제품 상세 정보

Number of series cells 1 Charge current (max) (A) 1.5 Vin (max) (V) 9 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (min) (V) 3.5 Battery charge voltage (max) (V) 4.44 Absolute max Vin (max) (V) 20 Control topology Switch-Mode Buck Control interface I2C Features BAT temp thermistor monitoring (hot/cold profile), Input OVP, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Vin (min) (V) 4 Rating Catalog Operating temperature range (°C) -40 to 85
Number of series cells 1 Charge current (max) (A) 1.5 Vin (max) (V) 9 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (min) (V) 3.5 Battery charge voltage (max) (V) 4.44 Absolute max Vin (max) (V) 20 Control topology Switch-Mode Buck Control interface I2C Features BAT temp thermistor monitoring (hot/cold profile), Input OVP, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power) Vin (min) (V) 4 Rating Catalog Operating temperature range (°C) -40 to 85
DSBGA (YFF) 30 5.71999999999999912 mm² 2.2 x 2.5999999999999996
  • High-Efficiency Mini-USB/AC Battery Charger for
    Single-Cell Li-Ion and Li-Polymer Battery Packs
  • Charge Battery and Provide USB-OTG Support at the Same Time
  • High-Accuracy Voltage and Current Regulation
    • Input Current Regulation Accuracy: ±5% (100mA, 500mA)
    • Charge Voltage Regulation Accuracy: ±0.5% (25°C), ±1% (0-125°C)
    • Charge Current Regulation Accuracy: ±5%
  • Boost Mode Operation for USB OTG:
    • Input Voltage Range (from Battery): 2.3V to 4.5V
    • Output for VBUS: 5.05V/500 mA
  • Input Voltage Based Dynamic Power Management Provides
    Protection Against Current Limited Adapters
  • Bad Adaptor Detection and Rejection
  • Safety Limit Register for Added Security by Limiting
    Maximum Charge Voltage and Maximum Charge Current
  • 20-V Absolute Maximum Input Voltage Rating
  • 9.0-V Maximum Operating Input Voltage
  • Charge Faster than Linear Chargers
  • Built-in Input Current Sensing and Limiting
  • Integrated Power FETs for up to 1.5-A Charge Rate
  • Programmable Charge Parameters Through I2C Interface
    (up to 3.4 Mbps):
    • Input Current
    • Fast-Charge/Termination Current
    • Charge Voltage (3.5-4.44V)
    • Safety Timer with Reset Control
    • Safety Timer with Reset Control
    • Termination Enable
  • Synchronous Fixed-Frequency PWM Controller Operating at 3 MHz
    With 0% to 99.5% Duty Cycle
  • Automatic High Impedance Mode for Low Power Consumption
  • Robust Protection
    • Reverse Leakage Protection Prevents Battery Drainage
    • Thermal Regulation and Protection
    • Input/Output Over Voltage Protection
  • Status Output for Charging and Faults
  • USB Friendly Boot-Up Sequence
  • 2.35 × 2.65 mm 30-pin WCSP Package
  • High-Efficiency Mini-USB/AC Battery Charger for
    Single-Cell Li-Ion and Li-Polymer Battery Packs
  • Charge Battery and Provide USB-OTG Support at the Same Time
  • High-Accuracy Voltage and Current Regulation
    • Input Current Regulation Accuracy: ±5% (100mA, 500mA)
    • Charge Voltage Regulation Accuracy: ±0.5% (25°C), ±1% (0-125°C)
    • Charge Current Regulation Accuracy: ±5%
  • Boost Mode Operation for USB OTG:
    • Input Voltage Range (from Battery): 2.3V to 4.5V
    • Output for VBUS: 5.05V/500 mA
  • Input Voltage Based Dynamic Power Management Provides
    Protection Against Current Limited Adapters
  • Bad Adaptor Detection and Rejection
  • Safety Limit Register for Added Security by Limiting
    Maximum Charge Voltage and Maximum Charge Current
  • 20-V Absolute Maximum Input Voltage Rating
  • 9.0-V Maximum Operating Input Voltage
  • Charge Faster than Linear Chargers
  • Built-in Input Current Sensing and Limiting
  • Integrated Power FETs for up to 1.5-A Charge Rate
  • Programmable Charge Parameters Through I2C Interface
    (up to 3.4 Mbps):
    • Input Current
    • Fast-Charge/Termination Current
    • Charge Voltage (3.5-4.44V)
    • Safety Timer with Reset Control
    • Safety Timer with Reset Control
    • Termination Enable
  • Synchronous Fixed-Frequency PWM Controller Operating at 3 MHz
    With 0% to 99.5% Duty Cycle
  • Automatic High Impedance Mode for Low Power Consumption
  • Robust Protection
    • Reverse Leakage Protection Prevents Battery Drainage
    • Thermal Regulation and Protection
    • Input/Output Over Voltage Protection
  • Status Output for Charging and Faults
  • USB Friendly Boot-Up Sequence
  • 2.35 × 2.65 mm 30-pin WCSP Package

The bq24140 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates two synchronous PWM chargers, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on user-selectable minimum current level. A safety timer with reset control provides a safety backup for I2C interface. During normal operation, the IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I2C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to 125°C typical. To support USB OTG device, the IC can provide VBUS (5.05V typical) by boosting the battery voltage. The IC is available in 30-pin WCSP package.

The bq24140 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates two synchronous PWM chargers, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on user-selectable minimum current level. A safety timer with reset control provides a safety backup for I2C interface. During normal operation, the IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I2C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to 125°C typical. To support USB OTG device, the IC can provide VBUS (5.05V typical) by boosting the battery voltage. The IC is available in 30-pin WCSP package.

다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
2개 모두 보기
유형 직함 날짜
* Data sheet 1.5A Dual Input Switchmode Charger with USB-OTG Support datasheet 2011/08/05
Application note BQ241xx/BQ246xx Selection of Multi-Cell Standalone Switching Battery Chargers 2019/12/31

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

지원 소프트웨어

SLUC266 bq24140EVM software

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
배터리 충전기 IC
BQ24140 USB-OTG를 지원하는 1.5A 이중 입력 스위치모드 충전기
거버(Gerber) 파일

bq24140EVM-003 gerbers

SLUC296.ZIP (336 KB)
패키지 CAD 기호, 풋프린트 및 3D 모델
DSBGA (YFF) 30 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상