SN65LVDT122

現行

2x2 1.5-Gbps LVDS 交叉點交換器

立即訂購

產品規格表

document-pdfAcrobat SN65LVDS122, SN65LVDT122 - 1.5 Gbps 2 x 2 LVDS Crosspoint Switch datasheet (Rev. B) (英文)

SN65LVDT122

現行

產品規格表

立即訂購

產品詳細資料

Function

Crosspoint

Protocols

CML, LVDS, LVPECL

Number of transmitters

2

Number of receivers

2

Signaling rate (Mbps)

1500

Input signal

CML, LVDS, LVPECL

Output signal

LVDS

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Function

Crosspoint

Protocols

CML, LVDS, LVPECL

Number of transmitters

2

Number of receivers

2

Signaling rate (Mbps)

1500

Input signal

CML, LVDS, LVPECL

Output signal

LVDS

Rating

Catalog

Operating temperature range (°C)

-40 to 85

TSSOP (PW)

16

32 mm² (5 mm × 6.4 mm)

SOIC (D)

16

59.4 mm² (9.9 mm × 6 mm)

Designed for Signaling Rates⁽¹⁾ Up To 1.5 Gbps
Total Jitter < 65 ps
Pin-Compatible With SN65LVDS22 and SN65LVDM22
25 mV of Receiver Input Threshold Hysteresis Over 0-V to 4-V Common-Mode Range
Inputs Electrically Compatible With CML, LVPECL and LVDS Signal Levels
Propagation Delay Times, 900 ps Maximum
LVDT Integrates 110- Terminating Resistor
Offered in SOIC and TSSOP
APPLICATIONS
- 10-G (OC–192) Optical Modules
- 622 MHz Central Office Clock Distribution
- Wireless Basestations
- Low Jitter Clock Repeater/Multiplexer
- Protection Switching for Serial Backplanes

⁽¹⁾The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).

Designed for Signaling Rates⁽¹⁾ Up To 1.5 Gbps
Total Jitter < 65 ps
Pin-Compatible With SN65LVDS22 and SN65LVDM22
25 mV of Receiver Input Threshold Hysteresis Over 0-V to 4-V Common-Mode Range
Inputs Electrically Compatible With CML, LVPECL and LVDS Signal Levels
Propagation Delay Times, 900 ps Maximum
LVDT Integrates 110- Terminating Resistor
Offered in SOIC and TSSOP
APPLICATIONS
- 10-G (OC–192) Optical Modules
- 622 MHz Central Office Clock Distribution
- Wireless Basestations
- Low Jitter Clock Repeater/Multiplexer
- Protection Switching for Serial Backplanes

⁽¹⁾The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).

The SN65LVDS122 and SN65LVDT122 are crosspoint switches that use low voltage differential signaling (LVDS) to achieve signaling rates as high as 1.5 Gbps. They are pin-compatible speed upgrades to the SN65LVDS22 and SN65LVDM22. The internal signal paths maintain differential signaling for high speeds and low signal skews. These devices have a 0 V to 4 V common-mode input range that accepts LVDS, LVPECL, CML inputs. Two logic pins (S0 and S1) set the internal configuration between the differential inputs and outputs. This allows the flexibility to perform the following configurations: 2 x 2 crosspoint switch, 2:1 mux, 1:2 splitter or dual repeater/translator within a single device. Additionally, SN65LVDT122 incorporates a 110- termination resistor for those applications where board space is a premium. Although these devices are designed for 1.5 Gbps, some applications at a 2-Gbps data rate can be supported depending on loading and signal quality.

The intended application of this device is ideal for loopback switching for diagnostic routines, fanout buffering of clock/data distribution provide protection in fault-tolerant systems, clock muxing in optical modules, and for overall signal boosting over extended distances.

The SN65LVDS122 and SN65LVDT122 are characterized for operation from –40°C to 85°C.

The SN65LVDS122 and SN65LVDT122 are crosspoint switches that use low voltage differential signaling (LVDS) to achieve signaling rates as high as 1.5 Gbps. They are pin-compatible speed upgrades to the SN65LVDS22 and SN65LVDM22. The internal signal paths maintain differential signaling for high speeds and low signal skews. These devices have a 0 V to 4 V common-mode input range that accepts LVDS, LVPECL, CML inputs. Two logic pins (S0 and S1) set the internal configuration between the differential inputs and outputs. This allows the flexibility to perform the following configurations: 2 x 2 crosspoint switch, 2:1 mux, 1:2 splitter or dual repeater/translator within a single device. Additionally, SN65LVDT122 incorporates a 110- termination resistor for those applications where board space is a premium. Although these devices are designed for 1.5 Gbps, some applications at a 2-Gbps data rate can be supported depending on loading and signal quality.

The intended application of this device is ideal for loopback switching for diagnostic routines, fanout buffering of clock/data distribution provide protection in fault-tolerant systems, clock muxing in optical modules, and for overall signal boosting over extended distances.

The SN65LVDS122 and SN65LVDT122 are characterized for operation from –40°C to 85°C.

filter

尋找其它 LVDS、M-LVDS 和 PECL IC

下載觀看有字幕稿的影片影片