Inicio Administración de potencia Controladores LED Drivers LED RGB
Inicio
Administración de potencia
Controladores LED
Drivers LED RGB

LM2755

ACTIVO

Controlador LED de bomba de carga con interfaz compatible I2C en microSMD

Haga su pedido ahora
Hoja de datos

Se encuentra disponible una versión más nueva de este producto

open-in-new Comparar alternativas
Funcionalidad similar a la del dispositivo comparado
LP5810 ACTIVO Controlador LED RGBW de 4 canales con I2C y control automático de animación Synchronous boost, lower IQ and smaller size

LM2755

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Number of channels 3 LED current per channel (mA) 25 LED configuration Parallel Program memory No Topology Charge pump, Current Sink Programmable ramp control Yes Vin (min) (V) 2.7 Vin (max) (V) 5.5 Iout (max) (A) 0.09 Features Constant current, Current control, I2C control, Programmable lighting engines Iq (typ) (mA) 1 Shutdown current (ISD) (typ) (µA) 5 Operating temperature range (°C) -30 to 85 Rating Catalog
Number of channels 3 LED current per channel (mA) 25 LED configuration Parallel Program memory No Topology Charge pump, Current Sink Programmable ramp control Yes Vin (min) (V) 2.7 Vin (max) (V) 5.5 Iout (max) (A) 0.09 Features Constant current, Current control, I2C control, Programmable lighting engines Iq (typ) (mA) 1 Shutdown current (ISD) (typ) (µA) 5 Operating temperature range (°C) -30 to 85 Rating Catalog
DSBGA (YFQ) 18 3.57408 mm² (— mm × — mm)
  • 90% Peak Efficiency
  • Total solution size < 13mm2
  • No Inductor Required: Only 4 Inexpensive Ceramic Caps
  • 3 Independently Controlled Constant Current Outputs
  • Programmable Trapezoidal Dimming Waveform on Each Output
  • Programmable Timing Control Via Internal Registers and External Clock Synchronization Input
  • 32 Exponential Dimming Steps with 800:1 Dimming Ratio
  • Programmable Brightness Control via I2C-Compatible Interface
  • Hardware Enable Pin
  • Wide Input Voltage Range: 2.7V to 5.5V
  • Tiny 18-bump Thin DSBGA : 1.8mm x 1.6mm x 0.6mm

All trademarks are the property of their respective owners.

  • 90% Peak Efficiency
  • Total solution size < 13mm2
  • No Inductor Required: Only 4 Inexpensive Ceramic Caps
  • 3 Independently Controlled Constant Current Outputs
  • Programmable Trapezoidal Dimming Waveform on Each Output
  • Programmable Timing Control Via Internal Registers and External Clock Synchronization Input
  • 32 Exponential Dimming Steps with 800:1 Dimming Ratio
  • Programmable Brightness Control via I2C-Compatible Interface
  • Hardware Enable Pin
  • Wide Input Voltage Range: 2.7V to 5.5V
  • Tiny 18-bump Thin DSBGA : 1.8mm x 1.6mm x 0.6mm

All trademarks are the property of their respective owners.

The LM2755 is a charge-pump-based, constant current LED driver capable of driving 3 LEDs with a total output current up to 90mA. The diode current waveforms of each LED can be trapezoidal with timing and level parameters (rise time, fall time, high level, low level, delay, high time, low time) programmed via an I2C-compatible interface. The 32 brightness levels found on the LM2755 are exponentially spaced (as opposed to linearly spaced) to better match the response of the human eye to changing brightness levels.

The device requires only four small and low-cost ceramic capacitors. The LM2755 provides excellent efficiency without the use of an inductor by operating the charge pump in a gain of 3/2 or in a gain of 1. Maximum efficiency is achieved over the input voltage range by actively selecting the proper gain based on the LED forward voltage requirements.

The pre-regulation scheme used by the LM2755 is optimized to ensure low conducted noise on the input. An internal soft-start circuitry eliminates high inrush current at start-up. The LM2755 consumes 3µA (typ.) of supply current in shut-down.

The LM2755 is available in Texas Instruments' tiny 18-bump thin DSBGA package.

The LM2755 is a charge-pump-based, constant current LED driver capable of driving 3 LEDs with a total output current up to 90mA. The diode current waveforms of each LED can be trapezoidal with timing and level parameters (rise time, fall time, high level, low level, delay, high time, low time) programmed via an I2C-compatible interface. The 32 brightness levels found on the LM2755 are exponentially spaced (as opposed to linearly spaced) to better match the response of the human eye to changing brightness levels.

The device requires only four small and low-cost ceramic capacitors. The LM2755 provides excellent efficiency without the use of an inductor by operating the charge pump in a gain of 3/2 or in a gain of 1. Maximum efficiency is achieved over the input voltage range by actively selecting the proper gain based on the LED forward voltage requirements.

The pre-regulation scheme used by the LM2755 is optimized to ensure low conducted noise on the input. An internal soft-start circuitry eliminates high inrush current at start-up. The LM2755 consumes 3µA (typ.) of supply current in shut-down.

The LM2755 is available in Texas Instruments' tiny 18-bump thin DSBGA package.
filter Buscar otro/a Drivers LED RGB
Descargar Ver vídeo con transcripción Video

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 5
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos LM2755 Charge Pump LED Controller with I2C Compatible Interface in DSBGA Package datasheet (Rev. D) 7/03/2013
Informe Common LED Functions and LED Driver Design Considerations 21/09/2020
Nota sobre la aplicación How to Select a RGB LED Driver 8/08/2019
Nota sobre la aplicación LM2755 Charge Pump LED Controller with I2C Compatible Interface in SMD (Rev. A) 30/04/2013
Nota sobre la aplicación Designing Energy-Efficient Handheld Illum Solutions (Rev. A) 30/04/2013

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Encapsulado Pines Símbolos CAD, huellas y modelos 3D
DSBGA (YFQ) 18 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos