SLUSFN0A April   2025  – December 2025 BQ25630

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Description (continued)
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Power-On-Reset (POR)
      2. 8.3.2  Device Power Up from Battery
      3. 8.3.3  USB-C Detection
        1. 8.3.3.1 Legacy Adapter Detection
        2. 8.3.3.2 USB-C Dead Battery Mode
        3. 8.3.3.3 SNK Mode
        4. 8.3.3.4 SRC Mode
        5. 8.3.3.5 DRP Mode - Dual Role Port
        6. 8.3.3.6 USB-C Debug Accessory Detection
      4. 8.3.4  Device Power Up from Input Source
        1. 8.3.4.1 REGN LDO Power Up
        2. 8.3.4.2 D+/D– Detection Sets Input Current Limit
        3. 8.3.4.3 Input Voltage Limit Threshold Setting (VINDPM Threshold)
        4. 8.3.4.4 Converter Power-Up
        5. 8.3.4.5 Input Current Optimizer (ICO)
        6. 8.3.4.6 Switching Frequency and Dithering Feature
      5. 8.3.5  Power Path Management
        1. 8.3.5.1 Narrow VDC Architecture
        2. 8.3.5.2 Dynamic Power Management
        3. 8.3.5.3 High Impedance (HIZ) Mode
      6. 8.3.6  Battery Charging Management
        1. 8.3.6.1 Autonomous Charging Cycle
        2. 8.3.6.2 Battery Charging Profile
        3. 8.3.6.3 Charging Termination
        4. 8.3.6.4 Thermistor Qualification
          1. 8.3.6.4.1 Advanced Temperature Profile in Charge Mode
          2. 8.3.6.4.2 TS Pin Thermistor Configuration
          3. 8.3.6.4.3 Cold/Hot Temperature Window in OTG Mode
          4. 8.3.6.4.4 JEITA Charge Rate Scaling
        5. 8.3.6.5 Charging Safety Timers
        6. 8.3.6.6 Alternate Power from Input
      7. 8.3.7  USB On-The-Go (OTG)
        1. 8.3.7.1 Boost OTG Mode
      8. 8.3.8  Integrated 12-bit ADC for Monitoring
      9. 8.3.9  Status Outputs (INT , PG )
        1. 8.3.9.1 PG Pin Power Good Indicator
        2. 8.3.9.2 Interrupts and Status, Flag, and Mask Bits
        3. 8.3.9.3 Interrupt to Host (INT)
      10. 8.3.10 BATFET Control
        1. 8.3.10.1 Shutdown Mode
        2. 8.3.10.2 Ship Mode
        3. 8.3.10.3 Standby Mode
        4. 8.3.10.4 System Power Reset
      11. 8.3.11 Protections
        1. 8.3.11.1 Voltage and Current Monitoring in Battery Only and HIZ Modes
          1. 8.3.11.1.1 Battery Overcurrent Protection
          2. 8.3.11.1.2 Battery Undervoltage Lockout
        2. 8.3.11.2 Voltage and Current Monitoring in Buck Mode
          1. 8.3.11.2.1 Input Overvoltage
          2. 8.3.11.2.2 System Overvoltage Protection (SYSOVP)
          3. 8.3.11.2.3 Forward Converter Cycle-by-Cycle Current Limit
          4. 8.3.11.2.4 System Short
          5. 8.3.11.2.5 Battery Overvoltage Protection (BATOVP)
          6. 8.3.11.2.6 Sleep Comparator
        3. 8.3.11.3 Voltage and Current Monitoring in Boost Mode
          1. 8.3.11.3.1 Boost Mode Overvoltage Protection
          2. 8.3.11.3.2 Boost Mode Duty Cycle Protection
          3. 8.3.11.3.3 Boost Mode PMID Undervoltage Protection
          4. 8.3.11.3.4 Boost Mode Battery Undervoltage
          5. 8.3.11.3.5 Boost Converter Cycle-by-Cycle Current Limit
          6. 8.3.11.3.6 Boost Mode SYS Short
        4. 8.3.11.4 Thermal Regulation and Thermal Shutdown
          1. 8.3.11.4.1 Thermal Protection in Buck Mode
          2. 8.3.11.4.2 Thermal Protection in Boost Mode
          3. 8.3.11.4.3 Thermal Protection in Battery-only Mode
        5. 8.3.11.5 Liquid Detection and Corrosion Mitigation (Patent Pending)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Host Mode and Default Mode
      2. 8.4.2 Register Bit Reset
    5. 8.5 Programming
      1. 8.5.1 Serial Interface
        1. 8.5.1.1 Data Validity
        2. 8.5.1.2 START and STOP Conditions
        3. 8.5.1.3 Byte Format
        4. 8.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 8.5.1.5 Target Address and Data Direction Bit
        6. 8.5.1.6 Single Write and Read
        7. 8.5.1.7 Multi-Write and Multi-Read
    6. 8.6 Register Maps
      1. 8.6.1 Register Programming
      2. 8.6.2 BQ25630 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Inductor Selection
        2. 9.2.2.2 Input Capacitor
        3. 9.2.2.3 Output Capacitor
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Third-Party Products Disclaimer
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 Receiving Notification of Documentation Updates
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information
      2. 12.1.2 Tape and Reel Information
    2. 12.2 Mechanical Data

8.3.10.3 Standby Mode

In standby mode, the BATFET is turned off to prevent the battery from powering the system. The host can place BQ25630 into standby mode by setting BATFET_CTRL = 11b. Standby mode has slightly higher quiescent current than shutdown mode and ship mode, but QON or an I2C command can be used to exit from standby mode. The device is taken out of standby mode by either of these methods:

  • Pulling the QON pin low for tSTANDBY_EXIT
  • Write BATFET_CTRL to 00b via I2C
  • VVBUS > VVBUS_UVLOZ (adapter plug-in)

Standby mode is only entered when the adapter is not present. Setting BATFET_CTRL = 11b while VVBUS > VVBUS_UVLOZ (adapter present) either disables the BATFET or have no immediate effect depending on the setting of BATFET_CTRL_WVBUS.