable addition of VLAN tag for PSF packet

8.155 PTP_PSF_VLAN_CFG_2 Register (Offset = 0xD46) [Reset = 0x0000]

PTP_PSF_VLAN_CFG_2 is shown in Figure 8-155 and described in Table 8-157.

Return to the Summary Table.

Configuration of VLAN tags for PSF packets

Figure 8-155 PTP_PSF_VLAN_CFG_2 Register
15141312111098
VLAN Tag 1 for PSF
R/W-0x0
76543210
VLAN Tag 1 for PSF
R/W-0x0
Table 8-157 PTP_PSF_VLAN_CFG_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0VLAN Tag 1 for PSFR/W0x0 VLAN Tag 1 added to PSF packets when 0x0D45[0]=1

8.156 PTP_PSF_VLAN_CFG_3 Register (Offset = 0xD47) [Reset = 0x0000]

PTP_PSF_VLAN_CFG_3 is shown in Figure 8-156 and described in Table 8-158.

Return to the Summary Table.

Configuration of VLAN tags for PSF packets

Figure 8-156 PTP_PSF_VLAN_CFG_3 Register
15141312111098
VLAN Tag 2 for PSF
R/W-0x0
76543210
VLAN Tag 2 for PSF
R/W-0x0
Table 8-158 PTP_PSF_VLAN_CFG_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0VLAN Tag 2 for PSFR/W0x0 VLAN Tag 2 added to PSF packets when 0x0D45[1]=1

8.157 MAX_IPV4_LENGTH Register (Offset = 0xD48) [Reset = 0x0724]

MAX_IPV4_LENGTH is shown in Figure 8-157 and described in Table 8-159.

Return to the Summary Table.

Figure 8-157 MAX_IPV4_LENGTH Register
15141312111098
RESERVEDmr_ipv4_length_2
R-0x0R/W-0x1C
76543210
mr_ipv4_length_2mr_ipv4_length_1
R/W-0x1CR/W-0x24
Table 8-159 MAX_IPV4_LENGTH Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11:6mr_ipv4_length_2R/W0x1C Configure max packet length for PSF IPV4. Maximum value of IPv4 packet length is 0x3E
5:0mr_ipv4_length_1R/W0x24 Configure max packet length for PSF IPV4. Maximum value of IPv4 packet length is 0x3E

8.158 PTP_TXCFG_2 Register (Offset = 0xD49) [Reset = 0x0000]

PTP_TXCFG_2 is shown in Figure 8-158 and described in Table 8-160.

Return to the Summary Table.

Figure 8-158 PTP_TXCFG_2 Register
15141312111098
RESERVEDmr_ptp_domain_tx
R-0x0R/W-0x0
76543210
mr_ptp_domain_txmr_pkt_cfg_entx_domain_en
R/W-0x0R/W-0x0R/W-0x0
Table 8-160 PTP_TXCFG_2 Register Field Descriptions
BitFieldTypeResetDescription
15:10RESERVEDR0x0Reserved
9:2mr_ptp_domain_txR/W0x0 Sets ptp domain filtering for Tx packet
1mr_pkt_cfg_enR/W0x0 Sets whether configurability is enabled for DMAC/SMAC in PSF or not
0tx_domain_enR/W0x0 1b = Enable domain filtering on PTP TX
0b=Disable domain filtering on PTP TX

8.159 PSF_DMAC_1 Register (Offset = 0xD4A) [Reset = 0x1B01]

PSF_DMAC_1 is shown in Figure 8-159 and described in Table 8-161.

Return to the Summary Table.

Figure 8-159 PSF_DMAC_1 Register
15141312111098
mr_pkt_sts_ipv4_dmac
R/W-0x1B01
76543210
mr_pkt_sts_ipv4_dmac
R/W-0x1B01
Table 8-161 PSF_DMAC_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_dmacR/W0x1B01 PSF DMAC byte_1 and byte_2 with bytes reversed (byte_2, byte_1)

8.160 PSF_DMAC_2 Register (Offset = 0xD4B) [Reset = 0x0019]

PSF_DMAC_2 is shown in Figure 8-160 and described in Table 8-162.

Return to the Summary Table.

Figure 8-160 PSF_DMAC_2 Register
15141312111098
mr_pkt_sts_ipv4_dmac
R/W-0x19
76543210
mr_pkt_sts_ipv4_dmac
R/W-0x19
Table 8-162 PSF_DMAC_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_dmacR/W0x19 PSF DMAC byte_3 and byte_4 with bytes reversed (byte_4, byte_3)

8.161 PSF_DMAC_3 Register (Offset = 0xD4C) [Reset = 0x0000]

PSF_DMAC_3 is shown in Figure 8-161 and described in Table 8-163.

Return to the Summary Table.

Figure 8-161 PSF_DMAC_3 Register
15141312111098
mr_pkt_sts_ipv4_dmac
R/W-0x0
76543210
mr_pkt_sts_ipv4_dmac
R/W-0x0
Table 8-163 PSF_DMAC_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_dmacR/W0x0 PSF DMAC byte_5 and byte_6 with bytes reversed (byte_6, byte_5)

8.162 PSF_SMAC_1 Register (Offset = 0xD4D) [Reset = 0x0008]

PSF_SMAC_1 is shown in Figure 8-162 and described in Table 8-164.

Return to the Summary Table.

Figure 8-162 PSF_SMAC_1 Register
15141312111098
mr_pkt_sts_ipv4_smac
R/W-0x8
76543210
mr_pkt_sts_ipv4_smac
R/W-0x8
Table 8-164 PSF_SMAC_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_smacR/W0x8 PSF SMAC byte_1 and byte_2 with bytes reversed (byte_2, byte_1)

8.163 PSF_SMAC_2 Register (Offset = 0xD4E) [Reset = 0x0B17]

PSF_SMAC_2 is shown in Figure 8-163 and described in Table 8-165.

Return to the Summary Table.

Figure 8-163 PSF_SMAC_2 Register
15141312111098
mr_pkt_sts_ipv4_smac
R/W-0xB17
76543210
mr_pkt_sts_ipv4_smac
R/W-0xB17
Table 8-165 PSF_SMAC_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_smacR/W0xB17 PSF SMAC byte_3 and byte_4 with bytes reversed (byte_4, byte_3)

8.164 PSF_SMAC_3 Register (Offset = 0xD4F) [Reset = 0x0F6B]

PSF_SMAC_3 is shown in Figure 8-164 and described in Table 8-166.

Return to the Summary Table.

Figure 8-164 PSF_SMAC_3 Register
15141312111098
mr_pkt_sts_ipv4_smac
R/W-0xF6B
76543210
mr_pkt_sts_ipv4_smac
R/W-0xF6B
Table 8-166 PSF_SMAC_3 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_smacR/W0xF6B PSF SMAC byte_5 and byte_6 with bytes reversed (byte_6, byte_5)

8.165 PSF_ETYPE Register (Offset = 0xD50) [Reset = 0xF788]

PSF_ETYPE is shown in Figure 8-165 and described in Table 8-167.

Return to the Summary Table.

Figure 8-165 PSF_ETYPE Register
15141312111098
mr_pkt_sts_ipv4_etype
R/W-0xF788
76543210
mr_pkt_sts_ipv4_etype
R/W-0xF788
Table 8-167 PSF_ETYPE Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_etypeR/W0xF788 PSF ether type byte_1, byte_2 for L2 packet with bytes reversed (byte_2, byte1)

8.166 IPV4_DA_1 Register (Offset = 0xD51) [Reset = 0x00E0]

IPV4_DA_1 is shown in Figure 8-166 and described in Table 8-168.

Return to the Summary Table.

Figure 8-166 IPV4_DA_1 Register
15141312111098
mr_pkt_sts_ipv4_da
R/W-0xE0
76543210
mr_pkt_sts_ipv4_da
R/W-0xE0
Table 8-168 IPV4_DA_1 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_daR/W0xE0 PSF DA byte_1, byte_2 with bytes reversed (byte_2, byte_1)

8.167 IPV4_DA_2 Register (Offset = 0xD52) [Reset = 0x8101]

IPV4_DA_2 is shown in Figure 8-167 and described in Table 8-169.

Return to the Summary Table.

Figure 8-167 IPV4_DA_2 Register
15141312111098
mr_pkt_sts_ipv4_da
R/W-0x8101
76543210
mr_pkt_sts_ipv4_da
R/W-0x8101
Table 8-169 IPV4_DA_2 Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_ipv4_daR/W0x8101 PSF DA byte_3, byte_4 with bytes reversed (byte_4, byte_3)

8.168 PSF_SOURCE_UDP_PORT Register (Offset = 0xD53) [Reset = 0x3F01]

PSF_SOURCE_UDP_PORT is shown in Figure 8-168 and described in Table 8-170.

Return to the Summary Table.

Figure 8-168 PSF_SOURCE_UDP_PORT Register
15141312111098
mr_pkt_sts_udp_s_port
R/W-0x3F01
76543210
mr_pkt_sts_udp_s_port
R/W-0x3F01
Table 8-170 PSF_SOURCE_UDP_PORT Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_udp_s_portR/W0x3F01 PSF S_PORT byte1, byte2 with byte reversed (byte_2, byte_1)

8.169 PSF_DESTINATION_UDP_PORT Register (Offset = 0xD54) [Reset = 0x3F01]

PSF_DESTINATION_UDP_PORT is shown in Figure 8-169 and described in Table 8-171.

Return to the Summary Table.

Figure 8-169 PSF_DESTINATION_UDP_PORT Register
15141312111098
mr_pkt_sts_udp_d_port
R/W-0x3F01
76543210
mr_pkt_sts_udp_d_port
R/W-0x3F01
Table 8-171 PSF_DESTINATION_UDP_PORT Register Field Descriptions
BitFieldTypeResetDescription
15:0mr_pkt_sts_udp_d_portR/W0x3F01 PSF D_PORT byte1, byte2 with byte reversed (byte_2, byte_1)

8.170 PTP_LAT_COMP_CTRL Register (Offset = 0xDE0) [Reset = 0xC000]

PTP_LAT_COMP_CTRL is shown in Figure 8-170 and described in Table 8-172.

Return to the Summary Table.

Figure 8-170 PTP_LAT_COMP_CTRL Register
15141312111098
RESERVED
R-0xC0
76543210
RESERVEDRESERVEDRESERVEDDithering Latency Compensation Enable - Receive pathDithering Latency Compensation Enable - Transmit pathLatency Compensation Enable - Receive pathLatency Compensation Enable - Transmit path
R-0x0R-0x0R-0x0R/W-0x0R/W-0x0R/W-0x0R/W-0x0
Table 8-172 PTP_LAT_COMP_CTRL Register Field Descriptions
BitFieldTypeResetDescription
15:8RESERVEDR0xC0Reserved
7:6RESERVEDR0x0Reserved
5RESERVEDR0x0Reserved
4RESERVEDR0x0Reserved
3Dithering Latency Compensation Enable - Receive pathR/W0x0 Enable fixed latency compensation on the Rx side, when dithering is enabled, for 2-step PTP time stamping
2Dithering Latency Compensation Enable - Transmit pathR/W0x0 Enable fixed latency compensation on the Tx side, when dithering is enabled, for 2-step PTP time stamping
1Latency Compensation Enable - Receive pathR/W0x0 Enable fixed latency compensation on the Rx side, for 2-step PTP time stamping
0Latency Compensation Enable - Transmit pathR/W0x0 Enable fixed latency compensation on the Tx side, for 2-step PTP time stamping

8.171 PTP_DEBUG_SEL Register (Offset = 0xDF0) [Reset = 0x0000]

PTP_DEBUG_SEL is shown in Figure 8-171 and described in Table 8-173.

Return to the Summary Table.

Figure 8-171 PTP_DEBUG_SEL Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDRESERVEDPTP External Reference Support Enable
R-0x0R-0x0R/W-0x0
Table 8-173 PTP_DEBUG_SEL Register Field Descriptions
BitFieldTypeResetDescription
15:2RESERVEDR0x0Reserved
1RESERVEDR0x0Reserved
0PTP External Reference Support EnableR/W0x0 In PTP external reference clock mode, by the default minimum frequency supported is >35 MHz. Set this bit to support lower frequencies (up to 25MHz)

8.172 MMD1_PMA_CTRL_1 Register (Offset = 0x1000) [Reset = 0x0000]

MMD1_PMA_CTRL_1 is shown in Figure 8-172 and described in Table 8-174.

Return to the Summary Table.

Figure 8-172 MMD1_PMA_CTRL_1 Register
15141312111098
PMA ResetRESERVED
R/W-0x0R-0x0
76543210
RESERVEDPMA Loopback
R-0x0R/W-0x0
Table 8-174 MMD1_PMA_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15PMA ResetR/W0x0 1b = PMA reset
14:1RESERVEDR0x0Reserved
0PMA LoopbackR/W0x0 1b = PMA loopback set

8.173 MMD1_PMA_STATUS_1 Register (Offset = 0x1001) [Reset = 0x0000]

MMD1_PMA_STATUS_1 is shown in Figure 8-173 and described in Table 8-175.

Return to the Summary Table.

Figure 8-173 MMD1_PMA_STATUS_1 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDLink StatusRESERVED
R-0x0R-0x0R-0x0
Table 8-175 MMD1_PMA_STATUS_1 Register Field Descriptions
BitFieldTypeResetDescription
15:3RESERVEDR0x0Reserved
1:0RESERVEDR0x0Reserved

8.174 MMD1_PMA_STAUS_2 Register (Offset = 0x1007) [Reset = 0x003D]

MMD1_PMA_STAUS_2 is shown in Figure 8-174 and described in Table 8-176.

Return to the Summary Table.

Figure 8-174 MMD1_PMA_STAUS_2 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVEDPMA PMD Type Selection
R-0x0R-0x3D
Table 8-176 MMD1_PMA_STAUS_2 Register Field Descriptions
BitFieldTypeResetDescription
15:6RESERVEDR0x0Reserved
5:0PMA PMD Type SelectionR0x3D PMA or PMD type selection field
111101b = 100BASE-T1 PMA or PMD

8.175 MMD1_PMA_EXT_ABILITY_1 Register (Offset = 0x100B) [Reset = 0x0800]

MMD1_PMA_EXT_ABILITY_1 is shown in Figure 8-175 and described in Table 8-177.

Return to the Summary Table.

Figure 8-175 MMD1_PMA_EXT_ABILITY_1 Register
15141312111098
RESERVEDExtended AbilitiesRESERVED
R-0x0R-0x1R-0x0
76543210
RESERVED
R-0x0
Table 8-177 MMD1_PMA_EXT_ABILITY_1 Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11Extended AbilitiesR0x1 1b = PMA/PMD has BASE-T1 extended abilities
0b = PMA/PMD does not have BASE-T1 extended abilities
10:0RESERVEDR0x0Reserved

8.176 MMD1_PMA_EXT_ABILITY_2 Register (Offset = 0x1012) [Reset = 0x0001]

MMD1_PMA_EXT_ABILITY_2 is shown in Figure 8-176 and described in Table 8-178.

Return to the Summary Table.

Figure 8-176 MMD1_PMA_EXT_ABILITY_2 Register
15141312111098
RESERVED
R-0x0
76543210
RESERVED100BASE-T1 Ability
R-0x0R-0x1
Table 8-178 MMD1_PMA_EXT_ABILITY_2 Register Field Descriptions
BitFieldTypeResetDescription
15:1RESERVEDR0x0Reserved
0100BASE-T1 AbilityR0x1 1b = PMA/PMD supports 100BASE-T1
0b = PMA/PMD does not support 100BASE-T1

8.177 MMD1_PMA_CTRL_2 Register (Offset = 0x1834) [Reset = 0xX000]

MMD1_PMA_CTRL_2 is shown in Figure 8-177 and described in Table 8-179.

Return to the Summary Table.

Figure 8-177 MMD1_PMA_CTRL_2 Register
15141312111098
RESERVEDLeader Follower ConfigurationRESERVED
R-0x1R/W-0xXR-0x0
76543210
RESERVEDtype selection
R-0x0R-0x0
Table 8-179 MMD1_PMA_CTRL_2 Register Field Descriptions
BitFieldTypeResetDescription
15RESERVEDR0x1Reserved
14Leader Follower ConfigurationR/W0x0 1b = Configure PHY as LEADER
0b = Configure PHY as FOLLOWER
13:4RESERVEDR0x0Reserved
3:0type selectionR0x0 type selection field
0000b = 100Base-T1

8.178 MMD1_PMA_TEST_MODE_CTRL Register (Offset = 0x1836) [Reset = 0x0000]

MMD1_PMA_TEST_MODE_CTRL is shown in Figure 8-178 and described in Table 8-180.

Return to the Summary Table.

Figure 8-178 MMD1_PMA_TEST_MODE_CTRL Register
15141312111098
Compliance Test ModeRESERVED
R/W-0x0R-0x0
76543210
RESERVED
R-0x0
Table 8-180 MMD1_PMA_TEST_MODE_CTRL Register Field Descriptions
BitFieldTypeResetDescription
15:13Compliance Test ModeR/W0x0 100BASE-T1 test mode control
000b = Normal mode operation
001b = Test mode 1
010b = Test mode 2
011b = Reserved
100b = Test mode 4
101b = Test mode 5
110b = Reserved
111b = Reserved
12:0RESERVEDR0x0Reserved

8.179 MMD3_PCS_CTRL_1 Register (Offset = 0x3000) [Reset = 0x0000]

MMD3_PCS_CTRL_1 is shown in Figure 8-179 and described in Table 8-181.

Return to the Summary Table.

Figure 8-179 MMD3_PCS_CTRL_1 Register
15141312111098
PCS ResetPCS LoopbackRESERVEDRX Clock StoppableRESERVED
R/W-0x0R/W-0x0R-0x0R/W-0x0R-0x0
76543210
RESERVED
R-0x0
Table 8-181 MMD3_PCS_CTRL_1 Register Field Descriptions
BitFieldTypeResetDescription
15PCS ResetR/W0x0 Reset bit, Self Clear.
When write to this bit 1:
1. reset the registers (not vendor specific) at MMD3/MMD7.
2. Reset brk_top
Please notice: This register is WSC (write-self-clear) and not read-only!
14PCS LoopbackR/W0x0 This bit is cleared by PCS_Reset
13:11RESERVEDR0x0Reserved
10RX Clock StoppableR/W0x0 RW, reset value = 1.
1= PHY may stop receive clock during LPI
0= Clock not stoppable

Note: this flop implemented at glue logic
9:0RESERVEDR0x0Reserved

8.180 MMD3_PCS_Status_1 Register (Offset = 0x3001) [Reset = 0x0000]

MMD3_PCS_Status_1 is shown in Figure 8-180 and described in Table 8-182.

Return to the Summary Table.

Figure 8-180 MMD3_PCS_Status_1 Register
15141312111098
RESERVEDTX LPI ReceivedRX LPI ReceivedTX LPI IndicationRX LPI Indication
R-0x0RC-0x0RC-0x0R-0x0R-0x0
76543210
RESERVEDTX Clock StoppableRESERVED
R-0x0R-0x0R-0x0
Table 8-182 MMD3_PCS_Status_1 Register Field Descriptions
BitFieldTypeResetDescription
15:12RESERVEDR0x0Reserved
11TX LPI ReceivedRC0x0 1= Tx PCS hs received LPI
0= LPI not received
10RX LPI ReceivedRC0x0 1= Rx PCS hs received LPI
0= LPI not received
9TX LPI IndicationR0x0 1= TX PCS is currently receiving LPI
0= PCS is not currently receiving LPI
8RX LPI IndicationR0x0 1= RX PCS is currently receiving LPI
0= PCS is not currently receiving LPI
7RESERVEDR0x0Reserved
6TX Clock StoppableR0x0 1= the MAC may stop the clock during LPI
0= Clock not stoppable
5:0RESERVEDR0x0Reserved