SLASFH8 March   2026 MSPM33C321A-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
    1. 6.1 Pin Diagrams
    2. 6.2 Pin Attributes
      1.      10
    3. 6.3 Signal Descriptions
      1.      12
      2.      13
      3.      14
      4.      15
      5.      16
      6.      17
      7.      18
      8.      19
      9.      20
      10.      21
      11.      22
      12.      23
      13.      24
      14.      25
      15.      26
      16.      27
    4. 6.4 Connections for Unused Pins
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Supply Current Characteristics
      1. 7.5.1 RUN/SLEEP Modes
      2. 7.5.2 STOP/STANDBY Modes
      3. 7.5.3 SHUTDOWN Mode
      4. 7.5.4 VBAT current consumption
    6. 7.6  Flash Memory Characteristics
    7. 7.7  Power Supply Sequencing
      1. 7.7.1 Power Supply Ramp
      2. 7.7.2 POR and BOR
      3. 7.7.3 VBat Characteristics
      4. 7.7.4 Timing Characteristics
    8. 7.8  Clock Specifications
      1. 7.8.1 System Oscillator (SYSOSC)
      2. 7.8.2 High Frequency Crystal/Clock
      3. 7.8.3 System Phase Lock Loop (SYSPLL)
      4. 7.8.4 Low Frequency Oscillator (LFOSC)
      5. 7.8.5 Low Frequency Crystal/Clock
    9. 7.9  Analog Specifications
      1. 7.9.1 ADC Specifications
        1. 7.9.1.1 ADC Electrical Characteristics
        2. 7.9.1.2 ADC Switching Characteristics
        3. 7.9.1.3 ADC Linearity Parameters
        4. 7.9.1.4 Typical Connection Diagram
      2. 7.9.2 COMP Specifications
        1. 7.9.2.1 Comparator Electrical Characteristics
        2. 7.9.2.2 COMP DAC Electrical Characteristics
      3. 7.9.3 VREF Specifications
        1. 7.9.3.1 VREF Voltage Characteristics
        2. 7.9.3.2 VREF Electrical Characteristics
      4. 7.9.4 Analog VBOOST Specification
        1. 7.9.4.1 Analog Mux VBOOST
      5. 7.9.5 Temperature Sensor
    10. 7.10 Serial Interface Specifications
      1. 7.10.1 UART
        1. 7.10.1.1 UART
      2. 7.10.2 I2C
        1. 7.10.2.1 I2C Characteristics
        2. 7.10.2.2 I2C Filter
        3. 7.10.2.3 I2C Timing Diagram
      3. 7.10.3 SPI
        1. 7.10.3.1 SPI
        2. 7.10.3.2 SPI Timing Diagram
      4. 7.10.4 CAN
        1. 7.10.4.1 CAN
      5. 7.10.5 QSPI
        1. 7.10.5.1 QSPI
        2. 7.10.5.2 QSPI Timing Diagram
      6. 7.10.6 I2S/TDM
        1. 7.10.6.1 Serial Audio
        2. 7.10.6.2 I2S/TDM Timing Diagram
    11. 7.11 Digital IO
    12. 7.12 TRNG
      1. 7.12.1 TRNG Electrical Characteristics
      2. 7.12.2 TRNG Switching Characteristics
    13. 7.13 Emulation and Debug
      1. 7.13.1 SWD Timing
  9. 8 Detailed Description
    1. 8.1  Arm Cortex-M33 core with TrustZone and FPU
    2. 8.2  Power Management and Clock Unit (PMCU)
      1. 8.2.1 Power Management Unit (PMU)
      2. 8.2.2 Clock Module (CKM)
      3. 8.2.3 Operating Modes
        1. 8.2.3.1 Functionality by Operating Mode
    3. 8.3  Device Memory Map
      1. 8.3.1 Memory Organization
      2. 8.3.2 Peripheral Memory Map
    4. 8.4  NVIC Interrupt Map
    5. 8.5  Embedded Flash Memory
    6. 8.6  Embedded SRAM
    7. 8.7  DMA
    8. 8.8  Event Manager
    9. 8.9  Error Aggregator Module (EAM)
    10. 8.10 GPIO
    11. 8.11 IOMUX
      1. 8.11.1 Input/Output Diagrams
    12. 8.12 Analog Modules
      1. 8.12.1 HSADC
      2. 8.12.2 COMP
      3. 8.12.3 Temperature Sensor
      4. 8.12.4 VREF
      5. 8.12.5 Device Analog Connections
    13. 8.13 Security and Cryptography
      1. 8.13.1 Global Security Controller (GSC)
      2. 8.13.2 AESADV
      3. 8.13.3 SHA256
      4. 8.13.4 Public Key Algorithm (PKA)
      5. 8.13.5 TRNG
      6. 8.13.6 Keystore
      7. 8.13.7 CRC
    14. 8.14 Serial Communication Interfaces
      1. 8.14.1 UNICOMM (UART/I2C/SPI)
        1. 8.14.1.1 UART (UNICOMM)
        2. 8.14.1.2 I2C (UNICOMM)
        3. 8.14.1.3 SPI (UNICOMM)
      2. 8.14.2 CAN-FD
      3. 8.14.3 Quad SPI (QSPI)
      4. 8.14.4 Digital Audio Interface - I2S/TDM
    15. 8.15 LFSS
    16. 8.16 Timers, RTC and Watchdogs
      1. 8.16.1 Timers (TIMx)
      2. 8.16.2 RTC_A
      3. 8.16.3 IWDT
      4. 8.16.4 WWDT
    17. 8.17 Serial Wire Debug Interface
    18. 8.18 Bootstrap Loader (BSL)
    19. 8.19 Device Factory Constants
    20. 8.20 Identification
  10. 9 Applications, Implementation, and Layout
    1. 9.1 Typical Application
      1. 9.1.1 Schematic
  11. 10Device and Documentation Support
    1. 10.1 Getting Started and Next Steps
    2. 10.2 Device Nomenclature
    3. 10.3 Tools and Software
    4. 10.4 Documentation Support
    5. 10.5 Support Resources
    6. 10.6 Trademarks
    7. 10.7 Electrostatic Discharge Caution
    8. 10.8 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

VREF Electrical Characteristics

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IVREF VREF operating supply current BUFCONFIG = {0, 1}, No load 200 370 µA
IDrive VREF output drive strength (1) Drive strength supported on VREF+ device pin 50 µA
ISC VREF short circuit current 68 TBD mA
TCVREF Temperature coefficient of VREF (Bandgap+VRBUF) (2) 75 ppm/°C
TCdrift Long term VREF drift Time = 1000 hours, BUFCONFIG = {0, 1}, T = 25℃ 300 ppm
PSRRDC VREF Power supply rejection ratio, DC VDD = 1.71 V to VDDmax, BUFCONFIG = 1 57 63 dB
VDD = 2.7 V to VDDmax, BUFCONFIG = 0 49 53
CVREF Recommended ±20% tolerance decoupling capacitor on VREF+ pin (3) (4) 1 µF
tstartup VREF startup time CVREF = 1µF 350 µS
trefresh VREF External capacitor refresh time 31.25
The specified MAX output drive strength is supported regardless of which peripherals are being used in the device.
The temperature coefficient of the VREF output is the sum of TCVRBUF and the temperature coefficient of the internal bandgap reference.
Decoupling capacitor (CVREF) is required when using the internal voltage reference VREF and should be connected from the VREF+ pin to VREF-/GND. When using the VREF+/- pins to supply an external reference, a decoupling capacitor value should be selected based on the external reference source.
The VREF module should only be enabled when CVREF is connected and should not be enabled otherwise.