LM95233

ACTIVE

±2°C Dual Remote and Local Temperature Sensor with TruTherm Technology and SMBus Interface

Top

Product details

Parameters

Local sensor accuracy (Max) (+/- C) 2 Type Remote Operating temperature range (C) -40 to 140 Supply voltage (Min) (V) 3 Interface type I2C, SMBus, 2-Wire Supply voltage (Max) (V) 3.6 Supply current (Max) (uA) 500 Temp resolution (Max) (bits) 11 Features One-shot conversion, ALERT Remote channels (#) 2 Addresses 3 Rating Catalog open-in-new Find other Digital temperature sensors

Package | Pins | Size

WSON (NHL) 14 16 mm² 4 x 4 open-in-new Find other Digital temperature sensors

Features

  • Accurately Senses Die Temperature of 2 Remote ICs or Diode Junctions and Local Temperature
  • TruTherm BJT Beta Compensation Technology Accurately Senses Sub-Micron Process Thermal Diodes
  • 0.125°C LSb Temperature Resolution
  • 0.03125°C LSb Remote Temperature Resolution with Digital Filter Enabled
  • +127.875°C/–128°C and 0°C/255°C Remote Ranges
  • Programmable Digital Filters and Analog Front End Filter
  • Remote Diode Fault Detection, Model Selection and Offset Correction
  • Mask and Status Register Support
  • 3 Programmable TCRIT Outputs with Programmable Shared Hysteresis
  • Programmable Conversion Rate and Shutdown Mode One-Shot Conversion Control
  • SMBus 2.0 Compatible Interface, Supports TIMEOUT
  • Three-Level Address Pin
  • 14-Pin WSON Package

Key Specifications

  • Local Temperature Accuracy: ±2.0 °C (max)
  • Remote Diode Temperature Accuracy: ±0.875 °C (max)
  • Supply Voltage: 3.0 to 3.6 V
  • Average Supply Current (1Hz conversion rate): 0.57 mA (typ)

TruTherm is a trademark of Texas Instruments. All trademarks are the property of their respective owners.

open-in-new Find other Digital temperature sensors

Description

LM95233 is an 11-bit digital temperature sensor with a 2-wire System Management Bus (SMBus) interface that can monitor the temperature of two remote diodes as well as its own temperature. The LM95233 can be used to very accurately monitor the temperature of up to two external devices such as microprocessors, graphics processors or diode-connected 2N3904s. The LM95233's TruTherm BJT beta compensation technology allows sensing of 90nm or 65nm process thermal diodes accurately.

The LM95233 reports temperature in two different formats for +127.875°C/–128°C range and 0°C/255°C range. The LM95233 TCRIT1, TCRIT2 and TCRIT3 outputs are triggered when any unmasked channel exceeds its corresponding programmable limit and can be used to shutdown the system, to turn on the system fans or as a microcontroller interrupt function. The current status of the TCRIT1, TCRIT2 and TCRIT3 pins can be read back from the status registers. Mask registers are available for further control of the TCRIT outputs. LM95233's remote temperature channels have programmable digital filters to minimize unwanted TCRIT events when temperature spikes are encountered.

For optimum flexibility and accuracy each LM95233 channel includes, registers for sub-micron process or 2N3904 diode model selection as well as offset correction. A three level address pin allows connection of up to 3 LM95233s to the same SMBus master. The LM95233 includes power saving functions such as: programmable conversion rate, shutdown mode, and turn off of unused channels.

open-in-new Find other Digital temperature sensors
Download

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 5
Type Title Date
* Datasheet Dual Remote Diode and Local Temp Sensor w/SMBus I/F and TruTherm Technology datasheet (Rev. E) Mar. 22, 2013
Technical articles How to choose the right thermistor for your temperature sensing application Feb. 12, 2020
Technical articles How to enable thermal safety for automotive infotainment and cluster systems Oct. 15, 2019
Technical articles Driving industrial innovation with small-size sensors Sep. 12, 2019
Technical articles How sensor technology is evolving to meet cold chain needs Jun. 18, 2018

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARD Download
1999
Description

RF Sampling 4GSPS ADC with 8GHz DC-Coupled Fully differential Amplifier. Provides a wide bandwidth high performance AC- or DC-coupled capture platform with up to 2 GHz of continous capture bandwidth. Built-in DDC functions enable tuning, down-conversion and bandwidth reduction of captured signals (...)

Features

  • 12-bit 4GSPS ADC - ADC12J4000
  • 8GHz Fully Differential Amplifier - LMH5401
  • 4.8 GHz Low Phase Noise PLL/VCO TRF3765
  • Clock Jitter Cleaner LMK04828
  • Complete TI Power Solution
  • 2GHz Butterworth Low Pass Filter Design

Software development

DRIVER OR LIBRARY Download
Linux Driver for LM95234
LM95234SW-LINUX The Linux driver supports the LM95234 series of Remote and Local Temp Sensors. The Linux driver supports communication through the I2C bus and interfaces with the Hardware Monitoring sub-system.
Linux Mainline Status

Available in Linux Main line: Yes
Available through git.ti.com: N/A

Supported Devices:
  • (...)
DRIVER OR LIBRARY Download
Eval Board Software For Hardware Monitors And Digital Temperature Sensors
SENSOREVAL SensorEval
SensorEval software supports the latest TI temperature sensor and hardware monitor evaluation boards via USB interface. It also allows access to sensors mounted directly on motherboards that support Intel chip sets.

  • Download SensorEval Software and Manual
  • Windows XP support is offered for (...)

Reference designs

Many TI reference designs include the LM95233 Use our reference design selection tool to review and identify designs that best match your application and parameters.

CAD/CAE symbols

Package Pins Download
WSON (NHL) 14 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos