SLLSFT1 October   2026 TIOM2212

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  L+ Supply Controller
        1. 7.3.1.1 Auto-retry feature
        2. 7.3.1.2 Current sense feature
      2. 7.3.2  C/Q Transceiver
        1. 7.3.2.1 CQ Driver Fault Detection
        2. 7.3.2.2 CQ Reverse Polarity Protection
        3. 7.3.2.3 CQ Current Source or Sink
        4. 7.3.2.4 CQ Receiver Output
        5. 7.3.2.5 CQ Receiver Threshold
        6. 7.3.2.6 CQ/RX Receiver Glitch Filter
      3. 7.3.3  High-side Switch (HSS) Gate Driver
      4. 7.3.4  DI Receiver
      5. 7.3.5  Reverse Polarity Protection
      6. 7.3.6  Thermal Warning and Shutdown
      7. 7.3.7  Clocking
      8. 7.3.8  Power Up Sequence (TIOM2212)
      9. 7.3.9  Device Functional Modes
        1. 7.3.9.1 IO-Link PHY Mode
          1. 7.3.9.1.1 Integrated Automated Sequences
        2. 7.3.9.2 UART Mode
        3. 7.3.9.3 Frame Handler Mode
        4. 7.3.9.4 Extended Frame Handler Mode
      10. 7.3.10 SPI Communication
      11. 7.3.11 SPI Modes and Frame Formats
      12. 7.3.12 Memory and Registry Maps
        1. 7.3.12.1 device Registers
        2. 7.3.12.2 channel Registers
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
    3. 8.3 Power Supply Recommendations
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Tape and Reel Information
    2. 11.2 Mechanical Data

channel Registers

Table 7-37 lists the memory-mapped registers for the channel registers. All register offset addresses not listed in Table 7-37 should be considered as reserved locations and the register contents should not be modified.

Table 7-37 CHANNEL Registers
OffsetAcronymRegister NameSection
0hCQ Driver ConfigurationPhy ConfigSection 3.12.2.1
1hCQ Driver, Receiver ConfigurationPhy ConfigSection 3.12.2.2
2hCQ Driver, DI Receiver ConfigurationPhy ConfigSection 3.12.2.3
3hCQ Driver, Lplus Supply ConfigurationPhy ConfigSection 3.12.2.4
4hLplus Supply ConfigurationPhy ConfigSection 3.12.2.5
5hHigh Side Switch Configuration 0Phy ConfigSection 3.12.2.6
6hHigh Side Switch Configuration 1Phy ConfigSection 3.12.2.7
7hAlternate Function Select ConfigurationPhy ConfigSection 3.12.2.8
8hChannel Logic Interrupt MaskLogic ConfigSection 3.12.2.9
9hChannel Phy Interrupt MaskLogic ConfigSection 3.12.2.10
AhRPD, Offset Timer ConfigurationLogic ConfigSection 3.12.2.11
BhCommon Logic ConfigurationLogic ConfigSection 3.12.2.12
ChIOLink Phy Mode ControlLogic ControlSection 3.12.2.13
DhUART Mode ControlUart DataSection 3.12.2.14
EhFrame Handler Mode ControlFrame Handler Config and ControlSection 3.12.2.15
FhFH + EFH Mode RX Buffer Trigger LevelTrigger Buffer LevelSection 3.12.2.16
10hFH + EFH Mode TX Buffer Trigger LevelCycle TimerSection 3.12.2.17
11hOn Demand data LengthLogic ControlSection 3.12.2.18
12hMaster Process Data LengthLogic ControlSection 3.12.2.19
13hDevice Process Data LengthLogic ControlSection 3.12.2.20
14hFH Mode Cycle Timer ControlLogic ControlSection 3.12.2.21
15hFH Mode DataLogic ControlSection 3.12.2.22
16hChannel Logic StatusMuxed Status (PHY, UART, FH)Section 3.12.2.23
17hChannel Phy StatusPhy Status (Ext CQ, CQ, LP)Section 3.12.2.24
18hChannel Logic Interrupt REQuestMuxed Interrupt Request (PHY, UART, FH)Section 3.12.2.25
19hChannel Physical Interrupt REQuestInterrupt Request (Ext CQ, CQ, LP)Section 3.12.2.26
1AhLED Config 1LED Config / ControlSection 3.12.2.27
1BhLED Config 2LED Config / ControlSection 3.12.2.28
1ChLED Config 3LED Config / ControlSection 3.12.2.29
1DhLED Config 4LED Config / ControlSection 3.12.2.30
1EhLED Config 5LED Config / ControlSection 3.12.2.31
1FhLED Config 6LED Config / ControlSection 3.12.2.32

Complex bit access types are encoded to fit into small table cells. Table 7-38 shows the codes that are used for access types in this section.

Table 7-38 channel Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
RCR
C
Read
to Clear
Write Type
WWWrite
Reset or Default Value
-nValue after reset or the default value

3.12.2.1 CQ Driver Configuration Register (Offset = 0h) [Reset = 00h]

CQ Driver Configuration is shown in Table 7-39.

Return to the Summary Table.

Phy Config

Table 7-39 CQ Driver Configuration Register Field Descriptions
BitFieldTypeResetDescription
7RESERVEDR0h Reserved
6-5CQ_DRV_TSCR/W0h Driver current blanking time Sets the C/Q driver's duration for blanking. See [section] for more information.
  • 0h = 5ms
  • 1h = 15ms
  • 2h = 50ms
  • 3h = 150ms
4-3CQ_DRV_CLIMR/W0h Driver current limit Sets the C/Q driver's output current limit.
  • 0h = 500mA
  • 1h = 300mA
  • 2h = 200mA
  • 3h = 100mA
2-1CQ_DRV_TARR/W0h Driver current auto retry time Sets the C/Q driver's duration to wait after a fault before retrying. See [section] for more information.
  • 0h = 50ms
  • 1h = 500ms
  • 2h = 4s
  • 3h = 10s
0CQ_DRV_AR_DISR/W0h Driver auto retry disable Disables the C/Q driver's attempt to automatically retry.
  • 0h = Driver auto retry enabled
  • 1h = Driver auto retry disabled

3.12.2.2 CQ Driver, Receiver Configuration Register (Offset = 1h) [Reset = 00h]

CQ Driver, Receiver Configuration is shown in Table 7-40.

Return to the Summary Table.

Phy Config

Table 7-40 CQ Driver, Receiver Configuration Register Field Descriptions
BitFieldTypeResetDescription
7CQ_NO_INVR/W0h Disable TX to C/Q and C/Q to RX Inversion
  • 0h = Inversion Enabled
  • 1h = Inversion Disabled
6-5CQ_SNK_SRCR/W0h Driver sink or source current value Sets the C/Q driver's source and sink value while in receive mode.
  • 0h = 5mA
  • 1h = 2 mA
  • 2h = 150uA
  • 3h = Reserved
4CQ_SRC_ENR/W0h Driver current source enable Enables the C/Q driver's high-side current source.
  • 0h = current source disabled
  • 1h = current source enabled
3CQ_SNK_DISR/W0h Driver current sink enable Enables the C/Q driver's low-side current source.
  • 0h = current sink enabled
  • 1h = current sink disabled
2-1CQ_RX_VTH_DISR/W0h C/Q RX threshold select and disable Sets the C/Q pin's type of logic while in receive. See [section] for more information.
  • 0h = Fixed Threshold compliant to IO-Link Standard for all LP range
  • 1h = Ratiomatric threshold for LP less-than 18V, fixed threshold for LP greater-than or equal-to 18V
  • 2h = Type 2/3 threshold
  • 3h = RX disabled
0CQ_GFILT_ENR/W0h C/Q RX glitch filter enable Enables the C/Q pin's receive gltich filtering. See [section] for more information.
  • 0h = CQ RX glitch filter disabled
  • 1h = CQ RX glitch filter enabled

3.12.2.3 CQ Driver, DI Receiver Configuration Register (Offset = 2h) [Reset = 00h]

CQ Driver, DI Receiver Configuration is shown in Table 7-41.

Return to the Summary Table.

Phy Config

Table 7-41 CQ Driver, DI Receiver Configuration Register Field Descriptions
BitFieldTypeResetDescription
7-6CQ_DRV_RISE_FALLR/W0h Driver rise/fall time setting Sets the C/Q driver's rise and fall time.
  • 0h = Rise/fall time set to 400ns nominal
  • 1h = Rise/fall time set to 800ns nominal
  • 2h = Rise/fall time set to 1.6us nominal
  • 3h = Rise/fall time set to 3.2us nominal
5DI_NO_INVR/W0h Disable DI to RX Inversion
  • 0h = Inversion Enabled
  • 1h = Inversion Disabled
4DI_SRC_ENR/W0h DI RX current source enable Enables the DI pin's high-side current source.
  • 0h = 2mA source disabled
  • 1h = 2mA source enabled
3DI_SNK_ENR/W0h DI RX current sink enable Enables the DI pin's low-side current source.
  • 0h = 2mA sink disabled
  • 1h = 2mA sink enabled
2-1DI_RX_VTH_DISR/W0h DI RX threshold select and disable Sets the DI pin's type of logic while in receive. See [section] for more information.
  • 0h = Fixed Threshold compliant to IO-Link Standard for all LP range
  • 1h = Ratiomatric threshold for LP less-than 18V, fixed threshold for LP greater-than or equal-to 18V
  • 2h = Type 2/3 threshold
  • 3h = RX disabled
0DI_GFILT_ENR/W0h DI RX glitch filter enable Enables the DI pin's receive gltich filtering. See [section] for more information.
  • 0h = DI RX glitch filter disabled
  • 1h = DI RX glitch filter enabled

3.12.2.4 CQ Driver, Lplus Supply Configuration Register (Offset = 3h) [Reset = 00h]

CQ Driver, Lplus Supply Configuration is shown in Table 7-42.

Return to the Summary Table.

Phy Config

Table 7-42 CQ Driver, Lplus Supply Configuration Register Field Descriptions
BitFieldTypeResetDescription
7N_DIODE_MDR/W0h N-side blocking diode mode enable
  • 0h = Nside in switch-diode mode
  • 1h = Nside in blocking diode mode
6-5LP_TSCR/W0h L+ current blanking time Sets the L+ driver's duration for blanking. See [section] for more information.
  • 0h = 5ms
  • 1h = 15ms
  • 2h = 50ms
  • 3h = 150ms
4-3LP_CLIMR/W0h L+ current limit Sets the L+ driver's output current limit.
  • 0h = 15mV
  • 1h = 30 mV
  • 2h = 60 mV
  • 3h = 120 mV
2-1LP_TARR/W0h L+ current auto retry time Sets the L+ driver's duration to wait after a fault before retrying. See [section] for more information.
  • 0h = 50ms
  • 1h = 500ms
  • 2h = 4s
  • 3h = 10s
0LP_AR_DISR/W0h L+ auto retry disable Disables the L+ driver's attempt to automatically retry.
  • 0h = LP auto retry enabled
  • 1h = LP auto retry disabled

3.12.2.5 Lplus Supply Configuration Register (Offset = 4h) [Reset = 00h]

Lplus Supply Configuration is shown in Table 7-43.

Return to the Summary Table.

Phy Config

Table 7-43 Lplus Supply Configuration Register Field Descriptions
BitFieldTypeResetDescription
7P_DIODE_MDR/W0h Pside blocking diode mode enable
  • 0h = Pside in switch-diode mode
  • 1h = Pside in blocking diode mode
6-5RESERVEDR0h Reserved
4LP_GATE_DRV_ENR/W0h L+ gate driver enable Enables the external L+ gate driver. See [section] for more information.
  • 0h = LP gate driver disabled
  • 1h = LP gate driver enabled
3LP_SNS_ENR/W0h L+ sense enable Enables the sensing functionality for the external L+ gate driver. See [section] for more information.
  • 0h = LP sense disable
  • 1h = LP sense enable
2LP_DYBL_ENR/W0h L+ dynamic blanking enable Enables dynamic blanking for the external L+ driver. See [section] for more information.
  • 0h = LP dynamic blanking disabled
  • 1h = LP dynamic blanking enabled
1LP_REG_ENR/W0h L+ current regulation loop enable Enables the current regulation loop for the external L+ driver. See [section] for more information.
  • 0h = LP current regulation loop disabled
  • 1h = LP current regulation loop enabled
0LP_GATE_HIZR/W0h L+ gate driver output tristate Sets the external L+ gate driver's output to tristate.
  • 0h = LP gate driver output driven
  • 1h = LP gate driver output tristated

3.12.2.6 High Side Switch Configuration 0 Register (Offset = 5h) [Reset = 00h]

High Side Switch Configuration 0 is shown in Table 7-44.

Return to the Summary Table.

Phy Config

Table 7-44 High Side Switch Configuration 0 Register Field Descriptions
BitFieldTypeResetDescription
7HSS_RP_PROT_ENR/W0h HSS reverse polarity protection enable Enables the high-side switch reverse polarity protection.
  • 0h = HSS Reverse Polarity Protection Disable
  • 1h = HSS Reverse Polarity Protection Enable
6-5HSS_TSCR/W0h HSS current blanking time Sets the external HSS driver's duration for blanking. See [section] for more information.
  • 0h = 5ms
  • 1h = 15ms
  • 2h = 50ms
  • 3h = 150ms
4-3HSS_CLIMR/W0h HSS current limit Sets the external HSS driver's output current limit.
  • 0h = 15mV
  • 1h = 30 mV
  • 2h = 60 mV
  • 3h = 120 mV
2-1HSS_TARR/W0h HSS current auto retry time Sets the external HSS driver's duration to wait after a fault before retrying. See [section] for more information.
  • 0h = 50ms
  • 1h = 500ms
  • 2h = 4s
  • 3h = 10s
0HSS_AR_DISR/W0h HSS auto retry disabled Disables the external HSS driver's attempt to automatically retry.
  • 0h = HSS auto retry enabled
  • 1h = HSS auto retry disabled

3.12.2.7 High Side Switch Configuration 1 Register (Offset = 6h) [Reset = 01h]

High Side Switch Configuration 1 is shown in Table 7-45.

Return to the Summary Table.

Phy Config

Table 7-45 High Side Switch Configuration 1 Register Field Descriptions
BitFieldTypeResetDescription
7HSS_CQG1_STATER/W0h HSS top FET state enable Enables the external HSS top FET state.
  • 0h = HSS top FET state is OFF
  • 1h = HSS top FET state is ON
6HSS_CQG2_STATER/W0h HSS bottom FET state Enables the external HSS bottom FET state.
  • 0h = HSS bottom FET state is OFF
  • 1h = HSS bottom FET state is ON
5-4HSS_SLEWR/W0h HSS switching rate control Sets the external HSS driver's switching rate.
  • 0h = 100 KHz Switching Rate
  • 1h = 10 KHz Switching Rate
  • 2h = Slow Switching
  • 3h = Reserved
3HSS_SNS_ENR/W0h HSS sense enable Enables the sensing functionality for the external HSS gate driver. See [section] for more information.
  • 0h = HSS Sense Disable
  • 1h = HSS Sense Enable
2HSS_DYBL_ENR/W0h HSS dynamic blanking enable Enables dynamic blanking for the external HSS driver. See [section] for more information.
  • 0h = HSS dynamic blanking is disabled
  • 1h = HSS dynamic blanking is enabled
1HSS_REG_ENR/W0h HSS current regulation loop enable Enables the current regulation loop for the external HSS driver. See [section] for more information.
  • 0h = HSS current regulation disabled
  • 1h = HSS current regulation enabled
0HSS_GATE_HIZR/W1h HSS gate driver output tristate Sets the external HSS gate driver's output to tristate.
  • 0h = HSS gate driver output driven
  • 1h = HSS gate driver output tristate

3.12.2.8 Alternate Function Select Configuration Register (Offset = 7h) [Reset = 00h]

Alternate Function Select Configuration is shown in Table 7-46.

Return to the Summary Table.

Phy Config

Table 7-46 Alternate Function Select Configuration Register Field Descriptions
BitFieldTypeResetDescription
7-4RESERVEDR0h Reserved
3LED6_SELR/W0h LED 6 select
  • 0h = Default Function
  • 1h = LED Function
2LED5_SELR/W0h LED 5 select
  • 0h = Default Function
  • 1h = LED Function
1LED4_SELR/W0h LED 4 select
  • 0h = Default Function
  • 1h = LED Function
0LED3_SELR/W0h LED 3 select
  • 0h = Default Function
  • 1h = LED Function

3.12.2.9 Channel Logic Interrupt Mask Register (Offset = 8h) [Reset = 00h]

Channel Logic Interrupt Mask is shown in Table 7-47.

Return to the Summary Table.

Logic Config

Table 7-47 Channel Logic Interrupt Mask Register Field Descriptions
BitFieldTypeResetDescription
7-0MASKR/W0h Channel logic interrupt mask
  • 0h = Do not mask interrupt
  • 1h = Mask interrupt

3.12.2.10 Channel Phy Interrupt Mask Register (Offset = 9h) [Reset = 00h]

Channel Phy Interrupt Mask is shown in Table 7-48.

Return to the Summary Table.

Logic Config

Table 7-48 Channel Phy Interrupt Mask Register Field Descriptions
BitFieldTypeResetDescription
7-0MASKR/W0h Channel physical interrupt mask
  • 0h = Do not mask interrupt
  • 1h = Mask interrupt

3.12.2.11 RPD, Offset Timer Configuration Register (Offset = Ah) [Reset = 00h]

RPD, Offset Timer Configuration is shown in Table 7-49.

Return to the Summary Table.

Logic Config

Table 7-49 RPD, Offset Timer Configuration Register Field Descriptions
BitFieldTypeResetDescription
7-6PSCR/W0h Ready pulse detector or offset prescale Sets offset prescale and ready pulse detection.
  • 0h = OFST - 1us; RPD - 1 ms
  • 1h = OFST - 4.34us; RPD - 10 ms
  • 2h = OFST - 10 us; RPD - 100 ms
  • 3h = OFST - 47.74us; RPD -1 S
5-0COUNTR/W0h Ready pulse detector or offset timer Timeout for Ready Pulse = (COUNT + 1 ) * PSC time unit Offset Time = COUNT * PSC time unit

3.12.2.12 Common Logic Configuration Register (Offset = Bh) [Reset = 00h]

Common Logic Configuration is shown in Table 7-50.

Return to the Summary Table.

Logic Config

Table 7-50 Common Logic Configuration Register Field Descriptions
BitFieldTypeResetDescription
7-6COMR/W0h Channel COM rate Sets the channel COM rate. Applicable to UART and frame handler modes.
  • 0h = Disabled
  • 1h = COM5
  • 2h = COM2
  • 3h = COM3
5-4TAR/W0h Response time (tA) Select Sets the duration that the master PHY will wait for the device's first response until throwing a communication error. Applicable to IOLINK PHY AUTOSTART and frame handler modes.
  • 0h = 10 tBIT
  • 1h = 20 tBIT
  • 2h = 40 tBIT
  • 3h = 80 tBIT
3T2R/W0h Device frame delay (t2) select Sets the duration that the master PHY will wait between device frames until throwing a communication error. Applicable to IOLINK PHY AUTOSTART and frame handler modes.
  • 0h = 3 tBIT
  • 1h = 6 tBIT
2T1R/W0h Master frame delay (t1) select Sets the duration that the master PHY will wait between master frame transmissions. Applicable to IOLINK PHY AUTOSTART and frame handler modes.
  • 0h = 1 tBIT
  • 1h = 2 tBIT
1-0CLMDR/W0h Channel logic mode select Sets the channel's logic mode. See [section] for more information.
  • 0h = phy mode
  • 1h = UART mode
  • 2h = frame handler mode
  • 3h = extended frame handler mode

3.12.2.14 UART Mode Control Register (Offset = Dh) [Reset = 00h]

UART Mode Control is shown in Table 7-52.

Return to the Summary Table.

Logic Control

Table 7-52 UART Mode Control Register Field Descriptions
BitFieldTypeResetDescription
7-0DATAR/W0h UART Data Raw UART data read and write register

3.12.2.15 Frame Handler Mode Control Register (Offset = Eh) [Reset = 00h]

Frame Handler Mode Control is shown in Table 7-53.

Return to the Summary Table.

Logic Control

Table 7-53 Frame Handler Mode Control Register Field Descriptions
BitFieldTypeResetDescription
7FH_RSTR/W0h Frame handler reset Reset frame handler logic and registers
  • 0h = no reset
  • 1h = reset frame handler
6SKIP_CTR/W0h Ignore cycle timer reset during frame handler reset Ignore cycle timer reset while resetting the frame handler logic
  • 0h = reset cycle timer during frame handler reset
  • 1h = no reset
5CKSMR/W0h Enable auto checksum Enables automatic CRC computation for each transmitted message
  • 0h = disable automatic checksum
  • 1h = enable automatic checksum
4TKEEPR/W0h TX buffer keep Enables transmit buffer retention and retransmit functionality
  • 0h = disable TX keep and retransmit
  • 1h = enable TX keep and retransmit
3INT_SYNC_ENR/W0h Internal Frame Handler Sync Enable
  • 0h = Internal Synchronization Disabled
  • 1h = Internal Synchronization Enabled
2EXT_SYNC_ENR/W0h External Frame Handler Sync Enable
  • 0h = External Synchronization Enabled
  • 1h = External Synchronization Disabled
1SYNC_SRC_SELR/W0h External Sync Source Select
  • 0h = TXD[0] is used as external sync
  • 1h = TXD[1] is used as external sync
0SYNC_SRC_EDGER/W0h External Sync Source Edge Select
  • 0h = falling edge of source signal starts sync
  • 1h = rising edge of source signal starts sync

3.12.2.16 FH + EFH Mode RX Buffer Trigger Level Register (Offset = Fh) [Reset = 00h]

FH + EFH Mode RX Buffer Trigger Level is shown in Table 7-54.

Return to the Summary Table.

Logic Control

Table 7-54 FH + EFH Mode RX Buffer Trigger Level Register Field Descriptions
BitFieldTypeResetDescription
7-0RX_BTLVLR/W0h RX Buffer Trigger Level FH: At what RX buffer level the BLVLRT interrupt request will get logged (Rose Above Trigger) EFH: At what RX buffer level the RX_BLVL_RATL interrupt request will get logged

3.12.2.17 FH + EFH Mode TX Buffer Trigger Level Register (Offset = 10h) [Reset = 00h]

FH + EFH Mode TX Buffer Trigger Level is shown in Table 7-55.

Return to the Summary Table.

Logic Control

Table 7-55 FH + EFH Mode TX Buffer Trigger Level Register Field Descriptions
BitFieldTypeResetDescription
7-0TX_BTLVLR/W0h TX Buffer Trigger Level FH: At what TX buffer level the BLVLRT interrupt request will get logged (Fell Below Trigger) EFH: At what TX buffer level the TX_BLVL_FBTL interrupt request will get logged

3.12.2.18 On Demand data Length Register (Offset = 11h) [Reset = 00h]

On Demand data Length is shown in Table 7-56.

Return to the Summary Table.

Logic Control

Table 7-56 On Demand data Length Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5-0LENR/W0h On-demand Data length

3.12.2.19 Master Process Data Length Register (Offset = 12h) [Reset = 00h]

Master Process Data Length is shown in Table 7-57.

Return to the Summary Table.

Logic Control

Table 7-57 Master Process Data Length Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5-0LENR/W0h Master Process Data Length

3.12.2.20 Device Process Data Length Register (Offset = 13h) [Reset = 00h]

Device Process Data Length is shown in Table 7-58.

Return to the Summary Table.

Logic Control

Table 7-58 Device Process Data Length Register Field Descriptions
BitFieldTypeResetDescription
7-6RESERVEDR0h Reserved
5-0LENR/W0h Device Process Data Length

3.12.2.21 FH Mode Cycle Timer Control Register (Offset = 14h) [Reset = 00h]

FH Mode Cycle Timer Control is shown in Table 7-59.

Return to the Summary Table.

Logic Control

Table 7-59 FH Mode Cycle Timer Control Register Field Descriptions
BitFieldTypeResetDescription
7-6BASER/W0h Cycle Timer Base
  • 0h = 100us + no offset
  • 1h = 400us + 6.4ms offset
  • 2h = 1.6ms + 32ms
  • 3h = reserved
5-0MULTR/W0h Cycle Timer Multiplier Cycle Timer Multiplier 0..63 (Valid Values) tCYC = offset + (BASE * MULT)

3.12.2.22 FH Mode Data Register (Offset = 15h) [Reset = 00h]

FH Mode Data is shown in Table 7-60.

Return to the Summary Table.

Logic Control

Table 7-60 FH Mode Data Register Field Descriptions
BitFieldTypeResetDescription
7-0DATAR/W0h Frame Handler Data Read and Write Register Frame Handler Data Read and Write Register

3.12.2.23 Channel Logic Status Register (Offset = 16h) [Reset = 00h]

Channel Logic Status is shown in Table 7-61.

Return to the Summary Table.

Logic Status

Table 7-61 Channel Logic Status Register Field Descriptions
BitFieldTypeResetDescription
7-4RESERVEDR0h Reserved
3DI_RXDR0h DI_RXD Instantaneous value of DI receive pin
  • 0h = DI low
  • 1h = DI high
2-0CLSTATR0h Channel Logic Status Based on channel logic mode phy_mode : CLSTAT[2] - TXEN; CLSTAT[1] - TXD; CLSTAT[0] - RXD uart_mode : N/A fh_mode and extended fh_mode : CLSTAT - Frame Handler State
  • 0h = IDLE
  • 1h = TX
  • 2h = RX
  • 3h = RESERVED
  • 4h = RESERVED
  • 5h = RESERVED
  • 6h = RESERVED
  • 7h = RESERVED

3.12.2.24 Channel Phy Status Register (Offset = 17h) [Reset = 00h]

Channel Phy Status is shown in Table 7-62.

Return to the Summary Table.

Physical Status

Table 7-62 Channel Phy Status Register Field Descriptions
BitFieldTypeResetDescription
7OT_FAULTR0h Over temperature fault Instantaneous value of over temperature fault
  • 0h = no over temperature fault
  • 1h = over temperature fault
6OT_WARNR0h Over temperature warning Instantaneous value of over temperature warning
  • 0h = no over temperature warning
  • 1h = over temperature warning
5EXT_CQ_OCR0h External CQ overcurrent Instantaneous value of external CQ overcurrent
  • 0h = no external CQ overcurrent
  • 1h = external CQ overcurrent
4CQ_OCR0h CQ overcurrent Instantaneous value of CQ overcurrent
  • 0h = no CQ overcurrent
  • 1h = CQ overcurrent
3LP_OCR0h L+ overcurrent Instantaneous value of L+ overcurrent
  • 0h = no L+ overcurrent
  • 1h = L+ overcurrent
2LP_UVLOR0h L+ undervoltage lockout Instantaneous value of L+ undervoltage lockout
  • 0h = no L+ undervoltage lockout
  • 1h = L+ undervoltage lockout
1-0RESERVEDR0h Reserved

3.12.2.25 Channel Logic Interrupt REQuest Register (Offset = 18h) [Reset = 00h]

Channel Logic Interrupt REQuest is shown in Table 7-63.

Return to the Summary Table.

Logic Interrupt

Table 7-63 Channel Logic Interrupt REQuest Register Field Descriptions
BitFieldTypeResetDescription
7CLIREQ7RC0h Channel Logic Interrupt Request 7 Value dependent on channel mode: iolink_phy_mode : ECS_ERR - Establish Communication Sequence Error uart_mode : TX_ERR - Transmission Error fh_mode : TRX_ERR - Transmit (Transmission) or Receive Error (Parity, Frame) ext_fh_mode: TX_ERR - Transmission Error
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
6CLIREQ6RC0h Channel Logic Interrupt Request 6 Value dependent on channel mode: iolink_phy_mode : WPG_ERR - Wake Pulse Generation Error uart_mode : RX_ERR - Reception Error (Parity or Frame) fh_mode : T1_TA_T2_TO_ERR - t1, tA or t2 Timeout Error ext_fh_mode: RX_ERR - Reception Error (Parity or Frame Error)
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
5CLIREQ5RC0h Channel Logic Interrupt Request 5 Value dependent on channel mode: iolink_phy_mode : RPD_ERR - Ready Pulse Detection Error uart_mode : OR_ERR - Over Run Error fh_mode : CKSM_ERR - Check Sum Error (Transmit or Receive Checksum) ext_fh_mode: N/A
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
4CLIREQ4RC0h Channel Logic Interrupt Request 4 Value dependent on channel mode: iolink_phy_mode : ASEQ_OK - Automated Start Sequence Completed without Errors uart_mode : N/A fh_mode : TBUF_EMTY_AT_CT_EXP - Tx Buffer was Empty at Cycle Timer Expiry ext_fh_mode: N/A
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
3CLIREQ3RC0h Channel Logic Interrupt Request 3 Value dependent on channel mode: iolink_phy_mode : N/A uart_mode : N/A fh_mode : SOT - Start Of iolink message Transmission ext_fh_mode: RX_BFULL - Rx Buffer Full
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
2CLIREQ2RC0h Channel Logic Interrupt Request 2 Value dependent on channel mode: iolink_phy_mode : N/A uart_mode : N/A fh_mode : SOR - Start of iolink message Reception ext_fh_mode: TX_BEMPTY - Tx Buffer Empty
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
1CLIREQ1RC0h Channel Logic Interrupt Request 1 Value dependent on channel mode: iolink_phy_mode : CQ_R - CQ Rose uart_mode : TX_RDY - Transmitter Ready fh_mode : BLVL_RT - Buffer Level Reached Trigger level (Both TX and RX) ext_fh_mode: RX_BLVL_RATL - Rx Buffer Level Rose Above Trigger Level
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
0CLIREQ0RC0h Channel Logic Interrupt Request 0 Value dependent on channel mode: iolink_phy_mode : CQ_F - CQ Fell uart_mode : RX_RDY - Receiver Ready (Received byte available for read) fh_mode : MSG_RDY - Message Ready (IO-Link Message received without errors) ext_fh_mode: TX_BLVL_FBTL - Tx Buffer Level Fell Below Trigger Level
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered

3.12.2.26 Channel Physical Interrupt REQuest Register (Offset = 19h) [Reset = 00h]

Channel Physical Interrupt REQuest is shown in Table 7-64.

Return to the Summary Table.

Physical Interrupt

Table 7-64 Channel Physical Interrupt REQuest Register Field Descriptions
BitFieldTypeResetDescription
7OT_FAULTRC0h Over temperature fault Latched (read-to-clear) value of over temperature fault
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
6OT_WARNRC0h Over temperature warning Latched (read-to-clear) value of over temperature warning
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
5EXT_CQ_OCRC0h External CQ overcurrent Latched (read-to-clear) value of external CQ overcurrent
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
4CQ_OCRC0h CQ overcurrent Latched (read-to-clear) value of CQ overcurrent
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
3LP_OCRC0h L+ overcurrent Latched (read-to-clear) value of L+ overcurrent
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
2LP_UVLORC0h L+ undervoltage lockout Latched (read-to-clear) value of L+ undervoltage lockout
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
1DI_RRC0h DI rose Latched (read-to-clear) DI rising edge detected
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered
0DI_FRC0h DI fell Latched (read-to-clear) DI falling edge detected
  • 0h = No interrupt event registered
  • 1h = Interrupt event registered

3.12.2.27 LED Config 1 Register (Offset = 1Ah) [Reset = 00h]

LED Config 1 is shown in Table 7-65.

Return to the Summary Table.

LED Config / Control

Table 7-65 LED Config 1 Register Field Descriptions
BitFieldTypeResetDescription
5-4IDRVR/W0h LED Driver Current Config Sets the current source for LED1.
  • 0h = 2 mA
  • 1h = 8 mA
  • 2h = 14 mA
  • 3h = 20 mA
3-0PWMR/W0h PWM duty cycle configuration Sets the PWM duty cycle for LED1.
  • 0h = 0 % (LED off)
  • 1h = 1.4 %
  • 2h = 1.8 %
  • 3h = 2.5 %
  • 4h = 3.4 %
  • 5h = 4.6 %
  • 6h = 6.3 %
  • 7h = 8.6 %
  • 8h = 11 %
  • 9h = 16 %
  • Ah = 22 %
  • Bh = 29 %
  • Ch = 40 %
  • Dh = 54 %
  • Eh = 74 %
  • Fh = 100 % (LED on)

3.12.2.28 LED Config 2 Register (Offset = 1Bh) [Reset = 00h]

LED Config 2 is shown in Table 7-66.

Return to the Summary Table.

LED Config / Control

Table 7-66 LED Config 2 Register Field Descriptions
BitFieldTypeResetDescription
5-4IDRVR/W0h LED Driver Current Config Sets the current source for LED2.
  • 0h = 2 mA
  • 1h = 8 mA
  • 2h = 14 mA
  • 3h = 20 mA
3-0PWMR/W0h PWM duty cycle configuration Sets the PWM duty cycle for LED2.
  • 0h = 0 % (LED off)
  • 1h = 1.4 %
  • 2h = 1.8 %
  • 3h = 2.5 %
  • 4h = 3.4 %
  • 5h = 4.6 %
  • 6h = 6.3 %
  • 7h = 8.6 %
  • 8h = 11 %
  • 9h = 16 %
  • Ah = 22 %
  • Bh = 29 %
  • Ch = 40 %
  • Dh = 54 %
  • Eh = 74 %
  • Fh = 100 % (LED on)

3.12.2.29 LED Config 3 Register (Offset = 1Ch) [Reset = 00h]

LED Config 3 is shown in Table 7-67.

Return to the Summary Table.

LED Config / Control

Table 7-67 LED Config 3 Register Field Descriptions
BitFieldTypeResetDescription
5-4IDRVR/W0h LED Driver Current Config Sets the current source for LED3.
  • 0h = 2 mA
  • 1h = 8 mA
  • 2h = 14 mA
  • 3h = 20 mA
3-0PWMR/W0h PWM duty cycle configuration Sets the PWM duty cycle for LED3.
  • 0h = 0 % (LED off)
  • 1h = 1.4 %
  • 2h = 1.8 %
  • 3h = 2.5 %
  • 4h = 3.4 %
  • 5h = 4.6 %
  • 6h = 6.3 %
  • 7h = 8.6 %
  • 8h = 11 %
  • 9h = 16 %
  • Ah = 22 %
  • Bh = 29 %
  • Ch = 40 %
  • Dh = 54 %
  • Eh = 74 %
  • Fh = 100 % (LED on)

3.12.2.30 LED Config 4 Register (Offset = 1Dh) [Reset = 00h]

LED Config 4 is shown in Table 7-68.

Return to the Summary Table.

LED Config / Control

Table 7-68 LED Config 4 Register Field Descriptions
BitFieldTypeResetDescription
5-4IDRVR/W0h LED Driver Current Config Sets the current source for LED4.
  • 0h = 2 mA
  • 1h = 8 mA
  • 2h = 14 mA
  • 3h = 20 mA
3-0PWMR/W0h PWM duty cycle configuration Sets the PWM duty cycle for LED4.
  • 0h = 0 % (LED off)
  • 1h = 1.4 %
  • 2h = 1.8 %
  • 3h = 2.5 %
  • 4h = 3.4 %
  • 5h = 4.6 %
  • 6h = 6.3 %
  • 7h = 8.6 %
  • 8h = 11 %
  • 9h = 16 %
  • Ah = 22 %
  • Bh = 29 %
  • Ch = 40 %
  • Dh = 54 %
  • Eh = 74 %
  • Fh = 100 % (LED on)

3.12.2.31 LED Config 5 Register (Offset = 1Eh) [Reset = 00h]

LED Config 5 is shown in Table 7-69.

Return to the Summary Table.

LED Config / Control

Table 7-69 LED Config 5 Register Field Descriptions
BitFieldTypeResetDescription
5-4IDRVR/W0h LED Driver Current Config Sets the current source for LED5.
  • 0h = 2 mA
  • 1h = 8 mA
  • 2h = 14 mA
  • 3h = 20 mA
3-0PWMR/W0h PWM duty cycle configuration Sets the PWM duty cycle for LED5.
  • 0h = 0 % (LED off)
  • 1h = 1.4 %
  • 2h = 1.8 %
  • 3h = 2.5 %
  • 4h = 3.4 %
  • 5h = 4.6 %
  • 6h = 6.3 %
  • 7h = 8.6 %
  • 8h = 11 %
  • 9h = 16 %
  • Ah = 22 %
  • Bh = 29 %
  • Ch = 40 %
  • Dh = 54 %
  • Eh = 74 %
  • Fh = 100 % (LED on)

3.12.2.32 LED Config 6 Register (Offset = 1Fh) [Reset = 00h]

LED Config 6 is shown in Table 7-70.

Return to the Summary Table.

LED Config / Control

Table 7-70 LED Config 6 Register Field Descriptions
BitFieldTypeResetDescription
5-4IDRVR/W0h LED Driver Current Config Sets the current source for LED6.
  • 0h = 2 mA
  • 1h = 8 mA
  • 2h = 14 mA
  • 3h = 20 mA
3-0PWMR/W0h PWM duty cycle configuration Sets the PWM duty cycle for LED6.
  • 0h = 0 % (LED off)
  • 1h = 1.4 %
  • 2h = 1.8 %
  • 3h = 2.5 %
  • 4h = 3.4 %
  • 5h = 4.6 %
  • 6h = 6.3 %
  • 7h = 8.6 %
  • 8h = 11 %
  • 9h = 16 %
  • Ah = 22 %
  • Bh = 29 %
  • Ch = 40 %
  • Dh = 54 %
  • Eh = 74 %
  • Fh = 100 % (LED on)