SLLSFR8B September   2025  – January 2026 TCAN5102-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Supply Characteristics
    6. 5.6 Electrical Characteristics
    7. 5.7 Timing Requirements
    8. 5.8 Switching Characteristics
    9. 5.9 I2C Bus Timing Requirements
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  VDD
      2. 7.3.2  PROG Pin
      3. 7.3.3  DIGFLTR Pin
      4. 7.3.4  GPIOx and Pin Muxing Special Functions
        1. 7.3.4.1 GPIO Synchronization
      5. 7.3.5  EEPROM
      6. 7.3.6  SPI Controller
      7. 7.3.7  UART Controller
      8. 7.3.8  I2C Controller
        1. 7.3.8.1 I2C Stuck Bus Recovery
      9. 7.3.9  PWM Controller
      10. 7.3.10 CAN Transceiver Control Pins
      11. 7.3.11 Under-Voltage Lockout and Unpowered Device
    4. 7.4 Device Functional Modes
      1. 7.4.1 Init Mode
      2. 7.4.2 Sleep Mode
      3. 7.4.3 Normal Mode
    5. 7.5 Programming
      1. 7.5.1 Device Programming via SPI Peripheral Mode
      2. 7.5.2 CAN FD Light Protocol
        1. 7.5.2.1 CAN Frame Format
      3. 7.5.3 Message RAM (MRAM) and IP Enable
      4. 7.5.4 SPI Controller
        1. 7.5.4.1 SPI Pins
          1. 7.5.4.1.1 SPI Clock (SCLK)
          2. 7.5.4.1.2 Peripheral In Controller Out (PICO)
          3. 7.5.4.1.3 Peripheral Out Controller In (POCI)
          4. 7.5.4.1.4 Chip Select (CS or nCS)
        2. 7.5.4.2 SPI Clock Generator
        3. 7.5.4.3 SPI Control Protocol
          1. 7.5.4.3.1 SPI Write Example 1
          2. 7.5.4.3.2 SPI Read Example 1
      5. 7.5.5 UART Controller
        1. 7.5.5.1 UART Baud Rate Generation and Fractional Divisor
        2. 7.5.5.2 UART Control Protocol
          1. 7.5.5.2.1 UART Write Example 1
          2. 7.5.5.2.2 UART Read Example 1
      6. 7.5.6 I2C Controller
        1. 7.5.6.1 I2C Baud Rate Generation
        2. 7.5.6.2 I2C Stuck Bus Recovery
        3. 7.5.6.3 I2C Control Protocol
          1. 7.5.6.3.1 I2C Write Example 1
          2. 7.5.6.3.2 I2C Read Example 1
      7. 7.5.7 PWM and Trapezoidal PWM Ramp Profiles
        1. 7.5.7.1 Trapezoidal Ramp Control
          1. 7.5.7.1.1 Duty Cycle Ramping
          2. 7.5.7.1.2 Switching Frequency Ramping
          3. 7.5.7.1.3 Off-Ramp
        2. 7.5.7.2 PWM Clock Generator
        3. 7.5.7.3 PWM Duty Cycle
        4. 7.5.7.4 Ramp Slope and Scale Factor
          1. 7.5.7.4.1 Duty Cycle Ramp Slope
          2. 7.5.7.4.2 Switching Frequency Ramp Slope
        5. 7.5.7.5 Automatic Deceleration and Stop Conditions
          1. 7.5.7.5.1 Automatic Deceleration Off-Ramp with Pulse Counting
          2. 7.5.7.5.2 Automatic Deceleration/Off-Ramp with GPIO Input
        6. 7.5.7.6 Duty Cycle Ramp Example
        7. 7.5.7.7 Frequency Ramp Example
        8. 7.5.7.8 Static On Example
    6. 7.6 Register Maps
      1. 7.6.1 DEVICE Registers
        1. 7.6.1.1  DEV_ID[y] Register (Offset = 0h + formula) [Reset = 0032303135414354h]
        2. 7.6.1.2  DEV_ID_REV Register (Offset = 8h) [Reset = 10h]
        3. 7.6.1.3  DEV_CMD Register (Offset = 9h) [Reset = 00h]
        4. 7.6.1.4  DEV_CFG_EN Register (Offset = Ah) [Reset = 00h]
        5. 7.6.1.5  DEV_CFG_BR Register (Offset = Bh) [Reset = 10h]
        6. 7.6.1.6  DEV_CFG_ID_0 Register (Offset = Ch) [Reset = 00h]
        7. 7.6.1.7  DEV_CFG_ID_1 Register (Offset = Dh) [Reset = 00h]
        8. 7.6.1.8  DEV_CFG_ID_BCST_0 Register (Offset = Eh) [Reset = 00h]
        9. 7.6.1.9  DEV_CFG_ID_BCST_1 Register (Offset = Fh) [Reset = 00h]
        10. 7.6.1.10 DEV_CFG_ID_BCST_MASK_0 Register (Offset = 10h) [Reset = 00h]
        11. 7.6.1.11 DEV_CFG_ID_BCST_MASK_1 Register (Offset = 11h) [Reset = 00h]
        12. 7.6.1.12 DEV_CFG_NVM_PROG_CODE Register (Offset = 12h) [Reset = 00h]
        13. 7.6.1.13 DEV_CFG_NVM_PROG Register (Offset = 13h) [Reset = 00h]
        14. 7.6.1.14 INT_CFG Register (Offset = 1Dh) [Reset = 00h]
        15. 7.6.1.15 DEV_IE_0 Register (Offset = 1Eh) [Reset = 00h]
        16. 7.6.1.16 DEV_IE_1 Register (Offset = 1Fh) [Reset = 00h]
        17. 7.6.1.17 MRAM_IP_CFG Register (Offset = 20h) [Reset = 00h]
        18. 7.6.1.18 IO_CFG_0 Register (Offset = 21h) [Reset = 00h]
        19. 7.6.1.19 IO_CFG_1 Register (Offset = 22h) [Reset = 00h]
        20. 7.6.1.20 IO_OE_0 Register (Offset = 23h) [Reset = 00h]
        21. 7.6.1.21 IO_OE_1 Register (Offset = 24h) [Reset = 00h]
        22. 7.6.1.22 IO_OD_0 Register (Offset = 25h) [Reset = 00h]
        23. 7.6.1.23 IO_OD_1 Register (Offset = 26h) [Reset = 00h]
        24. 7.6.1.24 IO_RE_0 Register (Offset = 27h) [Reset = 00h]
        25. 7.6.1.25 IO_RE_1 Register (Offset = 28h) [Reset = 00h]
        26. 7.6.1.26 IO_PU_0 Register (Offset = 29h) [Reset = 00h]
        27. 7.6.1.27 IO_PU_1 Register (Offset = 2Ah) [Reset = 00h]
        28. 7.6.1.28 IO_POL_0 Register (Offset = 2Bh) [Reset = 00h]
        29. 7.6.1.29 IO_POL_1 Register (Offset = 2Ch) [Reset = 00h]
        30. 7.6.1.30 IO_OUTPUT_0 Register (Offset = 2Dh) [Reset = 00h]
        31. 7.6.1.31 IO_OUTPUT_1 Register (Offset = 2Eh) [Reset = 00h]
        32. 7.6.1.32 IO_INPUT_0 Register (Offset = 2Fh) [Reset = 00h]
        33. 7.6.1.33 IO_INPUT_1 Register (Offset = 30h) [Reset = 00h]
        34. 7.6.1.34 IR_STATUS Register (Offset = 31h) [Reset = 00h]
        35. 7.6.1.35 DEV_IR Register (Offset = 32h) [Reset = 00h]
        36. 7.6.1.36 SPI_IR Register (Offset = 33h) [Reset = 00h]
        37. 7.6.1.37 UART_IR Register (Offset = 34h) [Reset = 00h]
        38. 7.6.1.38 I2C_IR Register (Offset = 35h) [Reset = 00h]
        39. 7.6.1.39 PWM0_IR Register (Offset = 36h) [Reset = 00h]
        40. 7.6.1.40 PWM1_IR Register (Offset = 37h) [Reset = 00h]
      2. 7.6.2 SPI Registers
        1. 7.6.2.1  SPI_CREL Register (Offset = 1000h) [Reset = 87h]
        2. 7.6.2.2  SPI_SCRATCH Register (Offset = 1001h) [Reset = 00h]
        3. 7.6.2.3  SPI_CTRL Register (Offset = 1002h) [Reset = 00h]
        4. 7.6.2.4  SPI_CFG_0 Register (Offset = 1003h) [Reset = 00h]
        5. 7.6.2.5  SPI_CFG_1 Register (Offset = 1004h) [Reset = 00h]
        6. 7.6.2.6  SPI_DR_0 Register (Offset = 1005h) [Reset = 00h]
        7. 7.6.2.7  SPI_DR_1 Register (Offset = 1006h) [Reset = 00h]
        8. 7.6.2.8  SPI_DR_2 Register (Offset = 1007h) [Reset = 00h]
        9. 7.6.2.9  SPI_DR_3 Register (Offset = 1008h) [Reset = 00h]
        10. 7.6.2.10 SPI_CHAN_EN Register (Offset = 1009h) [Reset = 00h]
        11. 7.6.2.11 SPI_CS_POL Register (Offset = 100Ah) [Reset = 00h]
        12. 7.6.2.12 SPI_FIFO_CTRL Register (Offset = 100Bh) [Reset = 0h]
        13. 7.6.2.13 SPI_IE_0 Register (Offset = 100Ch) [Reset = 00h]
        14. 7.6.2.14 SPI_IE_1 Register (Offset = 100Dh) [Reset = 00h]
        15. 7.6.2.15 SPI_IR Register (Offset = 100Eh) [Reset = 00h]
        16. 7.6.2.16 SPI_FS Register (Offset = 100Fh) [Reset = 80h]
        17. 7.6.2.17 SPI_TX_FIFO Register (Offset = 1010h) [Reset = 0000h]
        18. 7.6.2.18 SPI_RX_FIFO Register (Offset = 1010h) [Reset = 0000h]
        19. 7.6.2.19 SPI_RXFS Register (Offset = 1011h) [Reset = 00h]
        20. 7.6.2.20 SPI_TXFS Register (Offset = 1012h) [Reset = 00h]
        21. 7.6.2.21 SPI_TXES Register (Offset = 1013h) [Reset = 00h]
      3. 7.6.3 SPI Data FIFOs
        1. 7.6.3.1 SPI Transmit FIFO (address = h1010)
        2. 7.6.3.2 SPI Receive FIFO (address = h1010)
      4. 7.6.4 UART Registers
        1. 7.6.4.1  UART_CREL Register (Offset = 2000h) [Reset = 10h]
        2. 7.6.4.2  UART_SCRATCH Register (Offset = 2001h) [Reset = 00h]
        3. 7.6.4.3  UART_CTRL Register (Offset = 2002h) [Reset = 04h]
        4. 7.6.4.4  UART_BR_LSB Register (Offset = 2003h) [Reset = 00h]
        5. 7.6.4.5  UART_BR_MSB Register (Offset = 2004h) [Reset = 00h]
        6. 7.6.4.6  UART_BR_FRAC Register (Offset = 2005h) [Reset = 00h]
        7. 7.6.4.7  UART_FIFO_CTRL Register (Offset = 2006h) [Reset = 01h]
        8. 7.6.4.8  UART_IE_0 Register (Offset = 2007h) [Reset = 00h]
        9. 7.6.4.9  UART_IE_1 Register (Offset = 2008h) [Reset = 00h]
        10. 7.6.4.10 UART_IR Register (Offset = 2009h) [Reset = 00h]
        11. 7.6.4.11 UART_STATUS Register (Offset = 200Ah) [Reset = 60h]
        12. 7.6.4.12 UART_RXFS Register (Offset = 200Bh) [Reset = 00h]
        13. 7.6.4.13 UART_TXFS Register (Offset = 200Ch) [Reset = 00h]
        14. 7.6.4.14 UART_RX_FIFO Register (Offset = 2010h) [Reset = 00h]
        15. 7.6.4.15 UART_TX_FIFO Register (Offset = 2010h) [Reset = 00h]
        16. 7.6.4.16 UART_RX_ERR_STATUS Register (Offset = 2011h) [Reset = 00h]
      5. 7.6.5 UART Data FIFOs
        1. 7.6.5.1 UART Transmit FIFO (address = h2010)
        2. 7.6.5.2 UART Receive FIFO (address = h2010)
        3. 7.6.5.3 UART Receive Error Status (address = h2011)
      6. 7.6.6 I2C Registers
        1. 7.6.6.1  I2C_CREL Register (Offset = 3000h) [Reset = 10h]
        2. 7.6.6.2  I2C_SCRATCH Register (Offset = 3001h) [Reset = 00h]
        3. 7.6.6.3  I2C_CTRL Register (Offset = 3002h) [Reset = 18h]
        4. 7.6.6.4  I2C_BR Register (Offset = 3003h) [Reset = 18h]
        5. 7.6.6.5  I2C_FIFO_CTRL Register (Offset = 3004h) [Reset = 00h]
        6. 7.6.6.6  I2C_IE_0 Register (Offset = 3005h) [Reset = 00h]
        7. 7.6.6.7  I2C_IE_1 Register (Offset = 3006h) [Reset = 00h]
        8. 7.6.6.8  I2C_IR Register (Offset = 3007h) [Reset = 00h]
        9. 7.6.6.9  I2C_STATUS Register (Offset = 3008h) [Reset = XXh]
        10. 7.6.6.10 I2C_FS Register (Offset = 3009h) [Reset = 00h]
        11. 7.6.6.11 I2C_RXFS Register (Offset = 300Ah) [Reset = 00h]
        12. 7.6.6.12 I2C_TXFS Register (Offset = 300Bh) [Reset = 00h]
        13. 7.6.6.13 I2C_TXES Register (Offset = 300Ch) [Reset = 00h]
      7. 7.6.7 I2C Data FIFOs
        1. 7.6.7.1 I2C Transmit FIFO (address = h3010)
        2. 7.6.7.2 I2C Receive FIFO (address = h3010)
      8. 7.6.8 PWM0 Registers
        1. 7.6.8.1  PWM1_ACTION Register (Offset = 4000h) [Reset = 00h]
        2. 7.6.8.2  PWM0_CTRL Register (Offset = 4000h) [Reset = 11h]
        3. 7.6.8.3  PWM0_IE0 Register (Offset = 4001h) [Reset = 00h]
        4. 7.6.8.4  PWM0_IE1 Register (Offset = 4002h) [Reset = 00h]
        5. 7.6.8.5  PWM0_IR Register (Offset = 4003h) [Reset = 00h]
        6. 7.6.8.6  PWM0_STATUS Register (Offset = 4004h) [Reset = 00h]
        7. 7.6.8.7  PWM0_CUR_PULSE[y] Register (Offset = 4005h + formula) [Reset = 00000000h]
        8. 7.6.8.8  PWM0_CUR_VAL_MSB Register (Offset = 4009h) [Reset = 00h]
        9. 7.6.8.9  PWM0_CUR_VAL_LSB Register (Offset = 400Ah) [Reset = 00h]
        10. 7.6.8.10 PWM0_CONST_MSB Register (Offset = 400Bh) [Reset = 00h]
        11. 7.6.8.11 PWM0_CONST_LSB Register (Offset = 400Ch) [Reset = 00h]
        12. 7.6.8.12 PWM0_STOP_VAL_FRAC_F Register (Offset = 400Dh) [Reset = 00h]
        13. 7.6.8.13 PWM0_STOP_VAL_MSB Register (Offset = 400Eh) [Reset = 00h]
        14. 7.6.8.14 PWM0_STOP_VAL_LSB Register (Offset = 400Fh) [Reset = 00h]
        15. 7.6.8.15 PWM0_STOP_SL_MSB Register (Offset = 4010h) [Reset = 00h]
        16. 7.6.8.16 PWM0_STOP_SL_MID Register (Offset = 4011h) [Reset = 00h]
        17. 7.6.8.17 PWM0_STOP_SL_LSB Register (Offset = 4012h) [Reset = 00h]
        18. 7.6.8.18 PWM0_START_VAL_FRAC_F Register (Offset = 4013h) [Reset = 00h]
        19. 7.6.8.19 PWM0_START_VAL_MSB Register (Offset = 4014h) [Reset = 00h]
        20. 7.6.8.20 PWM0_START_VAL_LSB Register (Offset = 4015h) [Reset = 00h]
        21. 7.6.8.21 PWM0_START_SL_MSB Register (Offset = 4016h) [Reset = 00h]
        22. 7.6.8.22 PWM0_START_SL_MID Register (Offset = 4017h) [Reset = 00h]
        23. 7.6.8.23 PWM0_START_SL_LSB Register (Offset = 4018h) [Reset = 00h]
        24. 7.6.8.24 PWM0_END_VAL_CONST_FRAC_F Register (Offset = 4019h) [Reset = 00h]
        25. 7.6.8.25 PWM0_END_VAL_MSB Register (Offset = 401Ah) [Reset = 00h]
        26. 7.6.8.26 PWM0_END_VAL_LSB Register (Offset = 401Bh) [Reset = 00h]
        27. 7.6.8.27 PWM0_PULSE_STOP_RAMP[y] Register (Offset = 401Ch + formula) [Reset = 00000000h]
        28. 7.6.8.28 PWM0_PULSE_MAX[y] Register (Offset = 4020h + formula) [Reset = 00000000h]
        29. 7.6.8.29 PWM0_ACTION Register (Offset = 4024h) [Reset = 00h]
        30. 7.6.8.30 PWM0_IAS_CTRL Register (Offset = 4030h) [Reset = 00h]
      9. 7.6.9 PWM1 Registers
        1. 7.6.9.1  PWM1_CTRL Register (Offset = 4100h) [Reset = 11h]
        2. 7.6.9.2  PWM1_IE0 Register (Offset = 4101h) [Reset = 00h]
        3. 7.6.9.3  PWM1_IE1 Register (Offset = 4102h) [Reset = 00h]
        4. 7.6.9.4  PWM1_IR Register (Offset = 4103h) [Reset = 00h]
        5. 7.6.9.5  PWM1_STATUS Register (Offset = 4104h) [Reset = 00h]
        6. 7.6.9.6  PWM1_CUR_PULSE[y] Register (Offset = 4105h + formula) [Reset = 00000000h]
        7. 7.6.9.7  PWM1_CUR_VAL_MSB Register (Offset = 4109h) [Reset = 00h]
        8. 7.6.9.8  PWM1_CUR_VAL_LSB Register (Offset = 410Ah) [Reset = 00h]
        9. 7.6.9.9  PWM1_CONST_MSB Register (Offset = 410Bh) [Reset = 00h]
        10. 7.6.9.10 PWM1_CONST_LSB Register (Offset = 410Ch) [Reset = 00h]
        11. 7.6.9.11 PWM1_STOP_VAL_FRAC_F Register (Offset = 410Dh) [Reset = 00h]
        12. 7.6.9.12 PWM1_STOP_VAL_MSB Register (Offset = 410Eh) [Reset = 00h]
        13. 7.6.9.13 PWM1_STOP_VAL_LSB Register (Offset = 410Fh) [Reset = 00h]
        14. 7.6.9.14 PWM1_STOP_SL_MSB Register (Offset = 4110h) [Reset = 00h]
        15. 7.6.9.15 PWM1_STOP_SL_MID Register (Offset = 4111h) [Reset = 00h]
        16. 7.6.9.16 PWM1_STOP_SL_LSB Register (Offset = 4112h) [Reset = 00h]
        17. 7.6.9.17 PWM1_START_VAL_FRAC_F Register (Offset = 4113h) [Reset = 00h]
        18. 7.6.9.18 PWM1_START_VAL_MSB Register (Offset = 4114h) [Reset = 00h]
        19. 7.6.9.19 PWM1_START_VAL_LSB Register (Offset = 4115h) [Reset = 00h]
        20. 7.6.9.20 PWM1_START_SL_MSB Register (Offset = 4116h) [Reset = 00h]
        21. 7.6.9.21 PWM1_START_SL_MID Register (Offset = 4117h) [Reset = 00h]
        22. 7.6.9.22 PWM1_START_SL_LSB Register (Offset = 4118h) [Reset = 00h]
        23. 7.6.9.23 PWM1_END_VAL_CONST_FRAC_F Register (Offset = 4119h) [Reset = 00h]
        24. 7.6.9.24 PWM1_END_VAL_MSB Register (Offset = 411Ah) [Reset = 00h]
        25. 7.6.9.25 PWM1_END_VAL_LSB Register (Offset = 411Bh) [Reset = 00h]
        26. 7.6.9.26 PWM1_PULSE_STOP_RAMP[y] Register (Offset = 411Ch + formula) [Reset = 00000000h]
        27. 7.6.9.27 PWM1_PULSE_MAX[y] Register (Offset = 4120h + formula) [Reset = 00000000h]
        28. 7.6.9.28 PWM1_ACTION Register (Offset = 4124h) [Reset = 00h]
        29. 7.6.9.29 PWM1_IAS_CTRL Register (Offset = 4130h) [Reset = 00h]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Mechanical Data

7.6.4.1 UART_CREL Register (Offset = 2000h) [Reset = 10h]

UART_CREL is shown in Figure 7-82 and described in Table 7-123.

Return to the Summary Table.

UART IP release version

Figure 7-82 UART_CREL Register
76543210
MAJORMINOR
R-1hR-0h
Table 7-123 UART_CREL Register Field Descriptions
BitFieldTypeResetDescription
7-4MAJORR1h The major version number of this revision
3-0MINORR0h The minor version number of this revision