首頁 放大器 運算放大器 (op amps) 一般用途運算放大器
首頁
放大器
運算放大器 (op amps)
一般用途運算放大器

LM358-N

現行

雙路、32-V、1-MHz 運算放大器

立即訂購
產品規格表

現在提供此產品的更新版本

open-in-new 比較替代產品
具備升級功能，可直接投入使用替代所比較的裝置。
LM358B 現行 操作溫度範圍為 -40°C 至 85°C 的雙路、36V、1.2MHz、3mV 偏移電壓運算放大器 Pin-to-pin upgrade with improved performance and lower 1ku price.

LM358-N

現行
產品規格表 立即訂購

產品詳細資料

Number of channels 2 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 32 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 3 Rail-to-rail In to V- GBW (typ) (MHz) 1 Slew rate (typ) (V/µs) 0.1 Vos (offset voltage at 25°C) (max) (mV) 7 Iq per channel (typ) (mA) 0.25 Vn at 1 kHz (typ) (nV√Hz) 40 Rating Catalog Operating temperature range (°C) 0 to 70 Offset drift (typ) (µV/°C) 7 Input bias current (max) (pA) 150000 CMRR (typ) (dB) 85 Iout (typ) (A) 0.02 Architecture Bipolar Input common mode headroom (to negative supply) (typ) (V) 0 Input common mode headroom (to positive supply) (typ) (V) -1.5 Output swing headroom (to negative supply) (typ) (V) 0.005 Output swing headroom (to positive supply) (typ) (V) -2
Number of channels 2 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 32 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 3 Rail-to-rail In to V- GBW (typ) (MHz) 1 Slew rate (typ) (V/µs) 0.1 Vos (offset voltage at 25°C) (max) (mV) 7 Iq per channel (typ) (mA) 0.25 Vn at 1 kHz (typ) (nV√Hz) 40 Rating Catalog Operating temperature range (°C) 0 to 70 Offset drift (typ) (µV/°C) 7 Input bias current (max) (pA) 150000 CMRR (typ) (dB) 85 Iout (typ) (A) 0.02 Architecture Bipolar Input common mode headroom (to negative supply) (typ) (V) 0 Input common mode headroom (to positive supply) (typ) (V) -1.5 Output swing headroom (to negative supply) (typ) (V) 0.005 Output swing headroom (to positive supply) (typ) (V) -2
PDIP (P) 8 92.5083 mm² (9.81 mm × 9.43 mm) SOIC (D) 8 29.4 mm² (4.9 mm × 6 mm) DSBGA (YPB) 8 3.0625 mm² (— mm × — mm) TO-CAN (LMC) 8 80.2816 mm² (8.96 mm × 8.96 mm)
  • Available in 8-bump DSBGA chip-sized package (see AN-1112, SNVA009)
  • Internally frequency compensated for unity gain
  • Large DC voltage gain: 100 dB
  • Wide bandwidth (unity gain): 1 MHz (temperature compensated)
  • Wide power supply range:
    • Single supply: 3 V to 32 V
    • Or dual supplies: ±1.5 V to ±16 V
  • Very low supply current drain (500 µA) essentially independent of supply voltage
  • Low input offset voltage: 2 mV
  • Input common-mode voltage range includes ground
  • Differential input voltage range equal to the power supply voltage
  • Large output voltage swing
  • Unique characteristics:
    • In the Linear Mode the input common-mode voltage range includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage
    • The unity gain cross frequency is temperature compensated
    • The input bias current is also temperature compensated
  • Advantages:
    • Two internally compensated op amps
    • Eliminates need for dual supplies
    • Allows direct sensing near GND and VOUT also goes to GND
    • Compatible with all forms of logic
    • Power drain suitable for battery operation
  • Available in 8-bump DSBGA chip-sized package (see AN-1112, SNVA009)
  • Internally frequency compensated for unity gain
  • Large DC voltage gain: 100 dB
  • Wide bandwidth (unity gain): 1 MHz (temperature compensated)
  • Wide power supply range:
    • Single supply: 3 V to 32 V
    • Or dual supplies: ±1.5 V to ±16 V
  • Very low supply current drain (500 µA) essentially independent of supply voltage
  • Low input offset voltage: 2 mV
  • Input common-mode voltage range includes ground
  • Differential input voltage range equal to the power supply voltage
  • Large output voltage swing
  • Unique characteristics:
    • In the Linear Mode the input common-mode voltage range includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage
    • The unity gain cross frequency is temperature compensated
    • The input bias current is also temperature compensated
  • Advantages:
    • Two internally compensated op amps
    • Eliminates need for dual supplies
    • Allows direct sensing near GND and VOUT also goes to GND
    • Compatible with all forms of logic
    • Power drain suitable for battery operation

The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage.

Application areas include transducer amplifiers, DC gain blocks and all the conventional op-amp circuits which now can be more easily implemented in single power supply systems. For example, the LM158 series can be directly operated off of the standard 3.3-V power supply voltage which is used in digital systems and will easily provide the required interface electronics without requiring the additional ±15-V power supplies.

The LM358 and LM2904 are available in a chip-sized package (8-bump DSBGA) using TI’s DSBGA package technology.

The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage.

Application areas include transducer amplifiers, DC gain blocks and all the conventional op-amp circuits which now can be more easily implemented in single power supply systems. For example, the LM158 series can be directly operated off of the standard 3.3-V power supply voltage which is used in digital systems and will easily provide the required interface electronics without requiring the additional ±15-V power supplies.

The LM358 and LM2904 are available in a chip-sized package (8-bump DSBGA) using TI’s DSBGA package technology.
filter 尋找其它 一般用途運算放大器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
LM358LV 現行 雙路、5.5-V、1-MHz 運算放大器 Optimized for low-voltage (5.5V) operation

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 10
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 LMx58-N Low-Power, Dual-Operational Amplifiers datasheet (Rev. J) PDF | HTML 2022/3/14
應用說明 Application Design Guidelines for LM324 and LM358 Devices (Rev. B) PDF | HTML 2023/7/19
電子書 The Signal e-book: A compendium of blog posts on op amp design topics PDF | HTML 2017/3/28
應用說明 AN-298 Isolation Techniques for Signal Conditioning (Rev. B) 2013/5/6
應用說明 AN-116 Use the LM158/LM258/LM358 Dual, Single Supply Op Amp (Rev. B) 2013/4/23
應用說明 Applications of the LM3524 Pulse Width Modulator (Rev. B) 2013/4/23
應用說明 AN-C V/F Converter ICs Handle Frequency-to-Voltage Needs (Rev. B) 2013/4/23
應用說明 Using ADC0808/809 8-Bit uP Compble ADCs w/8-Chan Analog Multiplexr (Rev. B) 2013/4/22
應用說明 Effect of Heavy Loads on Accuracy and Linearity of Op Amp Circuits (Rev. B) 2013/4/22
應用說明 AN-284 Single-Supply Applications of CMOS MICRODACs (Rev. B) 2013/4/22

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

AMP-PDK-EVM — 放大器性能開發套件評估模組

放大器性能開發套件 (PDK) 是一款評估模組 (EVM) 套件，可測試通用運算放大器 (op amp) 參數，並與大多數運算放大器和比較器相容。EVM 套件提供主板和多個插槽式子卡選項，可滿足封裝需求，使工程師能夠快速評估和驗證裝置性能。

AMP-PDK-EVM 套件支援五種最熱門的業界標準封裝，包括：

  • D (SOIC-8 和 SOIC-14)
  • PW (TSSOP-14)
  • DGK (VSSOP-8)
  • DBV (SOT23-5 和 SOT23-6)
  • DCK (SC70-5 和 SC70-6)
使用指南: PDF | HTML
支援產品和硬體
開發板

DIP-ADAPTER-EVM — DIP 轉接器評估模組

Speed up your op amp prototyping and testing with the DIP-Adapter-EVM, which provides a fast, easy and inexpensive way to interface with small, surface-mount ICs. You can connect any supported op amp using the included Samtec terminal strips or wire them directly to existing circuits.

The (...)

支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

DUAL-DIYAMP-EVM — 用於 SOIC 封裝的雙通道通用自製 (DIY) 放大器電路評估模組

DUAL-DIYAMP-EVM 是一系列評估模組 (EVM)，提供工程師與自組愛好者 (DIYer) 實作型放大器電路，協助快速評估設計概念並驗證模擬結果。其是專為採用業界標準 SOIC-8 封裝的雙封裝運算放大器而設計。其可實現反向及非反向放大器、Sallen key 濾波器、多回饋濾波器、含參考緩衝器的差動放大器、含雙回饋的 Riso、單端輸入至差動輸出、差動輸入至差動輸出、雙運算放大器儀器放大器和並聯運算放大器。

DUAL-DIYAMP-EVM 可快速製作電路原型，並採用常見的 0805 或 0603 表面裝載元件。透過多種組合方式，此 EVM (...)

使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
模擬型號

LMx58_LM2904 PSpice Model (Rev. C)

SNOM268C.ZIP (23 KB) - PSpice 模型
支援產品和硬體
模擬型號

LMx58_LM2904 Reference Design

SNOM671.ZIP (22 KB) - TINA-TI 參考設計
支援產品和硬體
模擬型號

LMx58_LM2904 TINA-TI Macro

SNOM670.ZIP (4 KB) - TINA-TI Spice 模型
支援產品和硬體
參考設計

PMP20612 — 高效率和低總諧波失真 200W AC-DC LED 驅動器參考設計

PMP20612 參考設計是一款具有超低總諧波失真 (THD) 的高效率 AC-DC LED 驅動器參考設計。此設計使用 CCM PFC 與 UCC28180 控制器，以提供 108VAC 至 305VAC 輸入的功率因數校正 (PFC) 功能。配備 UCC28740 控制器的雙開關返馳式轉換器可用於提供 200V/1A 定電流 (CC) / 定電壓 (CV)。輸出側的 TL431 和 INA180 電壓感測與電流感測電路，可讓外部電路處理調光功能。因此，此設計在 230VAC/50Hz 輸入時可達 92.9% 峰值效率。在 277VAC 下，此電路板在 20% 負載下也具有低於 20% (...)
支援產品和硬體
參考設計

TIDA-01464 — 具有可調整輸出的 200W 92% 高效低 THD 10% 可調光 AC/DC LED 驅動器參考設計

本參考設計為一款 200W 可調光、低 THD AC/DC LED 電源供應器，具備 100 至 200V 可調輸出電壓，專為戶外照明應用設計，例如：路燈照明、道路照明等。此設計採用 CCM PFC 作為前端電路，以實現低 THD 與高功率因數，並建議使用雙開關返馳式架構作為第二級，有助於滿足可調輸出電壓 LED 電源供應器在成本、效率與設計簡潔性等方面的需求。
支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
PDIP (P) 8 Ultra Librarian
SOIC (D) 8 Ultra Librarian
DSBGA (YPB) 8 Ultra Librarian
TO-CAN (LMC) 8 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片