首頁 微控制器 (MCU) 與處理器 Microcontrollers 即時數位電源 MCU
首頁
微控制器 (MCU) 與處理器
Microcontrollers
即時數位電源 MCU
最新

F28377D-SEP

現行

Radiation-tolerant, 32-bit MCU with 800MIPs and dual C28 and CLA cores with 1MB flash

立即訂購
產品規格表
使用指南

F28377D-SEP

現行
產品規格表 立即訂購

產品詳細資料

CPU 2 C28, 2 CLA Frequency (MHz) 200 Flash memory (kByte) 1024 RAM (kByte) 204 ADC type 2 16-bit SAR, 4 16-bit Total processing (MIPS) 800 Features External memory interface, FPU32 UART 4 CAN (#) 2 Sigma-delta filter 8 PWM (Ch) 24 Security Secure storage TI functional safety category Functional Safety-Capable Number of ADC channels 7, 9, 12, 14, 20, 24 Direct memory access (Ch) 12 SPI 8 QEP 24 USB Yes Hardware accelerators Control law accelerator, Floating point unit, Trigonometric math accelerator Edge AI enabled Yes Operating temperature range (°C) -55 to 125 Rating Space Communication interface CAN, I2C, McBSP, SCI, SPI Operating system BareMetal (No OS), FreeRTOS, SafeRTOS Nonvolatile memory (kByte) 1024
CPU 2 C28, 2 CLA Frequency (MHz) 200 Flash memory (kByte) 1024 RAM (kByte) 204 ADC type 2 16-bit SAR, 4 16-bit Total processing (MIPS) 800 Features External memory interface, FPU32 UART 4 CAN (#) 2 Sigma-delta filter 8 PWM (Ch) 24 Security Secure storage TI functional safety category Functional Safety-Capable Number of ADC channels 7, 9, 12, 14, 20, 24 Direct memory access (Ch) 12 SPI 8 QEP 24 USB Yes Hardware accelerators Control law accelerator, Floating point unit, Trigonometric math accelerator Edge AI enabled Yes Operating temperature range (°C) -55 to 125 Rating Space Communication interface CAN, I2C, McBSP, SCI, SPI Operating system BareMetal (No OS), FreeRTOS, SafeRTOS Nonvolatile memory (kByte) 1024
HLQFP (PTP) 176 676 mm² (26 mm × 26 mm)
  • VID - V62/25638
  • Radiation hardened
    • Single Event Latch-up (SEL) immune to 45MeV-cm2/mg at 125°C
    • Total Ionizing Dose (TID) RLAT for every wafer lot up to 30krad (Si)
  • Space enhanced plastic
    • Controlled baseline
    • Gold (Au) wire
    • One assembly/test site
    • One fabrication site
    • Available in extended temperature range(–55°C to 125°C)
    • Extended product life cycle
    • Extended product change notification
    • Product traceability
    • Enhanced mold compound for low outgassing
  • Dual-core architecture
    • Two TMS320C28x 32-bit CPUs
    • 200MHz
    • IEEE 754 single-precision Floating-Point Unit (FPU)
    • Trigonometric Math Unit (TMU)
    • Viterbi/Complex Math Unit (VCU-II)
  • Two programmable Control Law Accelerators (CLAs)
    • 200MHz
    • IEEE 754 single-precision floating-point instructions
    • Executes code independently of main CPU
  • On-chip memory
    • 512KB (256KW) or 1MB (512KW) of flash (ECC-protected)
    • 172KB (86KW) or 204KB (102KW) of RAM (ECC-protected or parity-protected)
    • Dual-zone security supporting third-party development
    • Unique identification number
  • Clock and system control
    • Two internal zero-pin 10MHz oscillators
    • On-chip crystal oscillator
    • Windowed watchdog timer module
    • Missing clock detection circuitry
  • 1.2V core, 3.3V I/O design
  • System peripherals
    • Two External Memory Interfaces (EMIFs) with ASRAM and SDRAM support
    • Dual 6-channel Direct Memory Access (DMA) controllers
    • Up to 169 individually programmable, multiplexed General-Purpose Input/Output (GPIO) pins with input filtering
    • Expanded Peripheral Interrupt controller (ePIE)
    • Multiple Low-Power Mode (LPM) support with external wakeup
  • Communications peripherals
    • USB 2.0 (MAC + PHY)
    • Support for 12-pin 3.3V-compatible Universal Parallel Port (uPP) interface
    • Two Controller Area Network (CAN) modules (pin-bootable)
    • Three high-speed (up to 50MHz) SPI ports (pin-bootable)
    • Two Multichannel Buffered Serial Ports (McBSPs)
    • Four Serial Communications Interfaces (SCI/UART) (pin-bootable)
    • Two I2C interfaces (pin-bootable)
  • Analog subsystem
    • Up to four Analog-to-Digital Converters (ADCs)
      • 16-bit mode
        • 1.1MSPS each (up to 4.4MSPS system throughput)
        • Differential inputs
        • Up to 12 external channels
      • 12-bit mode
        • 3.5MSPS each (up to 14MSPS system throughput)
        • Single-ended inputs
        • Up to 24 external channels
      • Single Sample-and-Hold (S/H) on each ADC
      • Hardware-integrated post-processing of ADC conversions
        • Saturating offset calibration
        • Error from setpoint calculation
        • High, low, and zero-crossing compare, with interrupt capability
        • Trigger-to-sample delay capture
    • Eight windowed comparators with 12-bit Digital-to-Analog Converter (DAC) references
    • Three 12-bit buffered DAC outputs
  • Enhanced control peripherals
    • 24 Pulse Width Modulator (PWM) channels with enhanced features
    • 16 High-Resolution Pulse Width Modulator (HRPWM) channels
      • High resolution on both A and B channels of 8 PWM modules
      • Dead-band support (on both standard and high resolution)
    • Six Enhanced Capture (eCAP) modules
    • Three Enhanced Quadrature Encoder Pulse (eQEP) modules
    • Eight Sigma-Delta Filter Module (SDFM) input channels, 2 parallel filters per channel
      • Standard SDFM data filtering
      • Comparator filter for fast action for out of range
  • Supports defense and aerospace applications
    • Controlled baseline
    • One assembly/test site
    • One fabrication site
    • Extended product lifecycle
    • Product traceability
    • Outgassing test performed per ASTM E595
  • Package:
    • 176-pin PowerPAD™ Thermally Enhanced Low-Profile Quad Flatpack (HLQFP) [PTP suffix]
  • Hardware Built-in Self Test (HWBIST)
  • Temperature:
    • –55°C to 150°C junction
  • VID - V62/25638
  • Radiation hardened
    • Single Event Latch-up (SEL) immune to 45MeV-cm2/mg at 125°C
    • Total Ionizing Dose (TID) RLAT for every wafer lot up to 30krad (Si)
  • Space enhanced plastic
    • Controlled baseline
    • Gold (Au) wire
    • One assembly/test site
    • One fabrication site
    • Available in extended temperature range(–55°C to 125°C)
    • Extended product life cycle
    • Extended product change notification
    • Product traceability
    • Enhanced mold compound for low outgassing
  • Dual-core architecture
    • Two TMS320C28x 32-bit CPUs
    • 200MHz
    • IEEE 754 single-precision Floating-Point Unit (FPU)
    • Trigonometric Math Unit (TMU)
    • Viterbi/Complex Math Unit (VCU-II)
  • Two programmable Control Law Accelerators (CLAs)
    • 200MHz
    • IEEE 754 single-precision floating-point instructions
    • Executes code independently of main CPU
  • On-chip memory
    • 512KB (256KW) or 1MB (512KW) of flash (ECC-protected)
    • 172KB (86KW) or 204KB (102KW) of RAM (ECC-protected or parity-protected)
    • Dual-zone security supporting third-party development
    • Unique identification number
  • Clock and system control
    • Two internal zero-pin 10MHz oscillators
    • On-chip crystal oscillator
    • Windowed watchdog timer module
    • Missing clock detection circuitry
  • 1.2V core, 3.3V I/O design
  • System peripherals
    • Two External Memory Interfaces (EMIFs) with ASRAM and SDRAM support
    • Dual 6-channel Direct Memory Access (DMA) controllers
    • Up to 169 individually programmable, multiplexed General-Purpose Input/Output (GPIO) pins with input filtering
    • Expanded Peripheral Interrupt controller (ePIE)
    • Multiple Low-Power Mode (LPM) support with external wakeup
  • Communications peripherals
    • USB 2.0 (MAC + PHY)
    • Support for 12-pin 3.3V-compatible Universal Parallel Port (uPP) interface
    • Two Controller Area Network (CAN) modules (pin-bootable)
    • Three high-speed (up to 50MHz) SPI ports (pin-bootable)
    • Two Multichannel Buffered Serial Ports (McBSPs)
    • Four Serial Communications Interfaces (SCI/UART) (pin-bootable)
    • Two I2C interfaces (pin-bootable)
  • Analog subsystem
    • Up to four Analog-to-Digital Converters (ADCs)
      • 16-bit mode
        • 1.1MSPS each (up to 4.4MSPS system throughput)
        • Differential inputs
        • Up to 12 external channels
      • 12-bit mode
        • 3.5MSPS each (up to 14MSPS system throughput)
        • Single-ended inputs
        • Up to 24 external channels
      • Single Sample-and-Hold (S/H) on each ADC
      • Hardware-integrated post-processing of ADC conversions
        • Saturating offset calibration
        • Error from setpoint calculation
        • High, low, and zero-crossing compare, with interrupt capability
        • Trigger-to-sample delay capture
    • Eight windowed comparators with 12-bit Digital-to-Analog Converter (DAC) references
    • Three 12-bit buffered DAC outputs
  • Enhanced control peripherals
    • 24 Pulse Width Modulator (PWM) channels with enhanced features
    • 16 High-Resolution Pulse Width Modulator (HRPWM) channels
      • High resolution on both A and B channels of 8 PWM modules
      • Dead-band support (on both standard and high resolution)
    • Six Enhanced Capture (eCAP) modules
    • Three Enhanced Quadrature Encoder Pulse (eQEP) modules
    • Eight Sigma-Delta Filter Module (SDFM) input channels, 2 parallel filters per channel
      • Standard SDFM data filtering
      • Comparator filter for fast action for out of range
  • Supports defense and aerospace applications
    • Controlled baseline
    • One assembly/test site
    • One fabrication site
    • Extended product lifecycle
    • Product traceability
    • Outgassing test performed per ASTM E595
  • Package:
    • 176-pin PowerPAD™ Thermally Enhanced Low-Profile Quad Flatpack (HLQFP) [PTP suffix]
  • Hardware Built-in Self Test (HWBIST)
  • Temperature:
    • –55°C to 150°C junction

C2000™ 32-bit microcontrollers are optimized for processing, sensing, and actuation to improve closed-loop performance in real-time control applications such as industrial motor drives; solar inverters and digital power; electrical vehicles and transportation; motor control; and sensing and signal processing. The C2000 line includes the Premium performance MCUs and the Entry performance MCUs.

The TMS320F2837xD is a powerful 32-bit floating-point microcontroller unit (MCU) designed for advanced closed-loop control applications such as industrial motor drives; solar inverters and digital power; electrical vehicles and transportation; and sensing and signal processing. To accelerate application development, the DigitalPower software development kit (SDK) for C2000 MCUs and the MotorControl software development kit (SDK) for C2000™ MCUs are available. The F2837xD supports a new dual-core C28x architecture that significantly boosts system performance. The integrated analog and control peripherals also let designers consolidate control architectures and eliminate multiprocessor use in high-end systems.

The dual real-time control subsystems are based on TI’s 32-bit C28x floating-point CPUs, which provide 200MHz of signal processing performance in each core. The C28x CPUs are further boosted by the new TMU accelerator, which enables fast execution of algorithms with trigonometric operations common in transforms and torque loop calculations; and the VCU accelerator, which reduces the time for complex math operations common in encoded applications.

The F2837xD microcontroller family features two CLA real-time control coprocessors. The CLA is an independent 32-bit floating-point processor that runs at the same speed as the main CPU. The CLA responds to peripheral triggers and executes code concurrently with the main C28x CPU. This parallel processing capability can effectively double the computational performance of a real-time control system. By using the CLA to service time-critical functions, the main C28x CPU is free to perform other tasks, such as communications and diagnostics. The dual C28x+CLA architecture enables intelligent partitioning between various system tasks. For example, one C28x+CLA core can be used to track speed and position, while the other C28x+CLA core can be used to control torque and current loops.

The TMS320F2837xD supports up to 1MB (512KW) of onboard flash memory with error correction code (ECC) and up to 204KB (102KW) of SRAM. Two 128-bit secure zones are also available on each CPU for code protection.

Performance analog and control peripherals are also integrated on the F2837xD MCU to further enable system consolidation. Four independent 16-bit ADCs provide precise and efficient management of multiple analog signals, which ultimately boosts system throughput. The new sigma-delta filter module (SDFM) works in conjunction with the sigma-delta modulator to enable isolated current shunt measurements. The Comparator Subsystem (CMPSS) with windowed comparators allows for protection of power stages when current limit conditions are exceeded or not met. Other analog and control peripherals include DACs, PWMs, eCAPs, eQEPs, and other peripherals.

Peripherals such as EMIFs, CAN modules (ISO 11898-1/CAN 2.0B-compliant), and a new uPP interface extend the connectivity of the F2837xD. The uPP interface is a new feature of the C2000™ MCUs and supports high-speed parallel connection to FPGAs or other processors with similar uPP interfaces. Lastly, a USB 2.0 port with MAC and PHY lets users easily add universal serial bus (USB) connectivity to their application.

Want to learn more about features that make C2000 MCUs the right choice for your real-time control system? Check out The Essential Guide for Developing With C2000™ Real-Time Microcontrollers and visit the C2000™ real-time control MCUs page.

The Getting Started With C2000™ Real-Time Control Microcontrollers (MCUs) Getting Started Guide covers all aspects of development with C2000 devices from hardware to support resources. In addition to key reference documents, each section provides relevant links and resources to further expand on the information covered.

Ready to get started? Check out the TMDSCNCD28379D or LAUNCHXL-F28379D evaluation board sand download C2000Ware.

To learn more about the C2000 MCUs, visit the C2000 Overview at www.ti.com/c2000.

C2000™ 32-bit microcontrollers are optimized for processing, sensing, and actuation to improve closed-loop performance in real-time control applications such as industrial motor drives; solar inverters and digital power; electrical vehicles and transportation; motor control; and sensing and signal processing. The C2000 line includes the Premium performance MCUs and the Entry performance MCUs.

The TMS320F2837xD is a powerful 32-bit floating-point microcontroller unit (MCU) designed for advanced closed-loop control applications such as industrial motor drives; solar inverters and digital power; electrical vehicles and transportation; and sensing and signal processing. To accelerate application development, the DigitalPower software development kit (SDK) for C2000 MCUs and the MotorControl software development kit (SDK) for C2000™ MCUs are available. The F2837xD supports a new dual-core C28x architecture that significantly boosts system performance. The integrated analog and control peripherals also let designers consolidate control architectures and eliminate multiprocessor use in high-end systems.

The dual real-time control subsystems are based on TI’s 32-bit C28x floating-point CPUs, which provide 200MHz of signal processing performance in each core. The C28x CPUs are further boosted by the new TMU accelerator, which enables fast execution of algorithms with trigonometric operations common in transforms and torque loop calculations; and the VCU accelerator, which reduces the time for complex math operations common in encoded applications.

The F2837xD microcontroller family features two CLA real-time control coprocessors. The CLA is an independent 32-bit floating-point processor that runs at the same speed as the main CPU. The CLA responds to peripheral triggers and executes code concurrently with the main C28x CPU. This parallel processing capability can effectively double the computational performance of a real-time control system. By using the CLA to service time-critical functions, the main C28x CPU is free to perform other tasks, such as communications and diagnostics. The dual C28x+CLA architecture enables intelligent partitioning between various system tasks. For example, one C28x+CLA core can be used to track speed and position, while the other C28x+CLA core can be used to control torque and current loops.

The TMS320F2837xD supports up to 1MB (512KW) of onboard flash memory with error correction code (ECC) and up to 204KB (102KW) of SRAM. Two 128-bit secure zones are also available on each CPU for code protection.

Performance analog and control peripherals are also integrated on the F2837xD MCU to further enable system consolidation. Four independent 16-bit ADCs provide precise and efficient management of multiple analog signals, which ultimately boosts system throughput. The new sigma-delta filter module (SDFM) works in conjunction with the sigma-delta modulator to enable isolated current shunt measurements. The Comparator Subsystem (CMPSS) with windowed comparators allows for protection of power stages when current limit conditions are exceeded or not met. Other analog and control peripherals include DACs, PWMs, eCAPs, eQEPs, and other peripherals.

Peripherals such as EMIFs, CAN modules (ISO 11898-1/CAN 2.0B-compliant), and a new uPP interface extend the connectivity of the F2837xD. The uPP interface is a new feature of the C2000™ MCUs and supports high-speed parallel connection to FPGAs or other processors with similar uPP interfaces. Lastly, a USB 2.0 port with MAC and PHY lets users easily add universal serial bus (USB) connectivity to their application.

Want to learn more about features that make C2000 MCUs the right choice for your real-time control system? Check out The Essential Guide for Developing With C2000™ Real-Time Microcontrollers and visit the C2000™ real-time control MCUs page.

The Getting Started With C2000™ Real-Time Control Microcontrollers (MCUs) Getting Started Guide covers all aspects of development with C2000 devices from hardware to support resources. In addition to key reference documents, each section provides relevant links and resources to further expand on the information covered.

Ready to get started? Check out the TMDSCNCD28379D or LAUNCHXL-F28379D evaluation board sand download C2000Ware.

To learn more about the C2000 MCUs, visit the C2000 Overview at www.ti.com/c2000.
filter 尋找其它 即時數位電源 MCU
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 81
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 F28377D-SEP Dual-Core Real-Time Microcontroller datasheet (Rev. A) PDF | HTML 2026/1/27
* 使用指南 TMS320F2837xD Dual-Core Microcontrollers Technical Reference Manual (Rev. K) PDF | HTML 2024/5/28
* 使用指南 TMS320C28x Extended Instruction Sets Technical Reference Manual (Rev. C) 2019/10/29
* 勘誤表 TMS320F2837xD Dual-Core Real-Time MCUs Silicon Errata (Rev. N) PDF | HTML 2024/5/15
* 輻射及可靠性報告 Single-Event Effects (SEE) Radiation Report of the F28377D-SEP Dual-Core Real-Time Microcontroller PDF | HTML 2025/10/16
* 輻射及可靠性報告 F28377D-SEP Total Ionizing Dose (TID) Report 2025/10/13
白皮書 IC Sourcing for Space: Pros and Cons of Up-screening COTS Versus Space Enhanced Products (SEP) PDF | HTML 2026/7/28
應用說明 Highly Scalable Space Motor Control Platform based on TI’s Space Enhanced Products (-SEP) and Space Products PDF | HTML 2026/6/8
Product overview Implementing IEC 60730 / UL 1998 Compliance for C2000 Real-Time Microcontrollers (Rev. B) PDF | HTML 2026/6/4
應用說明 C2000™ MCU JTAG Connectivity Debug (Rev. D) PDF | HTML 2026/4/29
應用說明 Serial Flash Programming of C2000 Microcontrollers (Rev. I) PDF | HTML 2025/8/14
應用說明 EEPROM Emulation for Generation 3 C2000 Real-Time Controllers (Rev. B) PDF | HTML 2025/8/13
應用說明 MCU Control Center Tool Developer's Guide PDF | HTML 2025/8/4
應用說明 MCU Signal Sight Tool Developer's Guide PDF | HTML 2025/8/1
功能安全資訊 Certification for Functional Safety Hardware Process (Rev. C) 2025/6/6
應用說明 C2000-IDE Assist Tool Migration Feature Guide PDF | HTML 2025/4/23
使用指南 Getting Started with Bootloading on C2000™ Microcontrollers PDF | HTML 2025/4/8
應用說明 Digital Control Implementation for Hybrid Hysteretic Control LLC Converter (Rev. A) PDF | HTML 2024/8/21
Application brief Understanding Security Features for C2000 Real-Time Control MCUs (Rev. E) PDF | HTML 2024/8/5
應用說明 Development Tool Versions for C2000™ Support (Rev. A) PDF | HTML 2024/6/26
應用說明 Semiconductor and IC Package Thermal Metrics (Rev. D) PDF | HTML 2024/3/25
應用說明 VREFHI Input Driver Design for C2000 MCUs PDF | HTML 2024/1/18
應用說明 Clock Edge Delay Compensation With Isolated Modulators Digital Interface to MCUs (Rev. A) PDF | HTML 2024/1/12
使用指南 Migration Between TMS320F2837x and TMS320F28P65x PDF | HTML 2023/8/2
應用說明 CRC Engines in C2000 Devices (Rev. A) PDF | HTML 2023/5/1
應用說明 Migrating Software From 8-Bit (Byte) Addressable CPU’s to C28x CPU (Rev. A) PDF | HTML 2023/4/19
應用說明 Charge-Sharing Driving Circuits for C2000 ADCs (using PSPICE-FOR-TI) (Rev. A) PDF | HTML 2023/3/24
應用說明 Methods for Mitigating ADC Memory Cross-Talk (Rev. A) PDF | HTML 2023/3/24
應用說明 ADC Input Circuit Evaluation for C2000 Real-Time MCUs (using PSPICE-FOR-TI) PDF | HTML 2023/3/24
應用說明 C2000 ePWM Developer’s Guide (Rev. A) PDF | HTML 2023/2/24
應用說明 C2000 SysConfig Linker Command Tool PDF | HTML 2023/1/26
應用說明 Software Examples to Showcase Unique Capabilities of TI’s C2000™ CLA (Rev. A) PDF | HTML 2022/11/17
使用指南 C2000Ware motor control SDK getting started guide (Rev. A) PDF | HTML 2022/10/27
應用說明 C2000™ Hardware Built-In Self-Test (Rev. A) PDF | HTML 2022/9/28
應用說明 Intelligent LLC SR Control Using C2000 and UCD7138 (Rev. A) PDF | HTML 2022/6/27
應用說明 Interfacing EEPROM Using PMBus in I2C Mode PDF | HTML 2022/5/6
功能安全資訊 Functional Safety Manual for TMS320F2837xD, TMS320F2837xS and TMS320F2807x (Rev. D) PDF | HTML 2022/1/31
應用說明 Real-Time Benchmarks Showcasing C2000™ Control MCU's Optimized Signal Chain (Rev. A) PDF | HTML 2021/12/15
應用說明 Enhancing the Computational Performance of the C2000™ Microcontroller Family (Rev. C) PDF | HTML 2021/12/14
電子書 Real-Time Control Reference Guide PDF | HTML 2021/10/29
應用說明 C2000 SysConfig PDF | HTML 2021/10/20
應用說明 Programming Examples for the DCAN Module (Rev. A) PDF | HTML 2021/5/20
應用說明 Leverage New Type ePWM Features for Multiple Phase Control PDF | HTML 2021/5/11
應用說明 C2000™ DCSM Security Tool (Rev. A) PDF | HTML 2021/5/10
白皮書 結合 TI GaN FETs 與 C2000™ 即時 MCU，實現功率密集與有效率的數位電源系統 Download English Version 2021/3/18
更多文件說明 Maximize density, power, and reliability with TI GaN and C2000™ real-time MCUs 2020/12/15
應用說明 Quick Response Control of PMSM Using Fast Current Loop (Rev. B) 2020/12/7
應用說明 Flexible PWMs Enable Multi-Axis Drives, Multi-Level Inverters (Rev. B) PDF | HTML 2020/10/29
應用說明 Error Detection in SRAM (Rev. A) PDF | HTML 2020/10/28
應用說明 C2000™ Unique Device Number (Rev. B) PDF | HTML 2020/9/17
功能安全資訊 簡化汽車及工業領域的功 能安全認證 Download English Version 2020/6/9
使用指南 SYS/BIOS (TI-RTOS Kernel) User's Guide (Rev. V) 2020/6/1
使用指南 C2000Ware DigitalPower SDK Getting Started Guide (Rev. B) 2020/3/20
應用說明 Configurable Error Generator for Controller Area Network PDF | HTML 2019/12/19
白皮書 Simplify the integration of position sensors for industrial drive control system (Rev. A) 2019/11/21
應用說明 Dual-Axis Motor Control Using FCL and SFRA On a Single C2000™ MCU PDF | HTML 2019/8/7
使用指南 C2000™ Software Frequency Response Analyzer (SFRA) Library User’s Guide (Rev. A) PDF | HTML 2019/6/26
使用指南 Fast Current Loop Driverlib Library User’s Guide 2019/5/30
功能安全資訊 Report on certificate of the Safety MCU by TUV SUD 2019/5/7
技術文章 Motor control software development kit jump-starts new designs PDF | HTML 2019/4/17
應用說明 Updating Firmware on Security Enabled TMS320F2837xx or TMS320F2807x Devices 2018/12/4
功能安全資訊 Functional Safety: A tunable FMEDA for C2000™ MCUs 2018/7/27
應用說明 PowerPAD™ Thermally Enhanced Package (Rev. H) 2018/7/6
應用說明 Design and Usage Guidelines for the C2000 External Memory Interface (EMIF) (Rev. A) 2018/3/23
應用說明 Dual Motor Ctl Using FCL and Perf Analysis Using SFRA on TMS320F28379D LaunchPad (Rev. A) 2018/3/20
使用指南 Fast Current Loop (C28x) Library 2018/3/6
應用說明 Performance Analysis of Fast Current Loop (FCL) in Servo 2018/3/6
應用說明 Programming TMS320x28xx and 28xxx Peripherals in C/C++ (Rev. E) PDF | HTML 2017/12/19
應用說明 C2000 CPU Memory Built-In Self-Test 2017/11/27
應用說明 High Bandwidth Current Control of 3-Phase PMSM Using F2837x FCL Library 2017/5/8
應用說明 Fast Current Loop Library PDF | HTML 2017/5/8
應用說明 Built-In System Protection for Industrial Drives 2016/5/11
應用說明 High-Performance, High-Precision, Smart Sensing for Industrial Drives 2016/5/11
應用說明 Calculator for CAN Bit Timing Parameters PDF | HTML 2016/3/22
應用說明 The TMS320F2837xD Architecture: Achieving a New Level of High Performance 2016/2/11
使用指南 TMS320C28x DSP CPU and Instruction Set (Rev. F) 2015/4/10
應用說明 Accessing External SDRAM on the TMS320F2837x/2807x Microcontrollers Using C/C++ 2015/3/30
應用說明 Calculating FIT for a Mission Profile 2015/3/24
白皮書 Resolver-to-digital conversion implementation (Rev. A) 2014/3/26
應用說明 Running an Application from Internal Flash Memory on the TMS320F28xxx DSP (Rev. L) 2013/2/28
應用說明 TMS320C28x FPU Primer (Rev. A) 2009/7/20

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TIEVM-VIENNARECT — 使用 C2000™ MCU 且基於 Vienna 整流器的三相功率因數校正評估模組

Vienna 整流器電源拓撲用於高功率三相功率因數 (AC-DC) 應用，如板外電動車 (EV) 充電器和電信整流器。此設計說明了使用 C2000™ MCU 控制功率級的方法。此設計使用 HSEC180 controlCARD 介面，且軟體支援 MCU 的 F2837x 或 F2838x 和 F28004x 系列。

進一步了解 C2000 MCU 可為電動車應用提供哪些功能。
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

XDS110ISO-EVM — 適用於 C2000 和 Sitara™ controlSOM 的 XDS110 隔離插入式評估模組

XDS110 隔離插入式電路板是一款適用於 C2000 和 Sitara controlSOM 的即時偵錯及 Flash 編程評估模組。可透過非隔離式 120 針腳連接器或電氣隔離式 16 針腳連接器連接 C2000 及 Sitara controlSOM。兩種接頭皆具備 JTAG/cJTAG/SWD 支援和全雙工 UART 埠。電路板支援兩個額外功能，可在目標電路板偵錯中使用：序列周邊介面 (SPI) 至四個隔離式數位類比轉換器 (DAC) 通道，以及最多六個數位和四個類比非隔離通道。
使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

ALGO-3P-UISP1-TI — 適用於德州儀器裝置的 Algocraft μISP1 編程器

μISP 可以連接到主機 PC (內建 RS-232、USB、LAN 連接) 或獨立模式工作。

在單機模式下，只要按下「開始」按鈕或透過一些 TTL 控制線，就可以執行編程週期。

其緊湊的尺寸和多功能性可輕鬆整合到生產環境、手動和自動化程序中。

從：Algocraft
支援產品和硬體
開發套件

LAUNCHXL-F28379D — 適用 C2000™ Delfino™ MCU 的 F28379D LaunchPad™ 開發套件

LAUNCHXL-F28379D 是適合 TI MCU LaunchPad™ 開發套件生態系統中 TMS320F2837xD、TMS320F2837xS 及 TMS320F2807x 產品的低成本評估與開發工具，與各種插件 BoosterPack（如使用下方「功能」章節中的「建議 BoosterPack™ 外掛程式模組」中建議）相容。此 LaunchPad 開發套件擴充版本支援兩個 BoosterPack 連線。LaunchPad 開發套件提供標準化且容易使用的平台，可在開發您下一個應用程式時派上用場。

 

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發套件

TIEVM-HV-1PH-DCAC — 具有電壓源和併聯模式的單相逆變器開發套件

此參考設計實現了單相逆變器 (DC-AC) 控制，採用 C2000™ F2837xD 與 F28004x 微控制器。設計支援逆變器的兩種操作模式。首先是使用輸出 LC 濾波器的電壓源模式，此控制模式通常用於不斷電裝置。   第二個則是搭載輸出 LCL 濾波器的併聯模式，通常用於太陽能逆變器。powerSUITE 架構支援適用於設計的韌體，可利用 Solution Adapter 進行修改，並利用 Compensation Designer 和 SFRA 調整控制迴路。高效率、低 THD 和直覺式軟體，讓此設計對於從事 UPS 逆變器設計以及 PV (...)
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發套件

TMDSDOCK28379D — F28379D Delfino 實驗套件

TMDSDOCK28379D 是一款 HSEC180 controlCARD 架構的評估和開發工具，適用於 C2000™ Delfino™ F2837x 和 Piccolo F2807x 系列的微控制器產品。擴充站爲 controlCARD 提供電源，並提供原型設計的麪包板區域。使用一系列的排針存取主要裝置訊號。

使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發套件

TMDXIDDK379D — 適用於工業馬達控制的 C2000 DesignDRIVE 開發套件

DesignDRIVE 開發套件 (IDDK) 硬體提供含完整功率級的整合式伺服驅動設計，可驅動高電壓三相馬達，並能簡化對各種位置回饋、電流感測與控制拓撲的評估。

C2000™ MCU 上的感測週邊設備包括八個 ΔΣ sinc 濾波器，四個 16 或 12 位元 ADC 和窗型比較器，可讓 DesignDRIVE 套件同時支援分流、磁通量閘門/霍爾和 ΔΣ 電流感測。在位置回饋方面，本套件運用整合在 C2000 MCU 上的位置管理解決方案，支援 EnDat、BiSS、T-format、增量編碼器以及 SINCOS 與解析器類比感測器。此外，客戶也可探索配置選項，以允許將 MCU (...)
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
子卡

BOOSTXL-3PHGANINV — 具有基於分流的直列式馬達相電流感測的 48V 三相逆變器評估模組

BOOSTXL-3PHGANINV 評估模組採用具精密直列分流式相位電流感測的 48V/10A 三相 GaN 逆變器，以準確控制伺服驅動器等精密驅動器。
 

MathWorks MATLAB & Simulink 範例型號包括以下內容：

使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
子卡

BOOSTXL-POSMGR — C2000 DesignDRIVE 位置管理器 BoosterPack™ 插入模組

PositionManager BoosterPack 是彈性低電壓平台，用於評估絕對式編碼器和類比感測器（如解析器和 SinCos 轉換器）的介面。  當結合 DesignDRIVE Position Manager 軟體解決方案時，這個低成本的評估模組就會成為強大工具，可用於連接許多常用的位置編碼器類型，例如 EnDat、BiSS 和 T-format，以及 C2000 即時控制裝置。  C2000 Position Manager 技術將最常用的數位和類比位置感測器介面整合到 C2000 即時控制器上，因此無需使用外部 FPGA 來執行這些功能。
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
子卡

TMDSCNCD28379D — 適用 C2000™ Delfino MCU controlCARD™ 的 F28379D 開發套件

TMDSCNCD28379D 是適用 TI MCU 中 F2837xD、F2837xS 和 F2807x 系列的 HSEC180 controlCARD 式評估與開發工具。controlCARD 是利用兩個標準外型規格之一（100 針腳 DIMM 或 180 針腳 HSEC）的完整電路板級模組，可提供小巧型單電路板控制器解決方案。首次評估時，controlCARD 通常會搭配基板或含在應用套件中購買。

使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
子卡

TMDSHSECDOCK — HSEC180 controlCARD 基板擴充站

TMDSHSECDOCK 為一塊基板，可為相容的 HSEC180 架構 controlCARD 提供關鍵訊號的接頭針腳存取。提供模擬板區域以快速進行原型設計。電路板電源可由 USB 纜線或 5-V 桶式電源供應器供電。

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
偵錯探測器

TMDSEMU110-U — XDS110 JTAG 偵錯探測器

德州儀器 XDS110 是一種全新的偵錯探測器 (模擬器) 類別，適用於 TI 嵌入式處理器。XDS110 取代 XDS100 系列，可在單一 Pod 中支援更廣泛的標準 (IEEE1149.1、IEEE1149.7、SWD)。同時，所有 XDS 偵錯探針在所有配備嵌入式追蹤緩衝器 (ETB) 的 Arm® 與 DSP 處理器中均支援核心與系統追蹤。  對於針腳上的核心追蹤，則需要 XDS560v2 PRO TRACE。

德州儀器 XDS110 透過 TI 20 針腳連接器（具有用於 TI 14 針腳和 Arm 10 針腳和 Arm 20 針腳的多轉接器）連接到目標電路板，並透過 USB2.0 (...)

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
偵錯探測器

TMDSEMU200-U — XDS200 USB 偵錯探測器

XDS200 是為 TI 嵌入式裝置偵錯的偵錯探測器（模擬器）。對於大多數裝置，建議使用較新、成本較低的 XDS110 (www.ti.com/tool/TMDSEMU110-U)。XDS200 支援單一 Pod 中廣泛的標準（IEEE1149.1、IEEE1149.7、SWD）。所有 XDS 偵錯探針在所有配備嵌入式追蹤緩衝器 (ETB) 的 Arm® 與 DSP 處理器中均支援核心與系統追蹤。

XDS200 透過 TI 20 接腳連接器（配備適用 TI 14 接腳、Arm Cortex® 10 接腳和 Arm 20 接腳的多重轉接器）連接到目標電路板，並透過 USB2.0 高速 (...)

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
偵錯探測器

TMDSEMU560V2STM-U — XDS560™ 軟體 v2 系統追蹤 USB 偵錯探測器

XDS560v2 是 XDS560™ 系列偵錯探測器中性能最高的，且同時支援傳統 JTAG 標準 (IEEE1149.1) 與 cJTAG (IEEE1149.7)。  請注意，其不支援序列線偵錯 (SWD)。

所有 XDS 偵錯探測器均在所有配備嵌入式追蹤緩衝器 (ETB) 的 ARM 與 DSP 處理器中支援核心與系統追蹤。  對於針腳上的追蹤，則需要 XDS560v2 PRO TRACE。

XDS560v2 透過 MIPI HSPT 60 針腳接頭 (具有用於 TI 14 針腳、TI 20 針腳和 ARM 20 針腳的多轉接器) 連接到目標電路板，並透過 USB2.0 高速 (...)

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
偵錯探測器

TMDSEMU560V2STM-UE — XDS560v2 System Trace USB 與乙太網路偵錯探測器

The XDS560v2 is the highest performance of the XDS560™ family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7). Note that it does not support serial wire debug (SWD).

All XDS debug probes support Core and System Trace in all ARM and DSP processors (...)

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
硬體程式設計工具

ALGO-3P-WRITENOW — Algocraft WriteNow！程式設計工具

WriteNow! 系統內編程器系列是可編程產業的一大突破。此編程器支援多家製造商的眾多裝置 (例如微控制器、記憶體、CPLD 與其他可編程裝置)。其尺寸精巧，便於整合至 ATE 與固定裝置。編程器可單機運作，或透過內建的 RS-232、LAN 與 USB 連接埠與主機電腦連線，並隨附操作簡易的工具軟體。

從：Algocraft
支援產品和硬體
IDE、配置、編譯器或偵錯程式

EDGE-AI-STUDIO-MCU — Edge AI Studio for Microcontrollers

Edge AI Studio 是一系列圖形和命令行工具，旨在加速 TI 處理器、微控制器和雷達感測器上的邊緣 AI 開發。不管是使用來自 TI Model Zoo 的模型，還是
運用您自己的模型來開發概念驗證，Edge AI Studio 都能提供您所需的工具。

Edge AI Studio 圖形使用者介面提供完全整合的解決方案，用於收集和註釋資料、訓練和編譯模型，以在即時開發平台上部署。從 TI Model Zoo 中的各種預先訓練的模型中選擇，並可選擇透過自訂資料重新訓練，以提升準確度和性能。Edge AI Studio (...)

支援產品和硬體
IDE、配置、編譯器或偵錯程式

SYSCONFIG — Standalone desktop version of SysConfig

CCStudio™ SysConfig is part of TI's extensive CCStudio™ development ecosystem and is a configuration tool that simplifies hardware and software configuration challenges to accelerate software development.

SysConfig provides an intuitive graphical user interface for configuring pins, peripherals, (...)

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HLQFP (PTP) 176 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片