CDCE949-Q1

활성

2.5V 또는 3.3V LVCMOS 출력을 지원하는 AEC-Q100 프로그래머블 4-PLL VCXO 클록 신시사이저

지금 주문하기

데이터 시트

document-pdfAcrobat CDCE949-Q1: Programmable 4-PLL VCXO Clock Synthesizer With 1.8V, 2.5V, and 3.3V LVCMOS Outputs datasheet (Rev. A) (영어) PDF | HTML

CDCE949-Q1

활성

데이터 시트

지금 주문하기

제품 상세 정보

Number of outputs

9

Output type

LVCMOS

Output frequency (max) (MHz)

230

Core supply voltage (V)

1.8

Output supply voltage (V)

2.5, 3.3

Input type

LVCMOS, XTAL

Operating temperature range (°C)

-40 to 125

Features

I2C, Integrated EEPROM, Pin programmable, Spread-spectrum clocking (SSC)

Rating

Automotive

Number of outputs

9

Output type

LVCMOS

Output frequency (max) (MHz)

230

Core supply voltage (V)

1.8

Output supply voltage (V)

2.5, 3.3

Input type

LVCMOS, XTAL

Operating temperature range (°C)

-40 to 125

Features

I2C, Integrated EEPROM, Pin programmable, Spread-spectrum clocking (SSC)

Rating

Automotive

TSSOP (PW)

24

49.92 mm² (7.8 mm × 6.4 mm)

Qualified for Automotive Applications
Member of Programmable Clock Generator Family
- CDCE913/CDCEL913: 1 PLLs, 3 Outputs
- CDCE925/CDCEL925: 2 PLLs, 5 Outputs
- CDCE937/CDCEL937: 3 PLLs, 7 Outputs
- CDCE949: 4 PLLs, 9 Outputs
In-System Programmability and EEPROM
- Serial Programmable Volatile Register
- Non-Volatile EEPROM to Store Customer Settings
Highly Flexible Clock Driver
- Three User-Definable Control Inputs [S0/S1/S2]; such as SSC-Selection, Frequency Switching, Output Enable or Power Down
- Generates Highly-Accurate Clocks for Video, Audio, USB, IEEE1394, RFID, Generates Common Clock Frequencies Used with TI DaVinci™, OMAP™, DSPs
- BlueTooth™, WLAN, Ethernet and GPS
- Programmable SSC Modulation
- Enables 0ppm Clock Generation
Selectable Output Frequency up to 230MHz
Flexible Input Clocking Concept
- External Crystal: 8MHz to 32MHz
- On-Chip VCXO: Pull-Range ±150ppm
- Single-Ended LVCMOS up to 160MHz
Low-Noise PLL Core
- Integrated PLL Loop Filter Components
- Very Low Period Jitter (typical 60ps)
Separate Output Supply Pins
- 3.3V and 2.5V
1.8V Device Power Supply
Latch-Up Performance Meets 100mAPer JESD 78, Class I
Wide Temperature Range –40°C to 125°C
Packaged in TSSOP
Development and Programming Kit for Ease PLL Design and Programming (TI ClockPro)

Qualified for Automotive Applications
Member of Programmable Clock Generator Family
- CDCE913/CDCEL913: 1 PLLs, 3 Outputs
- CDCE925/CDCEL925: 2 PLLs, 5 Outputs
- CDCE937/CDCEL937: 3 PLLs, 7 Outputs
- CDCE949: 4 PLLs, 9 Outputs
In-System Programmability and EEPROM
- Serial Programmable Volatile Register
- Non-Volatile EEPROM to Store Customer Settings
Highly Flexible Clock Driver
- Three User-Definable Control Inputs [S0/S1/S2]; such as SSC-Selection, Frequency Switching, Output Enable or Power Down
- Generates Highly-Accurate Clocks for Video, Audio, USB, IEEE1394, RFID, Generates Common Clock Frequencies Used with TI DaVinci™, OMAP™, DSPs
- BlueTooth™, WLAN, Ethernet and GPS
- Programmable SSC Modulation
- Enables 0ppm Clock Generation
Selectable Output Frequency up to 230MHz
Flexible Input Clocking Concept
- External Crystal: 8MHz to 32MHz
- On-Chip VCXO: Pull-Range ±150ppm
- Single-Ended LVCMOS up to 160MHz
Low-Noise PLL Core
- Integrated PLL Loop Filter Components
- Very Low Period Jitter (typical 60ps)
Separate Output Supply Pins
- 3.3V and 2.5V
1.8V Device Power Supply
Latch-Up Performance Meets 100mAPer JESD 78, Class I
Wide Temperature Range –40°C to 125°C
Packaged in TSSOP
Development and Programming Kit for Ease PLL Design and Programming (TI ClockPro)

The CDCE949-Q1 is a modular PLL-based low-cost high-performance programmable clock synthesizer, multiplier, and divider. The device generates up to 9 output clocks from a single input frequency. Each output can be programmed in-system for any clock frequency up to 230MHz, using up to four independent configurable PLLs.

The CDCE949-Q1 has separate output supply pins, VDDOUT, of 2.5V to 3.3V.

The input accepts an external crystal or LVCMOS clock signal. If an external crystal is used, an on-chip load capacitor is adequate for most applications. The value of the load capacitor is programmable from 0pF to 20pF. Additionally, an on-chip VCXO is selectable, allowing synchronization of the output frequency to an external control signal, that is, a PWM signal.

The deep M/N divider ratio allows the generation of zero-ppm audio/video, networking (WLAN, BlueTooth™, Ethernet, GPS) or Interface (USB, IEEE1394, Memory Stick) clocks from a reference input frequency, such as 27MHz.

All PLLs support SSC (Spread-Spectrum Clocking). SSC can be Center-Spread or Down-Spread clocking. This technique is common for reducing electro-magnetic interference (EMI).

Based on the PLL frequency and the divider settings, the internal loop-filter components are automatically adjusted to achieve high stability, and to optimize the jitter-transfer characteristics of each PLL.

The device supports non-volatile EEPROM programming for easy customization to the application. The CDCE949-Q1 is preset to a factory-default configuration (see the Default Device Configuration section). The device can be reprogrammed to a different application configuration before PCB assembly, or reprogrammed by in-system programming. All device settings are programmable through the SDA/SCL bus, a 2-wire serial interface.

Three programmable control inputs, S0, S1 and S2, can be used to control various aspects of operation including frequency selection, changing the SSC parameters to lower EMI, PLL bypass, power down, and choosing between low level or 3-state for the output-disable function.

The CDCE949-Q1 operates in a 1.8V environment. The device operates within a temperature range of –40°C to 125°C.