SLASFL3 September   2026 DAC90802

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Timing Diagrams
    8. 5.8 Typical Characteristics
      1. 5.8.1 Typical Characteristics: Linearity
      2. 5.8.2 Typical Characteristics: Glitch
      3. 5.8.3 Typical Characteristics: Multiplying Mode
      4. 5.8.4 Typical Characteristics: Fast-Settling Mode
      5. 5.8.5 Typical Characteristics: AWG Mode
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Digital-to-Analog Converters
        1. 6.3.1.1 Reference
        2. 6.3.1.2 Output Span
          1. 6.3.1.2.1 Gain Overrange
        3. 6.3.1.3 Output Synchronization
        4. 6.3.1.4 Thermal Sensors
      2. 6.3.2 Power-On
      3. 6.3.3 Serial Data Interface
        1. 6.3.3.1 SPI Configurations
        2. 6.3.3.2 SPI Stream Mode
        3. 6.3.3.3 SPI Daisy Chain Mode
    4. 6.4 Device Functional Modes
      1. 6.4.1 AWG Mode
      2. 6.4.2 Fast Settling Mode
      3. 6.4.3 Multiplying Mode
  8. 7 Register Maps
    1. 7.1 COMMON Registers
    2. 7.2 HS_DATA Registers
    3. 7.3 HR_DATA Registers
  9. 8 Application and Implementation
    1. 8.1 Application
    2. 8.2 Design Requirements
      1. 8.2.1 Reference Signal Chain Information
        1. 8.2.1.1 DC Reference
        2. 8.2.1.2 AC Reference
      2. 8.2.2 Optimising the Self-Heating Trim to Achieve Lowest THD Across Frequencies for High Voltage Swing
      3. 8.2.3 Digital Interface
      4. 8.2.4 Grounding Recommendations
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Recommendation
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.3.2 Power-On

The DAC90802 requires multiple power supply rails. The DAC90802 incorporates a power on reset (POR) circuit to make sure that the DAC outputs are pulled down to zero using a 5kΩ resistor.. Asserting an active low signal on RESET resets the device and clears all registers, with the same result as a POR event. While any sequence of power domains followed by reference voltages is usable, the recommended sequence is per Table 6-1.

Table 6-1 Power Supplies and Reference Recommended Sequence
Sequence Purpose Pins
1 Analog High Voltage Negative Rail VEE
2 Analog High Voltage Positive Rail VCC
3 Analog Low Voltage Rail AVDD
4 Digital and Communications Power LVDD, VIO
5 Digital Core Power DVDD
6 References (as used) VREFP, VREFN, REFIN, ROFS, VOSADJ