제품 상세 정보

Frequency range 76 - 81 GHz Number of receivers 4 Number of transmitters 3 ADC sampling rate (max) (Msps) 45 Interface type MIPI-CSI2, SPI Edge AI enabled No Rating Automotive Operating temperature range (°C) -40 to 140 TI functional safety category Functional Safety-Compliant Power supply solution LP87745-Q1
Frequency range 76 - 81 GHz Number of receivers 4 Number of transmitters 3 ADC sampling rate (max) (Msps) 45 Interface type MIPI-CSI2, SPI Edge AI enabled No Rating Automotive Operating temperature range (°C) -40 to 140 TI functional safety category Functional Safety-Compliant Power supply solution LP87745-Q1
FCCSP (ABL) 161 108.16 mm² 10.4 x 10.4
  • FMCW transceiver
    • Integrated PLL, transmitter, receiver, baseband, and ADC
    • 76GHz to 81GHz coverage with 5GHz available bandwidth
    • Four receive channels
    • Three transmit channels
    • Ultra-accurate chirp engine based on Fractional-N PLL
    • TX power: 13dBm
    • RX noise figure: 13dB
    • Phase noise at 1MHz:
      • –96dBc/Hz (76GHz to 77GHz)
      • –94dBc/Hz (77GHz to 81GHz)
  • Built-in calibration and self-test
    • Built-in firmware (ROM)
    • Self-calibrating system across process and temperature
  • Host interface
    • Control interface with external processor over SPI or I2C interface
    • Data interface with external processor over MIPI D-PHY and CSI2 v1.1
    • Interrupts for Fault Reporting
  • Functional Safety-Compliant
    • Developed for functional safety applications
    • Documentation available to aid ISO 26262 functional safety system design up to ASIL-D
    • Hardware integrity up to ASIL-B
    • Safety-related certification
      • ISO 26262 certified up to ASIL B by TUV SUD
  • AEC-Q100 qualified
  • AWR2243 advanced features
    • Embedded self-monitoring with limited Host processor involvement
    • Complex baseband architecture
    • Option of cascading multiple devices to increase channel count
    • Embedded interference detection capability
  • Power management
    • Built-in LDO Network for enhanced PSRR
    • I/Os support dual voltage 3.3V/1.8V
  • Clock source
    • Supports externally driven clock (square/sine) at 40MHz
    • Supports 40MHz crystal connection with load capacitors
  • Easy hardware design
    • 0.65mm pitch, 161-pin 10.4mm × 10.4mm flip chip BGA package for easy assembly and low-cost PCB design
    • Small solution size
  • Operating Conditions
    • Junction temp range: –40°C to 140°C
  • FMCW transceiver
    • Integrated PLL, transmitter, receiver, baseband, and ADC
    • 76GHz to 81GHz coverage with 5GHz available bandwidth
    • Four receive channels
    • Three transmit channels
    • Ultra-accurate chirp engine based on Fractional-N PLL
    • TX power: 13dBm
    • RX noise figure: 13dB
    • Phase noise at 1MHz:
      • –96dBc/Hz (76GHz to 77GHz)
      • –94dBc/Hz (77GHz to 81GHz)
  • Built-in calibration and self-test
    • Built-in firmware (ROM)
    • Self-calibrating system across process and temperature
  • Host interface
    • Control interface with external processor over SPI or I2C interface
    • Data interface with external processor over MIPI D-PHY and CSI2 v1.1
    • Interrupts for Fault Reporting
  • Functional Safety-Compliant
    • Developed for functional safety applications
    • Documentation available to aid ISO 26262 functional safety system design up to ASIL-D
    • Hardware integrity up to ASIL-B
    • Safety-related certification
      • ISO 26262 certified up to ASIL B by TUV SUD
  • AEC-Q100 qualified
  • AWR2243 advanced features
    • Embedded self-monitoring with limited Host processor involvement
    • Complex baseband architecture
    • Option of cascading multiple devices to increase channel count
    • Embedded interference detection capability
  • Power management
    • Built-in LDO Network for enhanced PSRR
    • I/Os support dual voltage 3.3V/1.8V
  • Clock source
    • Supports externally driven clock (square/sine) at 40MHz
    • Supports 40MHz crystal connection with load capacitors
  • Easy hardware design
    • 0.65mm pitch, 161-pin 10.4mm × 10.4mm flip chip BGA package for easy assembly and low-cost PCB design
    • Small solution size
  • Operating Conditions
    • Junction temp range: –40°C to 140°C

The AWR2243 device is an integrated single-chip FMCW transceiver capable of operation in the 76GHz to 81GHz band. The device enables unprecedented levels of integration in an extremely small form factor. AWR2243 is designed for low power, self-monitored, ultra-accurate radar systems in the automotive space.

The AWR2243 device is a self-contained FMCW transceiver single-chip device that simplifies the implementation of Automotive Radar sensors in the band of 76GHz to 81GHz. The device is built on TI’s low-power 45nm RFCMOS process, which enables a monolithic implementation of a 3TX, 4RX system with built-in PLL and ADC converters. Simple programming model changes can enable a wide variety of sensor implementation (Short, Mid, Long) with the possibility of dynamic reconfiguration for implementing a multimode sensor. Additionally, the device is provided as a complete platform device including reference hardware design, software drivers, sample configurations, API guide, and user documentation.

The AWR2243 device is an integrated single-chip FMCW transceiver capable of operation in the 76GHz to 81GHz band. The device enables unprecedented levels of integration in an extremely small form factor. AWR2243 is designed for low power, self-monitored, ultra-accurate radar systems in the automotive space.

The AWR2243 device is a self-contained FMCW transceiver single-chip device that simplifies the implementation of Automotive Radar sensors in the band of 76GHz to 81GHz. The device is built on TI’s low-power 45nm RFCMOS process, which enables a monolithic implementation of a 3TX, 4RX system with built-in PLL and ADC converters. Simple programming model changes can enable a wide variety of sensor implementation (Short, Mid, Long) with the possibility of dynamic reconfiguration for implementing a multimode sensor. Additionally, the device is provided as a complete platform device including reference hardware design, software drivers, sample configurations, API guide, and user documentation.

다운로드 스크립트와 함께 비디오 보기 비디오

추가 정보

TI 개발자 영역을 방문하여 평가 및 개발을 시작하십시오.

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하세요.
31개 모두 보기
상위 문서 유형 직함 형식 옵션 날짜
* Data sheet AWR2243 Single-Chip 76- to 81-GHz FMCW Transceiver datasheet (Rev. D) PDF | HTML 2024/02/05
* Errata AWR2243 Device Errata Silicon Revisions 1.0 and 1.1 (Rev. C) PDF | HTML 2023/10/05
Application note Getting Started with mmWave Sensors PDF | HTML 2025/03/12
Certificate AWR2243-2X-CAS-EVM EU Declaration of Conformity (DoC) 2025/01/24
Functional safety information Design Guide for Functional Safety Compliant Systems using mmWave Radar Sensors (Rev. A) PDF | HTML 2024/04/04
Functional safety information TUV SUD Functional Safety Certificate for AWR Devices (Rev. A) 2024/01/11
Application note AWR2243 Bootloader Flow (Rev. A) PDF | HTML 2023/05/02
Application note Self-Calibration of mmWave Radar Devices (Rev. C) PDF | HTML 2023/01/11
Application note Interference Mitigation For AWR/IWR Devices (Rev. A) PDF | HTML 2022/09/22
White paper How Radar is Displacing Traditional Technologies PDF | HTML 2022/02/11
Functional safety information Report on the Certificate Z10 088989 0023 Rev. 00 2022/02/04
Application note mmWave Radar Radome Design Guide PDF | HTML 2021/08/17
Application note mmWave Production Testing Overview PDF | HTML 2021/04/10
Application note Cascade Coherency and Phase Shifter Calibration PDF | HTML 2020/11/28
Application note Power Management Optimizations - Low Cost LC Filter Solution (Rev. A) PDF | HTML 2020/11/11
White paper The fundamentals of millimeter wave radar sensors (Rev. A) 2020/08/27
Application note Programming Chirp Parameters in TI Radar Devices (Rev. A) 2020/02/13
Application note AWR1xx and AWR22xx Data Path Programmer’s Guide (Rev. A) 2020/02/13
Design guide Imaging Radar Using Cascaded mmWave Sensor Reference Design (Rev. A) 2019/07/25
Technical article The need for speed – The future of radar processing PDF | HTML 2019/07/17
Technical article Imaging radar: one sensor to rule them all PDF | HTML 2019/07/09
Application note AWR2243 Cascade (Rev. B) PDF | HTML 2019/05/16
Application note MIMO Radar (Rev. A) 2018/07/26
Application note TI mmWave Radar sensor RF PCB Design, Manufacturing and Validation Guide 2018/05/07
Application note CMOS MMIC Ready for Road – A Technology Overview 2018/02/28
White paper Reliability advantages of TI flip-chip BGA packaging 2018/01/25
White paper Moving from legacy 24GHz to state-of-the-art 77GHz radar 2017/10/06
White paper Cities grow smarter through innovative semiconductor technologies 2017/07/07
Application note System Performance Measurement With the mmWave Sensor 2017/05/10
White paper TI smart sensors enable automated driving 2017/04/17
White paper Using a complex-baseband architecture in FMCW radar systems 2017/04/17

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

AWR2243-2X-CAS-EVM — 차량용 4D 이미징 레이더를 위한 2개 장치 mmWave 계단식 평가 모듈

이 차량용 레이더는 캐스케이드형 76GHz~81GHz 레이더 센서 모듈입니다. 여기에는 AWR2243 장치 2개로 이루어진 캐스케이드형 어레이와 AM2732R 레이더 프로세서가 포함되어 있습니다. 이 캐스케이드형 레이더 구성에서는 기본 장치가 20GHz LO(로컬 오실레이터) 신호를 1차 장치와 2차 장치 모두에 분배하여 이 두 장치가 하나의 RF 트랜시버로 작동할 수 있습니다. 이를 통해 최대 6개의 전송(TX)과 8개의 수신(RX) 안테나 요소를 지원할 수 있으므로 MIMO 가상 배열에서 총 48개의 가상 채널을 제공합니다.
사용 설명서: PDF | HTML
TI.com에서 구매할 수 없음
평가 보드

AWR2243BOOST — AWR2243 2세대 76GHz~81GHz 고성능 오토모티브 MMIC 평가 모듈

AWR2243 BoosterPack™ 플러그인 모듈은 단일 칩 AWR2243 mmWave 감지 장치를 위한 사용하기 간편한 평가 보드입니다.

AWR2243BOOST에는 MMWAVE-STUDIO 환경과 DCA1000 실시간 데이터 캡처 어댑터를 사용하여 개발을 시작하는 데 필요한 모든 것이 포함되어 있습니다.

표준 20핀 BoosterPack 플러그인 모듈 헤더는 평가 보드를 광범위한 MCU LaunchPad 개발 키트와 호환되도록 하며 손쉬운 프로토타이핑을 지원합니다.

사용 설명서: PDF | HTML
TI.com에서 구매할 수 없음
평가 보드

DCA1000EVM — 실시간 데이터 캡처 및 스트리밍을 위한 DCA1000 평가 모듈

DCA1000 평가 모듈(EVM)은 TI AWR 및 IWR 레이더 센서 EVM의 2레인 및 4레인 LVDS(저전압 차동 신호) 트래픽에 대한 실시간 데이터 캡처 및 스트리밍을 제공합니다. 데이터는 1Gbps 이더넷을 통해 mmWave Studio 툴을 실행하는 PC로 실시간으로 스트리밍되어 캡처, 시각화를 수행할 수 있으며, 데이터 처리 및 알고리즘 개발을 위해 선택한 애플리케이션에 전달할 수 있습니다.

사용 설명서: PDF
TI.com에서 구매할 수 없음
평가 보드

ALTOS-3P-V2 — TDA4 프로세서에 기반한 Altos 4칩 계단식 이미징 레이더

Altos Radar는 세계 최고의 자동차 애플리케이션용 이미징 레이더 개발자입니다. 

 

Altos V2 는 TI AWR2243 MMIC 및 TDA4 프로세서를 기반으로 하는 4칩 계단식 이미징 레이더 디자인입니다. 맞춤형 12TX 및 16TX 안테나 어레이 설계, 완전한 신호 처리 파이프라인, TI의 TDA4 프로세서에 임베디드 구현, ADAS(첨단 운전자 보조 시스템)를 위한 세계적 수준의 포인트 클라우드 출력을 제공합니다.

 

Altos V2는 4칩 계단식 이미징 레이더의 진정한 기능을 경험하기 위한 훌륭한 출발점입니다. (...)

하드웨어 프로그래밍 도구

HS-3P-77-3D-WGA-LOP-4X4 — HUBER+SUHNER의 ADAS 레이더 센서를 위한 안테나 설계

77GHz 3D 도파관 안테나 4TX 4R - RF 기판 독립형 솔루션 제품군

Huber+SUHNER는 RF 기판 독립 솔루션용으로 설계된 2세대 3D 금속 플라스틱 도파관 안테나를 개발 및 제조하고 있습니다. 독점 인터페이스로 구현된 이 첨단 기술은 125mm2의 소형 포트 영역에서 전체 차량용 77GHz 레이더 대역(76GHz~81GHz)을 포함하는 4TX, 4RX 구성 채널로 차세대 고밀도 LOP(Launch-on-Package) 모놀리식 마이크로파 집적 회로(MMIC)를 지원합니다. 안테나 설계는 MMIC 패키지 크기를 (...)

발송: Huber+Suhner AG
Third-party accessory

GAPW-3P-ANTENNA — GapWaves의 ADAS 레이더 센서용 안테나 설계

Gapwaves offers high-performance, low-loss, and cost-efficient waveguide antennas for short-, mid- and long-range automotive radars and industrial applications. Our antennas feature a flexible design and a compact form factor, robust contact-free PCB integration and support contact-free LoP (...)

발송: Gapwaves
Third-party accessory

VCTR-3P-VX1000 — VX1000 측정 및 보정 인터페이스 하드웨어

VX1000 하드웨어는 CANape와 같은 측정 및 보정 도구가 실행 시간에 영향을 최소한으로 미치면서 뛰어난 성능으로 ECU에 액세스하도록 지원합니다. 이 장치는 차량에서의 사용을 위해 설계되었지만, 테스트 벤치와 실험실에서도 사용할 수 있습니다. VX1000 하드웨어는 확장성이 뛰어나고 폭넓은 포트폴리오를 갖추고 있어 모든 사용 사례에 적합한 솔루션을 제공합니다.
이 시스템은 기본 모듈과 플러그온 장치라는 두 가지 주요 부품으로 구성됩니다. VX1000 제품군은 Sitara 제품군(AM263, AM263P, AM275), (...)

소프트웨어 개발 키트(SDK)

MMWAVE-MCUPLUS-SDK mmWave SDK for AWR2944 and AM2732

The mmWave microcontroller (MCU) plus software development kit (SDK) is a collection of software packages that enable application evaluation and development on TI mmWave sensors. This tool includes the MMWAVE-MCUPLUS-SDK and companion packages to support your design needs.

MMWAVE-MCUPLUS-SDK is a (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

다운로드 옵션
애플리케이션 소프트웨어 및 프레임워크

PVIZ-3P-MIMSO — Provizio 5D MIMSO® 레이더 소프트웨어

Provizio MIMSO는 고해상도 레이더 데이터를 밀도가 높은 고충실도 3D 환경 인식으로 변환하는 레이더 이미징 향상 솔루션입니다. MIMSO는 능동 안테나 아키텍처와 고급 신호 처리 기술을 사용하여 각도 해상도와 포인트 클라우드 밀도를 크게 향상시켜 복잡한 주행 시나리오에서 물체의 감지, 분리 및 추적 성능을 향상시킵니다.
 

이 솔루션은 AWR2944 레이더 센서와 연동되도록 설계되어 개발자가 고성능 레이더 하드웨어와 Provizio의 MIMSO 능동 안테나 및 처리 기술을 함께 활용할 수 있도록 합니다. MIMSO는 (...)

발송: Provizio Ltd
펌웨어

MMWAVE-DFP mmWave device firmware package (DFP) for 1st-generation AWR1243 parts

mmWave –DFP is a device firmware package for TI’s 77GHz RF transceiver devices (AWR1243, AWR2243). This package provides firmware/ROM patches and API that provides seamless control and configuration for the RF operation in real-time from an external host device as well as allow periodic (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

다운로드 옵션
펌웨어

MMWAVE-DFP-2G mmWave device firmware package (DFP) for 2nd-generation AWR2243 parts

mmWave –DFP is a device firmware package for TI’s 77GHz RF transceiver devices (AWR1243, AWR2243). This package provides firmware/ROM patches and API that provides seamless control and configuration for the RF operation in real-time from an external host device as well as allow periodic (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

다운로드 옵션
평가 모듈(EVM)용 GUI

MMWAVE-SENSING-ESTIMATOR-CLOUD mmWave sensing estimator cloud development on TI Resource Explorer

The mmWave Sensing Estimator is a web-based configuration tool for TI radar sensors
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작하기

TI-DEVELOPER-ZONE Start embedded development on your desktop or in the cloud

From evaluation to deployment the TI Developer Zone provides a comprehensive range of software, tools and training to ensure that you have everything you need for each stage of the development process.
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

IDE, 구성, 컴파일러 또는 디버거

CCSTUDIO Code Composer Studio integrated development environment (IDE)

CCStudio™ IDE is part of TI's extensive CCStudio™ development tool ecosystem. It is an integrated development environment (IDE) for TI's microcontrollers, processors, wireless connectivity devices and radar sensors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작 다운로드 옵션
IDE, 구성, 컴파일러 또는 디버거

MMWAVE-STUDIO mmWave studio GUI tools for 1st-generation parts (xWR1243, xWR1443, xWR1642, xWR1843, xWR6843, xWR6443)

MMWAVE-STUDIO is a stand-alone Windows® GUI that provides the ability to configure and control mmWave sensor modules and collect analog-to-digital (ADC) data for offline analysis. ADC data capture is intended to enable evaluation and characterization of radio-frequency (RF) performance, (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

다운로드 옵션
IDE, 구성, 컴파일러 또는 디버거

MMWAVE-STUDIO-2G mmWave studio GUI tools for 2nd-generation parts (xWR2243)

MMWAVE-STUDIO is a stand-alone Windows® GUI that provides the ability to configure and control mmWave sensor modules and collect analog-to-digital (ADC) data for offline analysis. ADC data capture is intended to enable evaluation and characterization of radio-frequency (RF) performance, (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

다운로드 옵션
온라인 교육

RADAR-ACADEMY mmWave Radar Academy

The Radar Academy is a documentation package intended to provide educational resources related to mmWave radar technology
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

소프트웨어 프로그래밍 도구

UNIFLASH UniFlash for most TI microcontrollers (MCUs) and mmWave sensors

UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.

UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작 다운로드 옵션
지원 소프트웨어

RADAR-TOOLBOX Radar evaluation and development support package with example projects, documentation and tools

The Radar Toolbox is a collection of demos, software tools, and documentation designed to assist in the evaluation of TI Radar Devices
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

찾아보기 다운로드 옵션
시뮬레이션 모델

AWR2243 BSDL Model

SPRM755.ZIP (274 KB) - BSDL Model
시뮬레이션 모델

AWR2243 IBIS Model

SPRM754.ZIP (1055 KB) - IBIS Model
설계 툴

MMWAVE-3P-SEARCH — mmWave 레이더 센서 타사 검색 툴

TI는 회사들과 협력하여 TI mmWave 레이더 센서 및 관련 서비스를 사용한 다양한 솔루션을 제공하고 있습니다. 이러한 회사들은 mmWave 레이더를 사용하여 생산 단계로 가는 경로를 가속화할 수 있습니다. 이 검색 툴을 다운로드하여 타사 솔루션을 빠르게 검색하고 필요에 맞는 올바른 타사를 찾아보세요.

TI는 다양한 수준의 요구 사항을 충족하기 위해 3개 카테고리의 타사 솔루션을 정의합니다.

  1. 턴키 모듈
    • 특정 애플리케이션을 위한 완전한 엔드 투 엔드 하드웨어 및 소프트웨어 솔루션입니다. 이러한 솔루션은 생산에 사용할 준비가 (...)
레퍼런스 디자인

TIDEP-01012 — 계단식 mmWave 센서를 사용하는 이미징 레이더 레퍼런스 설계

캐스케이드 개발 키트의 두 가지 주요 사용 사례는 다음과 같습니다.
  1. mmWave Studio 툴을 사용하여 AWR2243 4칩 캐스케이드의 성능을 평가하기 위해 MMWCAS-DSP-EVM을 캡처 카드로 사용하려면 TIDEP-01012 설계 가이드를 참조하세요.
  2. 레이더 실시간 소프트웨어 애플리케이션을 개발하기 위해 MMWCAS-DSP-EVM을 사용하려면 TIDEP-01017 설계 가이드를 참조하세요.

이 레퍼런스 설계는 캐스케이드 이미징 레이더 무선 주파수(RF) 시스템을 사용합니다. 캐스케이드 레이더 장치는 향상된 각도 해상도 성능을 (...)

Design guide: PDF
회로도: PDF
레퍼런스 디자인

TIDA-020047 — 차량용 4D 이미징 레이더를 위한 2개 장치 mmWave 계단식 레퍼런스 디자인

이 오토모티브 레이더 레퍼런스 디자인은 계단식 76GHz~81GHz 레이더 센서 모듈입니다. 여기에는 AWR2243 디바이스의 2개 디바이스 계단식 어레이와 AM2732R 레이더 프로세서가 포함됩니다. 이 계단식 레이더 구성에서는 기본 디바이스가 20GHz LO(로컬 오실레이터) 신호를 1차 및 2차 디바이스 모두에 분배하여 이 두 디바이스가 단일 무선 주파수(RF) 트랜시버로 작동할 수 있습니다. 이를 통해 최대 6개의 전송(TX) 및 8개의 수신(RX) 안테나 요소를 지원할 수 있으며, MIMO(Multiple Input (...)
Design guide: PDF
패키지 CAD 기호, 풋프린트 및 3D 모델
FCCSP (ABL) 161 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상