SLAU278AH May 2009 – March 2021
Figure 4-32 MSP-TS430RHA40A Target Socket Module, Schematic
Figure 4-33 MSP-TS430RHA40A Target Socket Module, PCB| Position | Ref Des | No. per Board | Description | Digi-Key Part No. | Comment |
|---|---|---|---|---|---|
| 1 | C1, C2 | 0 | 12pF, SMD0805 | DNP: C1, C2 | |
| 2 | C5 | 0 | 2.2nF, SMD0805 | DNP C12 | |
| 3 | C3, C7 | 2 | 10uF, 10V, SMD0805 5 | DNP C11 | |
| 4 | C4, C6 | 2 | 100nF, SMD0805 | 478-3351-2-ND | |
| 5 | C9 | 1 | 470nF, SMD0805 | ||
| 6 | D1 | 1 | green LED, SMD0805 | P516TR-ND | |
| 7 | J1, J2, J3, J4 | 4 | 10-pin header, TH | DNP: headers and receptacles enclosed with kit. Keep vias free of solder. | |
| : Header | |||||
| : Receptacle | |||||
| 7.1 | 4 | 10-pin header, TH | DNP: headers and receptacles enclosed with kit. Keep vias free of solder. | ||
| : Header | |||||
| : Receptacle | |||||
| 8 | J5, JP1, JP4, JP5, JP6, JP7, JP8, JP9 | 8 | 3-pin header, male, TH | SAM1035-03-ND | Place jumper on 1-2 of JP4-JP9; Place on 1-2 on JP1 |
| 9 | JP2, JP3 | 2 | 2-pin header, male, TH | SAM1035-02-ND | place jumper on header |
| 10 | 9 | Jumper | 15-38-1024-ND | see Pos 8 an 9 | |
| 11 | JTAG | 1 | 14-pin connector, male, TH | HRP14H-ND | |
| 12 | BOOTST | 0 | 10-pin connector, male, TH | DNP. Keep vias free of solder | |
| 13 | U1 | 1 | Socket: QFN-40B-0.5-01 | Manuf.: Enplas | |
| 14 | Q1 | 0 | Crystal | Micro Crystal MS3V-T1R 32.768kHz, C(Load) = 12.5pF | DNP: Q1. Keep vias free of solder |
| 15 | R1,R7 | 2 | 330R SMD0805 | 541-330ATR-ND | |
| 16 | R2, R3, R5, R6, R8, R9, | 2 | 0 Ohm, SMD0805 | 541-000ATR-ND | DNP:R2, R3, R5, R6 |
| 17 | R4 | 1 | 47k SMD0805 | ||
| 18 | PCB | 1 | 79 x 66 mm | 2 layers | |
| 19 | Rubber stand off | 4 | select appropriate; for example, Buerklin: 20H1724 | apply to corners at bottom side | |
| 20 | MSP430 | 2 | MSP430N5736IRHA | DNP: enclosed with kit. Is supplied by TI |