SBASAE4 December   2025 ADS125P08

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1  Offset Error Measurement
    2. 6.2  Offset Drift Measurement
    3. 6.3  Gain Error Measurement
    4. 6.4  Gain Drift Measurement
    5. 6.5  NMRR Measurement
    6. 6.6  CMRR Measurement
    7. 6.7  PSRR Measurement
    8. 6.8  SNR Measurement
    9. 6.9  INL Error Measurement
    10. 6.10 THD Measurement
    11. 6.11 SFDR Measurement
    12. 6.12 Noise Performance
    13. 6.13 TUE (Total Unadjusted Error) Measurement
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Input Multiplexer
      2. 7.3.2  High-Impedance Input Buffers
      3. 7.3.3  Input Range
      4. 7.3.4  ADC Reference Voltage
      5. 7.3.5  Power Supplies
        1. 7.3.5.1 AVDD and AVSS
        2. 7.3.5.2 IOVDD
        3. 7.3.5.3 CAPA and CAPD
        4. 7.3.5.4 Power-On Reset (POR)
      6. 7.3.6  Clock Operation
        1. 7.3.6.1 Internal Oscillator
        2. 7.3.6.2 External Clock
      7. 7.3.7  Modulator
      8. 7.3.8  Digital Filter
        1. 7.3.8.1 Digital Filter Latency
        2. 7.3.8.2 Sinc3 and Sinc4 Filters
        3. 7.3.8.3 Sinc4 + Sinc1 Cascade Filter
        4. 7.3.8.4 50/60Hz Notch Filters
      9. 7.3.9  FIFO Buffer
        1. 7.3.9.1 FIFO Buffer Read and Write
        2. 7.3.9.2 FIFO Overflow and Underflow
        3. 7.3.9.3 FIFO Depth Indicator
        4. 7.3.9.4 FIFO Enable and Flush
        5. 7.3.9.5 FIFO Thresholds
      10. 7.3.10 Channel Auto-Sequencer
        1. 7.3.10.1 Auto-Sequencer: Basic Operation
        2. 7.3.10.2 Sequencer Modes
          1. 7.3.10.2.1 Single-Shot Mode
          2. 7.3.10.2.2 Single Step Continuous Conversion Mode
          3. 7.3.10.2.3 Single Sequence Mode
          4. 7.3.10.2.4 Continuous Sequence Mode
        3. 7.3.10.3 Configuring the Auto-Sequencer
        4. 7.3.10.4 Starting and Stopping the Sequencer
        5. 7.3.10.5 Auto-Sequencer and DRDY Behavior
      11. 7.3.11 Offset and Gain Calibration
      12. 7.3.12 General Purpose IOs (GPIOs)
        1. 7.3.12.1 DRDY Output
        2. 7.3.12.2 FAULT Output
      13. 7.3.13 Burn-Out Current Sources
      14. 7.3.14 Open Wire Detection with ADC 0-code output
      15. 7.3.15 System Monitors
        1. 7.3.15.1 Internal Short (Offset Calibration)
        2. 7.3.15.2 Internal Temperature Sensor
        3. 7.3.15.3 External Reference Voltage Readback
        4. 7.3.15.4 Power-Supply Readback
      16. 7.3.16 Monitor Flags, Indicators and Counters
        1. 7.3.16.1  Reset (RESETn flag)
        2. 7.3.16.2  AVDD Undervoltage Monitor (AVDD_UVn flag)
        3. 7.3.16.3  Reference Undervoltage Monitor (REV_UVn flag)
        4. 7.3.16.4  Modulator Overrange Monitor (MOD_OVR_FAULTn flag)
        5. 7.3.16.5  Register Map CRC (REG_MAP_CRC_FAULTn flag)
        6. 7.3.16.6  Memory Map CRC (MEM_INTERNAL_FAULTn flag)
        7. 7.3.16.7  FIFO Overflow (FIFO_OFn flag) and FIFO Underflow (FIFO_UFn flag)
        8. 7.3.16.8  FIFO CRC Fault (FIFO_CRC_FAULTn flag)
        9. 7.3.16.9  GPIO Readback
        10. 7.3.16.10 SPI CRC Fault (SPI_CRC_FAULTn flag)
        11. 7.3.16.11 Register Write Fault (REG_WRITE_FAULTn flag)
        12. 7.3.16.12 DRDY Indicator (DRDY bit)
        13. 7.3.16.13 Sequencer Active Indicator (SEQ_ACTIVE bit)
        14. 7.3.16.14 Sequence Step Indicator (STEP_INDICATOR[4:0])
        15. 7.3.16.15 ADC Conversion Counter (CONV_COUNT[3:0])
        16. 7.3.16.16 FIFO Depth Indicator (FIFO_DEPTH[8:0])
        17. 7.3.16.17 Completed Sequence Counter (SEQ_COUNT[3:0])
      17. 7.3.17 Test DAC (TDAC)
      18. 7.3.18 Parallel Post Filters
        1. 7.3.18.1 Configuring the Parallel Post Filters
        2. 7.3.18.2 Frequency Response of the Parallel Post Filters
        3. 7.3.18.3 Settling Times and DRDY Behavior When Using the Post Filters
        4. 7.3.18.4 Examples of Recommended Post Filter Settings
      19. 7.3.19 Chip Select Forwarding
        1. 7.3.19.1 Configuring the CS forward feature
        2. 7.3.19.2 CS Forward Timeout
        3. 7.3.19.3 CS Forward Header, Frame, and State Diagram
        4. 7.3.19.4 Disabling the CS-FWD mode
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power-Scalable Speed Modes
      2. 7.4.2 Sequencer Functional Modes
      3. 7.4.3 Idle Mode and Standby Mode
      4. 7.4.4 Power-Down Mode
      5. 7.4.5 Reset
        1. 7.4.5.1 RESET Pin
        2. 7.4.5.2 Reset by SPI Register Write
        3. 7.4.5.3 Reset by SPI Input Pattern
      6. 7.4.6 Synchronization
      7. 7.4.7 Conversion-Start Delay Time
    5. 7.5 Programming
      1. 7.5.1  Serial Interface (SPI)
      2. 7.5.2  Serial Interface Signals
        1. 7.5.2.1 Chip Select (CS)
        2. 7.5.2.2 Serial Clock (SCLK)
        3. 7.5.2.3 Serial Data Input (SDI)
        4. 7.5.2.4 Serial Data Output/Data Ready (SDO/DRDY)
        5. 7.5.2.5 Data Ready (DRDY) Pin
      3. 7.5.3  Serial Interface Communication Structure
        1. 7.5.3.1 SPI Frame
        2. 7.5.3.2 STATUS Header
        3. 7.5.3.3 SPI CRC
      4. 7.5.4  Device Commands
        1. 7.5.4.1 No-Operation
        2. 7.5.4.2 Read Conversion Data
        3. 7.5.4.3 Read Register Command
        4. 7.5.4.4 Write Register Command
        5. 7.5.4.5 Read FIFO Buffer Command
      5. 7.5.5  Continuous Read Mode
        1. 7.5.5.1 Read Conversion Data in Continuous Read Mode
        2. 7.5.5.2 Read Registers in Continuous Read Mode
        3. 7.5.5.3 Read FIFO Buffer in Continuous Read Mode
      6. 7.5.6  SPI communication after POR or Reset
      7. 7.5.7  DRDY Pin Behavior
      8. 7.5.8  Daisy-Chain Operation
      9. 7.5.9  3-Wire SPI Mode
        1. 7.5.9.1 3-Wire SPI Mode Frame Re-Align
      10. 7.5.10 Conversion Data
      11. 7.5.11 Data Ready
        1. 7.5.11.1 DRDY Pin and SDO/DRDY Pin
        2. 7.5.11.2 DRDY Bit
        3. 7.5.11.3 Clock Counting
    6. 7.6 Register Map
      1. 7.6.1 ADS125P08 Status and General Configuration Page
      2. 7.6.2 ADS125P08 Step Configuration Page
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Serial Interface Connections
      2. 8.1.2 Interfacing with Multiple Devices
      3. 8.1.3 Unused Inputs and Outputs
      4. 8.1.4 Device Initialization
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Performance Plots - Crosstalk
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Power Supplies
      2. 8.3.2 Power-Supply Sequencing
      3. 8.3.3 Power-Supply Decoupling
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.5.7 DRDY Pin Behavior

This section provides details about the DRDY pin behavior in various scenarios. In all cases, the DRDY_CFG[1:0] bits are reset to 00b. DRDY transitions low whenever new conversion data complete. If DRDY is low when a new conversion completes, then DRDY drives high tw(DRH) before the DRDY falling edge (see Figure 7-63 and Figure 7-65).

The device avoids data corruption if new conversions N+1 complete while conversion data N are being read. Conversion data N+1 are held in an internal buffer until the read of conversion data N is complete. In the following frame, conversion data N+1 are loaded into the SDO output buffer. DRDY does not transition high after conversion data N have been read in this case to indicate that new conversion data N+1 are available for readout (see Figure 7-65).

DRDY transitions high at the eighth SCLK falling edge during conversion data read (Figure 7-62), assuming the STATUS header is disabled. If CS is driven high before the eighth SCLK, then DRDY stays low, indicating that conversion data is not read (Figure 7-63 and Figure 7-64).

Figure 7-64 shows that the same conversion data can be read multiple times until new conversions complete. The conversion counter (CONV_COUNT[3:0] bits in the STATUS_LSB register) indicates if the same data are read again or if new data is read.

Figure 7-66 illustrates that conversion data N+1 are lost when the host does not read the data before conversions N+2 complete. The conversion counter is helpful in this situation to detect if the host missed reading the intermediate conversion results.

ADS125P08 DRDY Pin Behavior: Reading Conversion Data Before New Conversions Complete
A. If the SDO_MODE bit = 0b, the previous state of SDO/DRDY remains until the first SCLK rising edge. Otherwise, SDO/DRDY follows DRDY.
Figure 7-62 DRDY Pin Behavior: Reading Conversion Data Before New Conversions Complete
ADS125P08 DRDY Pin Behavior: Incomplete Read of Conversion Data Before New Conversions Complete
A. If the SDO_MODE bit = 0b, the previous state of SDO/DRDY remains until the first SCLK rising edge. Otherwise, SDO/DRDY follows DRDY.
Figure 7-63 DRDY Pin Behavior: Incomplete Read of Conversion Data Before New Conversions Complete
ADS125P08 DRDY Pin Behavior: Incomplete Read of Conversion Data Followed by Complete Read of Same Conversion Data
A. If the SDO_MODE bit = 0b, the previous state of SDO/DRDY remains until the first SCLK rising edge. Otherwise, SDO/DRDY follows DRDY.
Figure 7-64 DRDY Pin Behavior: Incomplete Read of Conversion Data Followed by Complete Read of Same Conversion Data
ADS125P08 DRDY Pin Behavior: Reading Conversion Data While New Conversions Complete
A. If the SDO_MODE bit = 0b, the previous state of SDO/DRDY remains until the first SCLK rising edge. Otherwise, SDO/DRDY follows DRDY.
Figure 7-65 DRDY Pin Behavior: Reading Conversion Data While New Conversions Complete
ADS125P08 DRDY Pin Behavior: Missed Reading Intermediate Conversion Results
A. If the SDO_MODE bit = 0b, the previous state of SDO/DRDY remains until the first SCLK rising edge. Otherwise, SDO/DRDY follows DRDY.
Figure 7-66 DRDY Pin Behavior: Missed Reading Intermediate Conversion Results

For the following examples, assume that STOP_BEHAVIOR[1:0] = 00b. Setting the STOP bit stops conversions at the last SCLK falling edge within the SPI frame where the CONVERSION_CTRL register is written. However, the DRDY pin does not transition high and old conversion data can still be read until new conversions become available. Figure 7-67 shows the device behavior when setting the STOP bit to abort an ongoing conversion while reading out conversion data. Figure 7-68 shows a scenario where new conversions complete while setting the STOP bit and reading out conversion data.

ADS125P08 DRDY Pin Behavior: Setting the STOP Bit While Reading Conversion Data
A. If the SDO_MODE bit = 0b, the previous state of SDO/DRDY remains until the first SCLK rising edge. Otherwise, SDO/DRDY follows DRDY.
Figure 7-67 DRDY Pin Behavior: Setting the STOP Bit While Reading Conversion Data
ADS125P08 DRDY Pin Behavior: Setting the STOP Bit and Reading Conversion Data While New Conversions Complete
A. If the SDO_MODE bit = 0b, the previous state of SDO/DRDY remains until the first SCLK rising edge. Otherwise, SDO/DRDY follows DRDY.
Figure 7-68 DRDY Pin Behavior: Setting the STOP Bit and Reading Conversion Data While New Conversions Complete