Inicio Controladores para motores Drivers para motores de CC sin escobillas (BLDC) Controladores BLDC
Inicio
Controladores para motores
Drivers para motores de CC sin escobillas (BLDC)
Controladores BLDC
NUEVO

DRV8363-Q1

ACTIVO

Controlador de compuerta automotriz trifásico para baterías de 24 V y 48 V con detección precisa de

Haga su pedido ahora
Hoja de datos

DRV8363-Q1

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Rating Automotive Architecture Gate driver Control interface 1xPWM, 3xPWM, 6xPWM Gate drive (A) 1 Vs (min) (V) 8 Vs ABS (max) (V) 85 Features Current sense Amplifier, SPI/I2C, Watchdog timer Operating temperature range (°C) -40 to 125
Rating Automotive Architecture Gate driver Control interface 1xPWM, 3xPWM, 6xPWM Gate drive (A) 1 Vs (min) (V) 8 Vs ABS (max) (V) 85 Features Current sense Amplifier, SPI/I2C, Watchdog timer Operating temperature range (°C) -40 to 125
VQFN (RGZ) 48 49 mm² 7 x 7
  • AEC-Q100 Test Guidance for automotive applications
    • Device ambient temperature: –40°C to +125°C
  • Three phase half-bridge gate driver
    • Drives six N-channel MOSFETs (NMOS)
    • 8 to 85V wide operating voltage range
    • Bootstrap architecture for high-side gate driver
    • Supports 50mA average gate switching current enables driving 400nC MOSFETs at 20kHz
    • Trickle charge pump to support 100% PWM duty cycle and to generate overdrive supply to drive external cut-off or reverse polarity protection circuit
  • Smart Gate Drive architecture
    • 15-level configurable peak gate drive current up to 1000 / 2000mA (source / sink)
    • Closed-loop automatic deadtime insertion based on gate-source voltage monitoring
    • Configurable soft shutdown to minimize inductive voltage spikes during overcurrent shutdown
  • Low-side Current Sense Amplifier
    • 1mV low input offset across temperature
    • 4-level adjustable gain
    • Adjustable output bias to support unidirectional or bidirectional sensing
  • SPI-based detailed configuration and diagnostics
  • DRVOFF pin to disable driver independently
  • High voltage wake up pin (nSLEEP)
  • Dedicated ASCIN pin to control motor braking (active short circuit)
  • 6x, 3x, 1x, and Independent PWM Modes
  • Supports 3.3V and 5V Logic Inputs
  • Integrated protection features
    • Battery and power supply voltage monitors
    • MOSFET VDS and Rsense over current monitors
    • MOSFET VGS gate fault monitors
    • Device thermal warning and shutdown
    • Fault condition indicator pin
  • AEC-Q100 Test Guidance for automotive applications
    • Device ambient temperature: –40°C to +125°C
  • Three phase half-bridge gate driver
    • Drives six N-channel MOSFETs (NMOS)
    • 8 to 85V wide operating voltage range
    • Bootstrap architecture for high-side gate driver
    • Supports 50mA average gate switching current enables driving 400nC MOSFETs at 20kHz
    • Trickle charge pump to support 100% PWM duty cycle and to generate overdrive supply to drive external cut-off or reverse polarity protection circuit
  • Smart Gate Drive architecture
    • 15-level configurable peak gate drive current up to 1000 / 2000mA (source / sink)
    • Closed-loop automatic deadtime insertion based on gate-source voltage monitoring
    • Configurable soft shutdown to minimize inductive voltage spikes during overcurrent shutdown
  • Low-side Current Sense Amplifier
    • 1mV low input offset across temperature
    • 4-level adjustable gain
    • Adjustable output bias to support unidirectional or bidirectional sensing
  • SPI-based detailed configuration and diagnostics
  • DRVOFF pin to disable driver independently
  • High voltage wake up pin (nSLEEP)
  • Dedicated ASCIN pin to control motor braking (active short circuit)
  • 6x, 3x, 1x, and Independent PWM Modes
  • Supports 3.3V and 5V Logic Inputs
  • Integrated protection features
    • Battery and power supply voltage monitors
    • MOSFET VDS and Rsense over current monitors
    • MOSFET VGS gate fault monitors
    • Device thermal warning and shutdown
    • Fault condition indicator pin

The DRV8363-Q1 is an integrated smart gate driver for 48V automotive three-phase BLDC applications. The device provides three half-bridge gate drivers, each capable of driving high-side and low-side N-channel power MOSFETs. The DRV8363-Q1 generates the correct gate drive voltages using an external 12V supply and an integrated bootstrap diode for the high-side MOSFETs. The Smart Gate Drive architecture supports configurable peak gate drive current from 16mA up to 1A source and 2A sink. The DRV8363-Q1 can operate with a wide input range from 8V to 85V at the motor connection. A trickle charge pump allows for the gate drivers to support 100% PWM duty cycle control and provides overdrive gate drive voltage of external switches.

The DRV8363-Q1 provides low-side current sense amplifiers to support resistor based low-side current sensing. The low offset of the amplifiers enables the system to obtain precise motor current measurements.

A wide range of diagnostics and protection features are integrated with the DRV8363-Q1 enables a robust motor drive system design and helps eliminate the need of external components. The highly configurable device response allows the device to be integrated seamlessly into a variety of system designs.

The DRV8363-Q1 is an integrated smart gate driver for 48V automotive three-phase BLDC applications. The device provides three half-bridge gate drivers, each capable of driving high-side and low-side N-channel power MOSFETs. The DRV8363-Q1 generates the correct gate drive voltages using an external 12V supply and an integrated bootstrap diode for the high-side MOSFETs. The Smart Gate Drive architecture supports configurable peak gate drive current from 16mA up to 1A source and 2A sink. The DRV8363-Q1 can operate with a wide input range from 8V to 85V at the motor connection. A trickle charge pump allows for the gate drivers to support 100% PWM duty cycle control and provides overdrive gate drive voltage of external switches.

The DRV8363-Q1 provides low-side current sense amplifiers to support resistor based low-side current sensing. The low offset of the amplifiers enables the system to obtain precise motor current measurements.

A wide range of diagnostics and protection features are integrated with the DRV8363-Q1 enables a robust motor drive system design and helps eliminate the need of external components. The highly configurable device response allows the device to be integrated seamlessly into a variety of system designs.
filter Buscar otro/a Controladores BLDC
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 5
Tipo Título Fecha
* Data sheet DRV8363-Q1 48V Battery Three-Phase Smart Gate Driver with Accurate Current Sensing and Advanced Monitoring datasheet (Rev. A) PDF | HTML 16 dic 2025
Application brief Understanding Gate Driver Slew Rate Control, MOSFET Switching Optimization and Protection Features (Rev. A) PDF | HTML 11 dic 2025
Application note Motor Driver Slew Rate Considerations for 48V Automotive Systems PDF | HTML 24 nov 2025
Technical article Taking e-bike safety to the next gear with active short circuit technology PDF | HTML 04 sep 2025
Certificate DRV8363-Q1EVM EU Declaration of Conformity (DoC) 11 abr 2025

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

DRV8363-Q1EVM — Módulo de evaluación DRV8363-Q1

El DRV8363-Q1EVM es una etapa de accionamiento de CC trifásica sin escobillas de 30 A basada en el controlador de puerta DRV8363-Q1 para motores BLDC.

El EVM permite evaluar rápidamente el dispositivo DRV8363-Q1, que hace girar un motor BLDC con conmutación y control trapezoidales.

Se incluyen LED (...)

Guía del usuario: PDF | HTML
No disponible en TI.com
Diseños de referencia

TIDA-020094 — Diseño de referencia de zona de 48 V

Este diseño de referencia demuestra las tendencias en las arquitecturas automotrices avanzadas del carril de baja tensión 48 V. El diseño incluye la arquitectura troncal de 48 V y la conversión de potencia de 48 V a 12 V. El diseño de referencia destaca los controladores de carga de 48 V en todos (...)
Design guide: PDF
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
VQFN (RGZ) 48 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos