TUSB6250
- Universal Serial Bus (USB)
- Fully compliant with USB 2.0 specification: TID #40390418
- Integrated USB 2.0 UTMI compliant transceiver (PHY)
- Supports USB high speed (HS, 480 Mbits/sec) and full speed (FS, 12 Mbits/sec)
- Supports USB suspend/resume and remote wake-up operation
- Supports USB device-unique serial number by using on-chip unique die ID
- Supports eight configurable endpoints (four input and four output) with a user-programmable buffer size, in addition to the default control endpoint (endpoint 0):
- Each endpoint can be configured for interrupt and bulk (double buffered) transfers.
- All endpoints share the 4K byte data buffer implemented in the SPRAM (single port SRAM).
- Microcontroller Unit (MCU)
- Integrated 60-MHz 8051 microcontroller with two clocks per cycle (up to 30 MIPS)
- Application code is loadable from either the USB host or the external EEPROM (via the I2C interface)
- 8K bytes of ROM for the boot loader
- 1152 bytes of RAM with multiple bank selectable capability for the internal data buffer (IDATA space)
- 40K bytes of RAM, configurable for either code or data space, which provides flexibility to the end product application:
- 32K byte code RAM with 8K byte sector buffer data space
- 16K byte code RAM with 24K byte sector buffer data space
- 8K byte code RAM with 32K byte sector buffer data space
- Master I2C interface controller for external device accesses capable of 100 Kbits/sec or 400 Kbits/sec transfer speed.
- Up to 13 GPIOs and three general-purpose open-drain outputs can be used for end product specific functions.
- ATA/ATAPI Interface Controller
- Supports USB mass storage device class specification bulk-only transfer protocol
- Glueless interface to ATA and ATAPI drives with full ATA and ATAPI protocol support
- High-performance DMA engine supports all PIO, multiword DMA, and UDMA transfer modes up to UDMA mode 4 (UDMA-66 or ATA-66).
- Correctly handles all 13 cases in bulk-only transfer protocol under all supported transfer modes.
- Fully programmable ATA/ATAPI interface access timing
- Provides multiple flexible transfer options to achieve both high-speed transfer by the state machine and high flexibility with MCU involvement:
- Fully-manual transfer (both command and data) by the MCU
- Semi-auto transfer with command transfer by the MCU and data transfer by the state machine
- High-performance fully-auto data transfer mainly by the state machine with few MCU involvements.
- Supports mass-storage devices compatible with the ATA/ATAPI-5 specification:
- Hard-disk drive
- DVD/CD-ROM
- CD-R/W, DVD-R/W
- Compact flash
- PCMCIA type II card or hard drive
- MO drive
- Dual drive support
- Capable of supporting one master and one slave drive in any combination of ATA and ATAPI.
- Provides easy control to put the ATA/ATAPI bus into a 3-state condition through one register bit setting.
- 5-V failsafe I/Os for the ATA/ATAPI interface
- General Features
- Operates on a 24-MHz external crystal with on-chip APLL
- Low-power mode (compliant with bus power requirement of <500 µA)
- 3.3-V operation with 1.8-V core operating voltage provided by an on-chip 1.8-V voltage regulator
- Available in an 80-pin TQFP package
The TUSB6250 is a USB 2.0 HS-capable function controller with an integrated UTMI compliant PHY. The TUSB6250 is intended as a USB 2.0 to ATA/ATAPI bridge for storage devices using a standard ATA or ATAPI interface.
The TUSB6250 is designed to utilize both the fast performance of the state machine and the programmability and flexibility of the embedded microcontroller and firmware. With the elaborative balance between the microcontroller unit (MCU) and the state machine, in addition to its embedded fast MCU (up to 30 MIPS), eight configurable endpoints, up to 40K bytes of configurable code, and data buffer SRAM, the TUSB6250 provides a bridge solution to meet both the performance and flexibility requirement of the next generation external storage devices. With the a low power consumption USB 2.0 integrated PHY, the TUSB6250 also enables the true USB 2.0 high-speed bus-powered application.
기술 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
모두 보기8 | 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TUSB6250 USB 2.0 to ATA/ATAPI Bridge Controller datasheet (Rev. E) | 2008/04/04 | |
| Application note | Using the TUSBxxxx EEPROM Programmer (Rev. B) | 2011/06/09 | ||
| More literature | Home Networking Brochure | 2006/12/21 | ||
| Application note | TUSB6250 Power Supply Sequencing | 2005/02/24 | ||
| Application note | TUSB6250 FAQ (Rev. A) | 2005/01/28 | ||
| Application note | TUSB6250 Bootcode Application Note | 2004/01/07 | ||
| Application note | VIDs, PIDs, and Firmware: Design Decisions When Using TI USB Device Controllers | 2003/09/24 | ||
| Application note | Selection and Specification of Crystals for Texas Instruments USB 2.0 Devices | 2002/12/12 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
시뮬레이션 툴
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI용 PSpice®는 아날로그 회로의 기능을 평가하는 데 사용되는 설계 및 시뮬레이션 환경입니다. 완전한 기능을 갖춘 이 설계 및 시뮬레이션 제품군은 Cadence®의 아날로그 분석 엔진을 사용합니다. 무료로 제공되는 TI용 PSpice에는 아날로그 및 전력 포트폴리오뿐 아니라 아날로그 행동 모델에 이르기까지 업계에서 가장 방대한 모델 라이브러리 중 하나가 포함되어 있습니다.
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
시뮬레이션 툴
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
사용 설명서: PDF
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| TQFP (PFC) | 80 | 옵션 보기 |
주문 및 품질
포함된 정보:
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
포함된 정보:
- 팹 위치
- 조립 위치