IWR1443

활성

MCU 및 하드웨어 가속기를 통합하는 단일 칩 76GHz~81GHz mmWave 센서

제품 상세 정보

Type IC Frequency range 76 - 81 GHz Number of receivers 4 Number of transmitters 3 ADC sampling rate (ksps) 37500 TX power (dBm) 12 Arm CPU Arm Cortex-R4F at 200 MHz Hardware accelerators Radar hardware accelerator Edge AI enabled Yes Interface type CAN, CSI-2, I2C, LVDS, QSPI, SPI, UART RAM (kByte) 576 Operating temperature range (°C) -40 to 105 Power supply solution LP87702-Q1, LP87745-Q1 Rating Catalog
Type IC Frequency range 76 - 81 GHz Number of receivers 4 Number of transmitters 3 ADC sampling rate (ksps) 37500 TX power (dBm) 12 Arm CPU Arm Cortex-R4F at 200 MHz Hardware accelerators Radar hardware accelerator Edge AI enabled Yes Interface type CAN, CSI-2, I2C, LVDS, QSPI, SPI, UART RAM (kByte) 576 Operating temperature range (°C) -40 to 105 Power supply solution LP87702-Q1, LP87745-Q1 Rating Catalog
FCCSP (ABL) 161 108.16 mm² 10.4 x 10.4
  • FMCW Transceiver
    • Integrated PLL, Transmitter, Receiver, Baseband, and A2D
    • 76- to 81-GHz Coverage With 4-GHz Continuous Bandwidth
    • Four Receive Channels
    • Three Transmit Channels (Two Can be Used Simultaneously)
    • Ultra-Accurate Chirp Engine Based on Fractional-N PLL
    • TX Power: 12 dBm
    • RX Noise Figure:
      • 14 dB (76 to 77 GHz)
      • 15 dB (77 to 81 GHz)
    • Phase Noise at 1 MHz:
      • –95 dBc/Hz (76 to 77 GHz)
      • –93 dBc/Hz (77 to 81 GHz)
  • Built-in Calibration and Self-Test
    • ARM® Cortex®-R4F-Based Radio Control System
    • Built-in Firmware (ROM)
    • Self-calibrating System Across Frequency and Temperature
  • On-Chip Programmable Core for Embedded User Application
    • Integrated Cortex®-R4F Microcontroller Clocked at 200 MHz
    • On-Chip Bootloader Supports Autonomous Mode (Loading User Application From QSPI Flash Memory)
    • Integrated Peripherals
      • Internal Memories With ECC
      • Radar Hardware Accelerator (FFT, Log-magnitude Computations, and others)
      • Integrated Timers (Watch Dog and up to Four 32-Bit or Two 64-Bit Timers)
      • I2C (Master and Slave Modes Supported)
      • Two SPI Ports
      • CAN Port
      • Up to Six General-Purpose ADC Ports
  • High-Speed Data Interface to Support Distributed Applications
  • Host Interface
    • Control Interface With External Processor Over SPI
    • Data Interface With External Processor Over MIPI D-PHY and CSI2 V1.1
    • Interrupts for Fault Reporting
  • IWR1443 Advanced Features
    • Embedded Self-monitoring With No Host Processor Involvement
    • Complex Baseband Architecture
    • Embedded Interference Detection Capability
  • Power Management
    • Built-in LDO Network for Enhanced PSRR
    • I/Os Support Dual Voltage 3.3 V/1.8 V
  • Clock Source
    • Supports External Oscillator at 40 MHz
    • Supports Externally Driven Clock (Square/Sine) at 40 MHz
  • Easy Hardware Design
    • 0.65-mm Pitch, 161-Pin 10.4 mm × 10.4 mm Flip Chip BGA Package for Easy Assembly and Low-Cost PCB Design
    • Small Solution Size
  • Operating Conditions
    • Junction Temp Range: –40°C to 105°C
  • FMCW Transceiver
    • Integrated PLL, Transmitter, Receiver, Baseband, and A2D
    • 76- to 81-GHz Coverage With 4-GHz Continuous Bandwidth
    • Four Receive Channels
    • Three Transmit Channels (Two Can be Used Simultaneously)
    • Ultra-Accurate Chirp Engine Based on Fractional-N PLL
    • TX Power: 12 dBm
    • RX Noise Figure:
      • 14 dB (76 to 77 GHz)
      • 15 dB (77 to 81 GHz)
    • Phase Noise at 1 MHz:
      • –95 dBc/Hz (76 to 77 GHz)
      • –93 dBc/Hz (77 to 81 GHz)
  • Built-in Calibration and Self-Test
    • ARM® Cortex®-R4F-Based Radio Control System
    • Built-in Firmware (ROM)
    • Self-calibrating System Across Frequency and Temperature
  • On-Chip Programmable Core for Embedded User Application
    • Integrated Cortex®-R4F Microcontroller Clocked at 200 MHz
    • On-Chip Bootloader Supports Autonomous Mode (Loading User Application From QSPI Flash Memory)
    • Integrated Peripherals
      • Internal Memories With ECC
      • Radar Hardware Accelerator (FFT, Log-magnitude Computations, and others)
      • Integrated Timers (Watch Dog and up to Four 32-Bit or Two 64-Bit Timers)
      • I2C (Master and Slave Modes Supported)
      • Two SPI Ports
      • CAN Port
      • Up to Six General-Purpose ADC Ports
  • High-Speed Data Interface to Support Distributed Applications
  • Host Interface
    • Control Interface With External Processor Over SPI
    • Data Interface With External Processor Over MIPI D-PHY and CSI2 V1.1
    • Interrupts for Fault Reporting
  • IWR1443 Advanced Features
    • Embedded Self-monitoring With No Host Processor Involvement
    • Complex Baseband Architecture
    • Embedded Interference Detection Capability
  • Power Management
    • Built-in LDO Network for Enhanced PSRR
    • I/Os Support Dual Voltage 3.3 V/1.8 V
  • Clock Source
    • Supports External Oscillator at 40 MHz
    • Supports Externally Driven Clock (Square/Sine) at 40 MHz
  • Easy Hardware Design
    • 0.65-mm Pitch, 161-Pin 10.4 mm × 10.4 mm Flip Chip BGA Package for Easy Assembly and Low-Cost PCB Design
    • Small Solution Size
  • Operating Conditions
    • Junction Temp Range: –40°C to 105°C

The IWR1443 device is an integrated single-chip mmWave sensor based on FMCW radar technology capable of operation in the 76- to 81-GHz band with up to 4 GHz continuous chirp. The device is built with TI’s low-power 45-nm RFCMOS process, and this solution enables unprecedented levels of integration in an extremely small form factor. The IWR1443 is an ideal solution for low-power, self-monitored, ultra-accurate radar systems in the industrial applications such as building automation, factory automation, drones, material handling, traffic monitoring, and surveillance.

The IWR1443 device is a self-contained, single-chip solution that simplifies the implementation of mmWave sensors in the band of 76 to 81 GHz. The IWR1443 includes a monolithic implementation of a 3TX, 4RX system with built-in PLL and A2D converters. The device includes fully configurable hardware accelerator that supports complex FFT and CFAR detection. Additionally, the device includes two ARM R4F-based processor subsystems: one processor subsystem is for master control, and additional algorithms; a second processor subsystem is responsible for front-end configuration, control, and calibration. Simple programming model changes can enable a wide variety of sensor implementation with the possibility of dynamic reconfiguration for implementing a multimode sensor. Additionally, the device is provided as a complete platform solution including reference hardware design, software drivers, sample configurations, API guide, training, and user documentation.

The IWR1443 device is an integrated single-chip mmWave sensor based on FMCW radar technology capable of operation in the 76- to 81-GHz band with up to 4 GHz continuous chirp. The device is built with TI’s low-power 45-nm RFCMOS process, and this solution enables unprecedented levels of integration in an extremely small form factor. The IWR1443 is an ideal solution for low-power, self-monitored, ultra-accurate radar systems in the industrial applications such as building automation, factory automation, drones, material handling, traffic monitoring, and surveillance.

The IWR1443 device is a self-contained, single-chip solution that simplifies the implementation of mmWave sensors in the band of 76 to 81 GHz. The IWR1443 includes a monolithic implementation of a 3TX, 4RX system with built-in PLL and A2D converters. The device includes fully configurable hardware accelerator that supports complex FFT and CFAR detection. Additionally, the device includes two ARM R4F-based processor subsystems: one processor subsystem is for master control, and additional algorithms; a second processor subsystem is responsible for front-end configuration, control, and calibration. Simple programming model changes can enable a wide variety of sensor implementation with the possibility of dynamic reconfiguration for implementing a multimode sensor. Additionally, the device is provided as a complete platform solution including reference hardware design, software drivers, sample configurations, API guide, training, and user documentation.

다운로드 스크립트와 함께 비디오 보기 비디오
수상 경력에 빛나는 센서 지금 사용 가능

IWR1443튼 수상 경력에 빛나는 TI mmWave 센서 포트폴리오에 속합니다. 최근 감사의 말은 다음과 같습니다.

  • CES 2018 혁신상 3개 부문 수상
  • Electronic Products 2017 올해의 센싱 부문 제품
  • 2017 ACE(Annual Creativity in Electronics) 어워드 올해의 센서 부문
  • Elektronik 2018 Reader's Choice 올해의 제품 활성 부품 부문

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하세요.
38개 모두 보기
상위 문서 유형 직함 형식 옵션 날짜
* Data sheet IWR1443 Single-Chip 76- to 81-GHz mmWave Sensor datasheet (Rev. C) PDF | HTML 2018/08/15
* Errata IWR1443 Device Errata, Silicon Revisions 1.0, 2.0, and 3.0 (Rev. C) PDF | HTML 2021/05/28
* User guide IWR14xx/16xx/18xx/68xx/64xx Industrial Radar Family Technical Reference Manual (Rev. E) 2020/06/08
Application note Flash Variants Supported by the mmWave Sensor (Rev. G) PDF | HTML 2024/12/17
Application note Flash Variants Supported by the mmWave Sensor (Rev. E) PDF | HTML 2024/01/24
Application note Interference Mitigation For AWR/IWR Devices (Rev. A) PDF | HTML 2022/09/22
Application note TI mmWave Radar Device Regulatory Compliance Overview (Rev. C) PDF | HTML 2021/12/14
Application note mmWave Radar Radome Design Guide PDF | HTML 2021/08/17
Application note mmWave Radar Sensors: Object Versus Range (Rev. A) 2021/05/10
Application note mmWave Production Testing Overview PDF | HTML 2021/04/10
Application note Power Management Optimizations - Low Cost LC Filter Solution (Rev. A) PDF | HTML 2020/11/11
White paper The fundamentals of millimeter wave radar sensors (Rev. A) 2020/08/27
White paper mmWave radar sensors in robotics applications (Rev. A) 2020/06/22
White paper Machine Learning Powers Autonomous Industrial Systems (Rev. A) 2020/06/17
E-book E-book: An engineer’s guide to industrial robot designs 2020/02/12
White paper Bringing intelligent autonomy to fine motion detection (Rev. A) 2018/12/20
User guide Radar Hardware Accelerator User's Guide (Rev. B) 2018/10/23
Application note mmwave Radar Device ADC Raw Data Capture (Rev. B) 2018/10/23
Technical article Using mmWave sensors for intelligent safety guards in factory automation PDF | HTML 2018/08/23
Application note MIMO Radar (Rev. A) 2018/07/26
Application note Watchdog Timer for mmwave Radar Sensors (Rev. A) 2018/06/08
White paper mmWave radar: Enabling greater intelligent autonomy at the edge 2018/06/06
White paper Robust traffic and intersection monitoring using millimeter wave sensors (Rev. B) 2018/05/17
Application note TI mmWave Radar sensor RF PCB Design, Manufacturing and Validation Guide 2018/05/07
Technical article Catch your breath: Which is a better occupancy detector – mmWave or PIR? PDF | HTML 2018/03/26
User guide Radar Hardware Accelerator User's Guide - Part 2 (Rev. A) 2018/03/13
Technical article The picture of the distance: Detecting range to help mmWave sensors understand the PDF | HTML 2018/02/22
Technical article A smarter world will arrive in waves PDF | HTML 2018/01/09
Technical article mmWave fundamentals: Range, velocity and angle PDF | HTML 2017/11/01
Application note XWR1xxx Power Management Optimizations - Low Cost LC Filter Solution 2017/10/16
White paper Moving from legacy 24GHz to state-of-the-art 77GHz radar 2017/10/06
Application note Adding Flash Read and Write to an Existing mmWave Project 2017/09/25
White paper Cities grow smarter through innovative semiconductor technologies 2017/07/07
User guide Radar Hardware Accelerator User's Guide - Part 1 2017/05/17
Technical article Bringing new intelligence to industrial applications with mmWave sensors PDF | HTML 2017/05/16
More literature TI Resource Explorer (TIREX) mmWave Training Series 2017/05/15
White paper Fluid-level sensing using 77GHz millimeter wave 2017/04/17
Functional safety information Drone safety and productivity enabled by mmWave sensors 2017/04/07

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

DCA1000EVM — 실시간 데이터 캡처 및 스트리밍을 위한 DCA1000 평가 모듈

DCA1000 평가 모듈(EVM)은 TI AWR 및 IWR 레이더 센서 EVM의 2레인 및 4레인 LVDS(저전압 차동 신호) 트래픽에 대한 실시간 데이터 캡처 및 스트리밍을 제공합니다. 데이터는 1Gbps 이더넷을 통해 mmWave Studio 툴을 실행하는 PC로 실시간으로 스트리밍되어 캡처, 시각화를 수행할 수 있으며, 데이터 처리 및 알고리즘 개발을 위해 선택한 애플리케이션에 전달할 수 있습니다.

사용 설명서: PDF
TI.com에서 구매할 수 없음
평가 보드

IWR1443BOOST — 단일 칩 77GHz mmWave 센서용 IWR1443 BoosterPack™ 평가 모듈

IWR1443 BoosterPack™ 플러그 인 모듈은 단일 칩 IWR1443 mmWave 감지 장치를 위한 사용하기 간편한 77GHz mmWave 센서 평가 보드로, TI MCU LaunchPad™ 개발 키트 에코시스템에 직결합니다.

IWR1443BOOST에는 저전력 Arm® Cortex® R4F 프로세서에서 개발을 시작하는 데 필요한 모든 것이 포함되어 있습니다. 평가 보드에는 프로그래밍 및 디버깅을 위한 온보드 에뮬레이션, 온보드 버튼, 간단한 사용자 인터페이스를 신속하게 통합하기 위한 LED가 포함되어 있습니다.

이 키트는 (...)

사용 설명서: PDF
TI.com에서 구매할 수 없음
평가 보드

D3-3P-DESIGNCORE-RADAR — D3 임베디드 DesignCore® 레이더 평가 모듈

D3 임베디드의 미니어처 센서, 센서 평가 보드, 센서 퓨전 장치를 사용하면 TI의 mmWave 레이더 기술을 사용하여 D3 임베디드 레이더 모듈을 빠르게 평가할 수 있습니다. 이러한 센서를 사용하면 산업용 애플리케이션을 위한 레이더 알고리즘을 손쉽게 통합할 수 있습니다. 유연한 60GHz 및 77GHz 모듈에서 미니어처 안테나 온 패키지(AoP) 60GHz 및 77GHz 모듈, 유리 섬유 60GHz(77GHz 향후) 모듈의 미니어처 안테나까지 다양한 제품을 제공합니다.

발송: D3 Embedded
디버그 프로브

TMDSEMU110-U — XDS110 JTAG 디버그 프로브

텍사스 인스트루먼트 XDS110은 TI 임베디드 프로세서를 위한 새로운 디버그 프로브(에뮬레이터)입니다. XDS110은 XDS100 제품군을 대체하면서 하나의 포드로 더 다양한 표준(IEEE1149.1, IEEE1149.7, SWD)을지원합니다. 또한 모든 XDS 디버그 프로브는 ETB(Embedded Trace Buffer)가 포함되어 있는 모든 Arm® 및 DSP 프로세서에서 코어(Core) 및 시스템 트레이스(System Trace)를 지원합니다.  핀을 통한 코어 추적의 경우 XDS560v2 PRO TRACE가 필요합니다.

(...)
사용 설명서: PDF
Download English Version: PDF
TI.com에서 구매할 수 없음
디버그 프로브

TMDSEMU200-U — XDS200 USB 디버그 프로브

XDS200은 TI 임베디드 장치를 디버깅하는 데 사용되는 디버그 프로브(에뮬레이터)입니다. 대부분의 장치의 경우 더욱 저렴한 신형 XDS110(www.ti.com/tool/TMDSEMU110-U)을 사용하실 것을 권장합니다. XDS200은 단일 포드에서 다양한 표준(IEEE1149.1, IEEE1149.7, SWD)을 지원합니다. 모든 XDS 디버그 프로브는 ETB(임베디드 트레이스 버퍼)가 포함되어 있는 모든 Arm® 및 DSP 프로세서에서 코어 및 시스템 트레이스를 지원합니다.

XDS200은 TI 20핀 커넥터(TI 14핀, (...)

TI.com에서 구매할 수 없음
디버그 프로브

TMDSEMU560V2STM-U — XDS560v2 시스템 추적 USB 디버그 프로브

XDS560v2는 디버그 프로브의 XDS560™ 제품군 중 최고의 성능을 가진 제품으로, 기존의 JTAG 표준(IEEE1149.1)과 cJTAG(IEEE1149.7)를 모두 지원합니다. SWD(직렬 와이어 디버그)는 지원하지 않습니다.

모든 XDS 디버그 프로브는 ETB(Embedded Trace Buffer)를 특징으로 하는 모든 ARM 및 DSP 프로세서에서 코어 및 시스템 추적을 지원합니다. 핀을 통한 추적의 경우 XDS560v2 PRO TRACE가 필요합니다.

XDS560v2는 MIPI HSPT 60핀 커넥터(TI 14핀, (...)

TI.com에서 구매할 수 없음
디버그 프로브

TMDSEMU560V2STM-UE — XDS560v2 시스템 추적 USB 및 이더넷 디버그 프로브

The XDS560v2 is the highest performance of the XDS family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7). Note that it does not support serial wire debug (SWD).

All XDS debug probes support Core and System Trace in all ARM and DSP processors that (...)

TI.com에서 구매할 수 없음
디버그 프로브

TMDSEMUPROTRACE — XDS560v2 PRO 추적 리시버 및 디버그 프로브

중요: XDS560v2 PRO TRACE 리시버는 TI 프로세서용 핀 트레이스를 지원하는 레거시 제품입니다. 새 장치의 경우 타사 트레이스 리시버를 사용하실 것을 권장합니다.

XDS560v2 PRO TRACE 리시버는 XDS560v2 시스템 트레이스 제품군(USB 버전, USB 및 이더넷 버전)과 동일한 기능을 지원하며 대형 외부 메모리 버퍼에서 코어 핀 트레이스(명령 및 데이터) 지원을 제공합니다. 일부 TI 장치에서 사용할 수 있는 이 외부 메모리 버퍼는 프로세서 또는 코어에서 실행되는 모든 명령을 캡처하여 임베디드 시스템에서 (...)

TI.com에서 구매할 수 없음
하드웨어 프로그래밍 도구

HS-3P-77-3D-WGA-LOP-4X4 — HUBER+SUHNER의 ADAS 레이더 센서를 위한 안테나 설계

77GHz 3D 도파관 안테나 4TX 4R - RF 기판 독립형 솔루션 제품군

Huber+SUHNER는 RF 기판 독립 솔루션용으로 설계된 2세대 3D 금속 플라스틱 도파관 안테나를 개발 및 제조하고 있습니다. 독점 인터페이스로 구현된 이 첨단 기술은 125mm2의 소형 포트 영역에서 전체 차량용 77GHz 레이더 대역(76GHz~81GHz)을 포함하는 4TX, 4RX 구성 채널로 차세대 고밀도 LOP(Launch-on-Package) 모놀리식 마이크로파 집적 회로(MMIC)를 지원합니다. 안테나 설계는 MMIC 패키지 크기를 (...)

발송: Huber+Suhner AG
Third-party accessory

D3-3P-D3RCM — D3 임베디드 DesignCore® 카메라 시리즈 레거시 카메라 모듈

D3RCM 1.3 MP FPD-Link™ III 카메라는 OmniVision® OV10640 이미지 센서 또는 SONY® IMX390 이미지 센서를 탑재한 견고한 카메라 모듈입니다. 이 제품은 오토모티브 및 성능이 중요한 산업용 애플리케이션을 위해 설계된 TI 프로세서 기반의 D3 임베디드 RVP와 호환됩니다. 이 제품은 뛰어난 열 특성을 가지고 있으며 혹독한 환경 조건을 견딜 수 있습니다. 
호환 하드웨어에는 TI의 TDA2X 및 TDA3X 제품군이 포함되어 있습니다.

발송: D3 Embedded
Third-party accessory

GAPW-3P-ANTENNA — GapWaves의 ADAS 레이더 센서용 안테나 설계

Gapwaves offers high-performance, low-loss, and cost-efficient waveguide antennas for short-, mid- and long-range automotive radars and industrial applications. Our antennas feature a flexible design and a compact form factor, robust contact-free PCB integration and support contact-free LoP (...)

발송: Gapwaves
Third-party accessory

WZ-3P-1000303 — Wellenzahl 유전체 렌즈 HDPE CNC 가공품

RAPIDv3 장착을 위한 PCB 스페이서 포함 RAPIDv3 모듈(60/77/122GHz)용 유전체 렌즈

Third-party accessory

WZ-3P-1001086 — Wellenzahl 유전체 렌즈 PLA 3D 프린팅

   RAPIDv3 장착을 위한 PCB 스페이서 포함 RAPIDv3 모듈(60/77/122GHz)용 유전체 렌즈

소프트웨어 개발 키트(SDK)

MMWAVE-SDK mmWave software development kit (SDK)

The mmWave software development kit (SDK) is a collection of software packages to enable application evaluation and development on TI mmWave sensors. This tool includes the MMWAVE-SDK and companion packages to support your design needs.

The MMWAVE-SDK is a unified software platform for the TI (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작 다운로드 옵션
평가 모듈(EVM)용 GUI

MMWAVE-SENSING-ESTIMATOR-CLOUD mmWave sensing estimator cloud development on TI Resource Explorer

The mmWave Sensing Estimator is a web-based configuration tool for TI radar sensors
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작하기

TI-DEVELOPER-ZONE Start embedded development on your desktop or in the cloud

From evaluation to deployment the TI Developer Zone provides a comprehensive range of software, tools and training to ensure that you have everything you need for each stage of the development process.
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

IDE, 구성, 컴파일러 또는 디버거

CCSTUDIO Code Composer Studio integrated development environment (IDE)

CCStudio™ IDE is part of TI's extensive CCStudio™ development tool ecosystem. It is an integrated development environment (IDE) for TI's microcontrollers, processors, wireless connectivity devices and radar sensors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작 다운로드 옵션
IDE, 구성, 컴파일러 또는 디버거

MMWAVE-STUDIO mmWave studio GUI tools for 1st-generation parts (xWR1243, xWR1443, xWR1642, xWR1843, xWR6843, xWR6443)

MMWAVE-STUDIO is a stand-alone Windows® GUI that provides the ability to configure and control mmWave sensor modules and collect analog-to-digital (ADC) data for offline analysis. ADC data capture is intended to enable evaluation and characterization of radio-frequency (RF) performance, (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

다운로드 옵션
IDE, 구성, 컴파일러 또는 디버거

SYSCONFIG Standalone desktop version of SysConfig

SysConfig is a configuration tool designed to simplify hardware and software configuration challenges to accelerate software development.

SysConfig is available as part of the Code Composer Studio™ integrated development environment as well as a standalone application. Additionally SysConfig (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작 다운로드 옵션
온라인 교육

RADAR-ACADEMY mmWave Radar Academy

The Radar Academy is a documentation package intended to provide educational resources related to mmWave radar technology
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

소프트웨어 프로그래밍 도구

UNIFLASH UniFlash for most TI microcontrollers (MCUs) and mmWave sensors

UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.

UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

시작 다운로드 옵션
지원 소프트웨어

RADAR-TOOLBOX Radar evaluation and development support package with example projects, documentation and tools

The Radar Toolbox is a collection of demos, software tools, and documentation designed to assist in the evaluation of TI Radar Devices
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

찾아보기 다운로드 옵션
시뮬레이션 모델

IWR1443 BSDL Model (Rev. B)

SWRM033B.ZIP (274 KB) - BSDL Model
시뮬레이션 모델

IWR1443 IBIS Model

SWRM029.ZIP (1245 KB) - IBIS Model
계산 툴

SWRM018 IWR1443 Power Estimation Spreadsheet

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

설계 툴

MMWAVE-3P-SEARCH — mmWave 레이더 센서 타사 검색 툴

TI는 회사들과 협력하여 TI mmWave 레이더 센서 및 관련 서비스를 사용한 다양한 솔루션을 제공하고 있습니다. 이러한 회사들은 mmWave 레이더를 사용하여 생산 단계로 가는 경로를 가속화할 수 있습니다. 이 검색 툴을 다운로드하여 타사 솔루션을 빠르게 검색하고 필요에 맞는 올바른 타사를 찾아보세요.

TI는 다양한 수준의 요구 사항을 충족하기 위해 3개 카테고리의 타사 솔루션을 정의합니다.

  1. 턴키 모듈
    • 특정 애플리케이션을 위한 완전한 엔드 투 엔드 하드웨어 및 소프트웨어 솔루션입니다. 이러한 솔루션은 생산에 사용할 준비가 (...)
레퍼런스 디자인

TIDEP-01006 — Sitara™ MPU 및 안테나 온 패키지 mmWave 센서의 ROS를 사용하는 자율 로봇 레퍼런스 설계

이 레퍼런스 설계는 Sitara AM57x 프로세서에서 실행되는 프로세서 SDK Linux와 IWR6843 EVM에서 실행되는 mmWave SDK를 이용한 자율 로봇을 보여줍니다. 이 설계는 ROS(로봇 운영 체제)가 실행되고 전체 시스템 제어를 위한 메인 프로세서인 Sitara AM57x 프로세서에서 mmWave 레이더 센서의 포인트 클라우드 데이터를 처리하는 임베디드 로봇 시스템의 기능을 보여줍니다. 이 설계는 향상된 프로세서 SoC 및 센서를 통합하고 널리 채택된 오픈 소스 소프트웨어 구성 요소를 기반으로 임베디드 로봇 (...)
Design guide: PDF
회로도: PDF
레퍼런스 디자인

TIDEP-0091 — 77GHz 레벨 트랜스미터를 위한 전력 최적화 레퍼런스 디자인

TIDEP-0091은 탱크 잔량 측정 애플리케이션, 변위 센서, 4~20mA 센서 및 최소한의 전력 엔빌로프로 높은 범위를 감지하기 위한 IWR14xx 76~81GHz mmWave 센서의 전력 최적화를 위한 전략을 보여줍니다. 이러한 애플리케이션에서 시스템은 작동 소비 전력보다 낮은 전력을 제공하는 저전압 데이터 라인에서 작동하는 경우가 많습니다. 듀티 사이클은 전력 입력 제한을 충족하기 위해 평균 전력을 줄이는 데 매우 중요합니다. 전력 최적화는 정기적 감지를 위한 IWR14xx 장치의 MSP432 외부 듀티 사이클을 통해 (...)
Design guide: PDF
회로도: PDF
레퍼런스 디자인

TIDEP-01003 — mmWave 센서를 사용한 재실 감지 레퍼런스 설계

이 레퍼런스 설계는 최대 10m 범위 및 ±60도의 FOV(시야)에서 관심 영역을 모니터링하는 재실 감지에 TI mmWave 센서 기술을 사용하는 방법을 보여줍니다. 이 레퍼런스 설계에서는 IWR1443BOOST 평가 모듈(EVM)을 사용하며 완전한 레이더 처리 체인을 IWR1443 장치에 통합합니다. 처리 체인에는 아날로그 레이더 구성, ADC(아날로그-디지털 컨버터) 캡처, 로우 레벨 FFT(고속 푸리에 변환) 및 신호 처리가 포함됩니다.
Design guide: PDF
회로도: PDF
패키지 CAD 기호, 풋프린트 및 3D 모델
FCCSP (ABL) 161 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상