SLASFL3 September   2026 DAC90802

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Timing Diagrams
    8. 5.8 Typical Characteristics
      1. 5.8.1 Typical Characteristics: Linearity
      2. 5.8.2 Typical Characteristics: Glitch
      3. 5.8.3 Typical Characteristics: Multiplying Mode
      4. 5.8.4 Typical Characteristics: Fast-Settling Mode
      5. 5.8.5 Typical Characteristics: AWG Mode
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Digital-to-Analog Converters
        1. 6.3.1.1 Reference
        2. 6.3.1.2 Output Span
          1. 6.3.1.2.1 Gain Overrange
        3. 6.3.1.3 Output Synchronization
        4. 6.3.1.4 Thermal Sensors
      2. 6.3.2 Power-On
      3. 6.3.3 Serial Data Interface
        1. 6.3.3.1 SPI Configurations
        2. 6.3.3.2 SPI Stream Mode
        3. 6.3.3.3 SPI Daisy Chain Mode
    4. 6.4 Device Functional Modes
      1. 6.4.1 AWG Mode
      2. 6.4.2 Fast Settling Mode
      3. 6.4.3 Multiplying Mode
  8. 7 Register Maps
    1. 7.1 COMMON Registers
    2. 7.2 HS_DATA Registers
    3. 7.3 HR_DATA Registers
  9. 8 Application and Implementation
    1. 8.1 Application
    2. 8.2 Design Requirements
      1. 8.2.1 Reference Signal Chain Information
        1. 8.2.1.1 DC Reference
        2. 8.2.1.2 AC Reference
      2. 8.2.2 Optimising the Self-Heating Trim to Achieve Lowest THD Across Frequencies for High Voltage Swing
      3. 8.2.3 Digital Interface
      4. 8.2.4 Grounding Recommendations
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Recommendation
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.1 Overview

The DAC90802 is a dual‐channel, 18‐bit, voltage output, digital‐to‐analog converter (DAC) using a proprietary multiplying DAC (MDAC) architecture.

Each channel has an independent full‐featured DAC, including resistor connections for feedback (RFB), offset (ROFS), offset‐adjust (VOSADJ), Load‐DAC (LDAC), temperature sensor outputs (TEMP), references (VREFP, VREFN), and matched reference inversion (REFIN, RCOM).

The channels of the DAC90802 share a quad‐SPI compatible serial data interface, with four data input-output lines (SDIO0-SDIO3), chip‑select (CS), and serial clock (SCLK) inputs. Use the asynchronous active‑low RESET pin to reset DAC codes and the functional state of the device. In addition, use the LDAC inputs to synchronize the DAC outputs with the overall system signals.

The DAC90802 requires external reference voltages. Select among unipolar, biploar, and asymmetric operation using the reference, reference inversion, and offset pin configurations. Configure the offset adjust pin to finetune the offset errors in the overall system. The DAC90802 incorporates a power-on reset (POR) circuit to make sure that the DAC outputs are pulled down to zero using a 5kΩ resistor.