首頁 電源管理 DC/DC 切換穩壓器 DC/DC 轉換器
首頁
電源管理
DC/DC 切換穩壓器
DC/DC 轉換器

TLV61290

現行

用於單芯鋰離子、富鎳、矽陽極應用的寬電壓電池前端 DC/DC 轉換器

立即訂購
產品規格表

TLV61290

現行
產品規格表 立即訂購

產品詳細資料

Rating Catalog Topology Boost Vin (max) (V) 5.5 Vin (min) (V) 2 Vout (max) (V) 5.5 Vout (min) (V) 2.35 Switch current limit (typ) (A) 11 Features Adjustable current limit, Automatic PWM/PFM transition, Bypass Mode Pass-through Mode, Enable, I2C, Load Disconnect, Output discharge, Spread Spectrum, Synchronous rectification EMI features Spread Spectrum Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.00003 Duty cycle (max) (%) 90
Rating Catalog Topology Boost Vin (max) (V) 5.5 Vin (min) (V) 2 Vout (max) (V) 5.5 Vout (min) (V) 2.35 Switch current limit (typ) (A) 11 Features Adjustable current limit, Automatic PWM/PFM transition, Bypass Mode Pass-through Mode, Enable, I2C, Load Disconnect, Output discharge, Spread Spectrum, Synchronous rectification EMI features Spread Spectrum Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.00003 Duty cycle (max) (%) 90
DSBGA (YBG) 16 2.486929 mm² (1.577 mm × 1.577 mm)
  • Wide VIN range from 2.0V to 5.0V
    • Start up input voltage: 2.2V
  • Programmable average input current limit (3.5A to 8A) via I2C
  • Programmable output voltage (2.35V to 5.0V) via I2C, default 3.4V
  • 97.99% efficiency at VIN = 3.3V, VOUT = 3.4V, IOUT = 1A
  • 95.73% efficiency at VIN = 3.3V, VOUT = 3.4V, IOUT = 3A
  • <300mV undershoot at VIN = 2.7V, VOUT = 3.4V, IOUT = 0A → 3A (0.2A/µs slew rate)
  • Integrated bypass MOSFET (10mΩ), high-side MOSFET (10mΩ), low-side MOSFET (10mΩ)
  • Auto bypass mode when VIN > VOUT
  • Programmable auto PFM operation, Forced PWM operation or Ultrasonic mode operation (avoid audio band noise) during light load condition
  • Spread spectrum modulation and EMI improvement
  • Output discharge function when EN logic is low
  • True disconnection between input and output during shutdown
  • Thermal shutdown and over current protection
  • I2C compatible I/F up to 1Mbps
  • 1.2V I/O logic control interface
  • 16-ball WCSP package
  • Wide VIN range from 2.0V to 5.0V
    • Start up input voltage: 2.2V
  • Programmable average input current limit (3.5A to 8A) via I2C
  • Programmable output voltage (2.35V to 5.0V) via I2C, default 3.4V
  • 97.99% efficiency at VIN = 3.3V, VOUT = 3.4V, IOUT = 1A
  • 95.73% efficiency at VIN = 3.3V, VOUT = 3.4V, IOUT = 3A
  • <300mV undershoot at VIN = 2.7V, VOUT = 3.4V, IOUT = 0A → 3A (0.2A/µs slew rate)
  • Integrated bypass MOSFET (10mΩ), high-side MOSFET (10mΩ), low-side MOSFET (10mΩ)
  • Auto bypass mode when VIN > VOUT
  • Programmable auto PFM operation, Forced PWM operation or Ultrasonic mode operation (avoid audio band noise) during light load condition
  • Spread spectrum modulation and EMI improvement
  • Output discharge function when EN logic is low
  • True disconnection between input and output during shutdown
  • Thermal shutdown and over current protection
  • I2C compatible I/F up to 1Mbps
  • 1.2V I/O logic control interface
  • 16-ball WCSP package

The TLV61290 provides a power supply solution for products powered by a nickel-rich, silicon anode, Li-ion or LiFePO4 battery. The voltage range is optimized for single-cell portable applications like in smart-phones or POS terminal.

Used as a high-power pre-regulator, the device extends the battery run-time and overcomes input current and voltage limitations of the powered system. With a wide input voltage range of 2.0V to 5.0V. Program the output voltage by I2C up to 5.0V, and the default output voltage is 3.4V.

During operation, when the battery is in a good state of charge, the TLV61290 will work in bypass mode, connecting the battery to the power supply system through the bypass FET. If the battery gets to a lower state of charge and its voltage becomes lower than the desired minimum system voltage, the device seamlessly transits into boost mode to use the full battery capacity.

The TLV61290 offers a very small solution size with 16-ball YBG package.

The TLV61290 provides a power supply solution for products powered by a nickel-rich, silicon anode, Li-ion or LiFePO4 battery. The voltage range is optimized for single-cell portable applications like in smart-phones or POS terminal.

Used as a high-power pre-regulator, the device extends the battery run-time and overcomes input current and voltage limitations of the powered system. With a wide input voltage range of 2.0V to 5.0V. Program the output voltage by I2C up to 5.0V, and the default output voltage is 3.4V.

During operation, when the battery is in a good state of charge, the TLV61290 will work in bypass mode, connecting the battery to the power supply system through the bypass FET. If the battery gets to a lower state of charge and its voltage becomes lower than the desired minimum system voltage, the device seamlessly transits into boost mode to use the full battery capacity.

The TLV61290 offers a very small solution size with 16-ball YBG package.
filter 尋找其它 DC/DC 轉換器
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 3
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TLV61290 Wide-Voltage Battery Front-End DC/DC Converter for Single-Cell Li-Ion, Ni-Rich, Si-Anode Applications datasheet (Rev. A) PDF | HTML 2025/11/7
應用說明 Design Considerations in TLV61290 PDF | HTML 2026/6/23
證書 TLV61290EVM EU Declaration of Conformity (DoC) 2025/5/12

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TLV61290EVM — 適用於 5V、10A 升壓轉換器的 TLV61290 評估模組

TLV61290EVM-076 旨在示範 TLV61290 裝置的特性和功能，其為一具旁路模式和 I2C 介面的高效能、高效率同步升壓轉換器。TLV61290EVM 的原廠預設設定允許在 2.0V 至 5.0V 的輸入電壓範圍內運作。所有這些功能都帶來靈活性與設計最佳化，可實現整體性能，以及 BOM 最佳化與設計成本。
使用指南: PDF | HTML
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YBG) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片