SLUUDB4 June   2025 TAS5830

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1General Overview
    1. 1.1 Supported Use Cases
  5. 2Process Flows
    1. 2.1  Overview
    2. 2.2  Process Flow 1
      1. 2.2.1  SRC
      2. 2.2.2  Input Mixer
      3. 2.2.3  Equalizer
      4. 2.2.4  Volume
      5. 2.2.5  DPEQ
      6. 2.2.6  3-Band DRC
      7. 2.2.7  AGL
      8. 2.2.8  Clipper
      9. 2.2.9  Output Crossbar
      10. 2.2.10 DSP Memory Map
    3. 2.3  Process Flow 2
      1. 2.3.1 SRC
      2. 2.3.2 Input Mixer
      3. 2.3.3 Equalizer
      4. 2.3.4 Volume
      5. 2.3.5 2-Band DRC
      6. 2.3.6 AGL
      7. 2.3.7 Clipper
      8. 2.3.8 Output Crossbar
      9. 2.3.9 DSP Memory Map
    4. 2.4  Process Flow 3
      1. 2.4.1 SRC
      2. 2.4.2 Input Mixer
      3. 2.4.3 Equalizer
      4. 2.4.4 Volume
      5. 2.4.5 2-Band DRC
      6. 2.4.6 AGL
      7. 2.4.7 Clipper
      8. 2.4.8 Output Crossbar
      9. 2.4.9 DSP Memory Map
    5. 2.5  Process Flow 4
      1. 2.5.1 SRC
      2. 2.5.2 Volume
      3. 2.5.3 DSP Memory Map
    6. 2.6  Process Flow 5
      1. 2.6.1  SRC
      2. 2.6.2  Input Mixer
      3. 2.6.3  Equalizer
      4. 2.6.4  Volume
      5. 2.6.5  DPEQ
      6. 2.6.6  3-Band DRC
      7. 2.6.7  AGL
      8. 2.6.8  Clipper
      9. 2.6.9  Output Crossbar
      10. 2.6.10 DSP Memory Map
    7. 2.7  Process Flow 6
      1. 2.7.1 SRC
      2. 2.7.2 Input Mixer
      3. 2.7.3 Equalizer
      4. 2.7.4 Volume
      5. 2.7.5 2-Band DRC
      6. 2.7.6 AGL
      7. 2.7.7 Clipper
      8. 2.7.8 Output Crossbar
      9. 2.7.9 DSP Memory Map
    8. 2.8  Process Flow 7
      1. 2.8.1 SRC
      2. 2.8.2 Input Mixer
      3. 2.8.3 Equalizer
      4. 2.8.4 Volume
      5. 2.8.5 2-Band DRC
      6. 2.8.6 AGL
      7. 2.8.7 Clipper
      8. 2.8.8 Output Crossbar
      9. 2.8.9 DSP Memory Map
    9. 2.9  Process Flow 8
      1. 2.9.1 SRC
      2. 2.9.2 Volume
      3. 2.9.3 DSP Memory Map
    10. 2.10 Process Flow 9
      1. 2.10.1 SRC
      2. 2.10.2 Input Mixer
      3. 2.10.3 Equalizer
      4. 2.10.4 Volume
      5. 2.10.5 2-Band DRC
      6. 2.10.6 1-Band DRC
      7. 2.10.7 Output Crossbar
      8. 2.10.8 DSP Memory Map
  6. 3Audio Processing Blocks
    1. 3.1 Input Mixer
    2. 3.2 Equalizer
    3. 3.3 Volume
    4. 3.4 DPEQ
      1. 3.4.1 DPEQ
      2. 3.4.2 Energy Sense
      3. 3.4.3 Low Level EQ
      4. 3.4.4 High Level EQ
    5. 3.5 3-Band DRC
      1. 3.5.1 DRC Time Constant
      2. 3.5.2 Crossover
    6. 3.6 2-Band DRC
      1. 3.6.1 DRC Time Constant
      2. 3.6.2 Crossover
    7. 3.7 AGL
    8. 3.8 Clipper
    9. 3.9 Output Crossbar
  7.   A Appendix
    1.     A.1 DSP Memory Map for Process Flows 1 and 5
    2.     A.2 DSP Memory Map for Process Flow 2, 3, 6 and 7
    3.     A.3 DSP Memory Map for Process Flow 4 and 8
    4.     A.4 DSP Memory Map for Process 9

2.10 Process Flow 9

This process flow supports 1.1 speaker configurations with a maximum internal sample rate of 96kHz. It is intended for a tweeter-woofer speaker combination where there are different processing options for the two channels. It is possible to tune the left and right BQs in the 12 BQ bank individually between the tweeter and woofer.

Figure 2-9 depicts the signal path for this flow. The blocks below correspond to the functions found in the PPC3 GUI.

Process Flow 9 Figure 2-9 Process Flow 9