SLLSFT1 October 2026 TIOM2212
ADVANCE INFORMATION
Table 7-37 lists the memory-mapped registers for the channel registers. All register offset addresses not listed in Table 7-37 should be considered as reserved locations and the register contents should not be modified.
| Offset | Acronym | Register Name | Section |
|---|---|---|---|
| 0h | CQ Driver Configuration | Phy Config | Section 3.12.2.1 |
| 1h | CQ Driver, Receiver Configuration | Phy Config | Section 3.12.2.2 |
| 2h | CQ Driver, DI Receiver Configuration | Phy Config | Section 3.12.2.3 |
| 3h | CQ Driver, Lplus Supply Configuration | Phy Config | Section 3.12.2.4 |
| 4h | Lplus Supply Configuration | Phy Config | Section 3.12.2.5 |
| 5h | High Side Switch Configuration 0 | Phy Config | Section 3.12.2.6 |
| 6h | High Side Switch Configuration 1 | Phy Config | Section 3.12.2.7 |
| 7h | Alternate Function Select Configuration | Phy Config | Section 3.12.2.8 |
| 8h | Channel Logic Interrupt Mask | Logic Config | Section 3.12.2.9 |
| 9h | Channel Phy Interrupt Mask | Logic Config | Section 3.12.2.10 |
| Ah | RPD, Offset Timer Configuration | Logic Config | Section 3.12.2.11 |
| Bh | Common Logic Configuration | Logic Config | Section 3.12.2.12 |
| Ch | IOLink Phy Mode Control | Logic Control | Section 3.12.2.13 |
| Dh | UART Mode Control | Uart Data | Section 3.12.2.14 |
| Eh | Frame Handler Mode Control | Frame Handler Config and Control | Section 3.12.2.15 |
| Fh | FH + EFH Mode RX Buffer Trigger Level | Trigger Buffer Level | Section 3.12.2.16 |
| 10h | FH + EFH Mode TX Buffer Trigger Level | Cycle Timer | Section 3.12.2.17 |
| 11h | On Demand data Length | Logic Control | Section 3.12.2.18 |
| 12h | Master Process Data Length | Logic Control | Section 3.12.2.19 |
| 13h | Device Process Data Length | Logic Control | Section 3.12.2.20 |
| 14h | FH Mode Cycle Timer Control | Logic Control | Section 3.12.2.21 |
| 15h | FH Mode Data | Logic Control | Section 3.12.2.22 |
| 16h | Channel Logic Status | Muxed Status (PHY, UART, FH) | Section 3.12.2.23 |
| 17h | Channel Phy Status | Phy Status (Ext CQ, CQ, LP) | Section 3.12.2.24 |
| 18h | Channel Logic Interrupt REQuest | Muxed Interrupt Request (PHY, UART, FH) | Section 3.12.2.25 |
| 19h | Channel Physical Interrupt REQuest | Interrupt Request (Ext CQ, CQ, LP) | Section 3.12.2.26 |
| 1Ah | LED Config 1 | LED Config / Control | Section 3.12.2.27 |
| 1Bh | LED Config 2 | LED Config / Control | Section 3.12.2.28 |
| 1Ch | LED Config 3 | LED Config / Control | Section 3.12.2.29 |
| 1Dh | LED Config 4 | LED Config / Control | Section 3.12.2.30 |
| 1Eh | LED Config 5 | LED Config / Control | Section 3.12.2.31 |
| 1Fh | LED Config 6 | LED Config / Control | Section 3.12.2.32 |
Complex bit access types are encoded to fit into small table cells. Table 7-38 shows the codes that are used for access types in this section.
| Access Type | Code | Description |
|---|---|---|
| Read Type | ||
| R | R | Read |
| RC | R C | Read to Clear |
| Write Type | ||
| W | W | Write |
| Reset or Default Value | ||
| -n | Value after reset or the default value | |
CQ Driver Configuration is shown in Table 7-39.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | RESERVED | R | 0h | Reserved |
| 6-5 | CQ_DRV_TSC | R/W | 0h | Driver current blanking time
Sets the C/Q driver's duration for blanking. See [section] for more information.
|
| 4-3 | CQ_DRV_CLIM | R/W | 0h | Driver current limit
Sets the C/Q driver's output current limit.
|
| 2-1 | CQ_DRV_TAR | R/W | 0h | Driver current auto retry time
Sets the C/Q driver's duration to wait after a fault before retrying. See [section] for more information.
|
| 0 | CQ_DRV_AR_DIS | R/W | 0h | Driver auto retry disable
Disables the C/Q driver's attempt to automatically retry.
|
CQ Driver, Receiver Configuration is shown in Table 7-40.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | CQ_NO_INV | R/W | 0h | Disable TX to C/Q and C/Q to RX Inversion
|
| 6-5 | CQ_SNK_SRC | R/W | 0h | Driver sink or source current value
Sets the C/Q driver's source and sink value while in receive mode.
|
| 4 | CQ_SRC_EN | R/W | 0h | Driver current source enable
Enables the C/Q driver's high-side current source.
|
| 3 | CQ_SNK_DIS | R/W | 0h | Driver current sink enable
Enables the C/Q driver's low-side current source.
|
| 2-1 | CQ_RX_VTH_DIS | R/W | 0h | C/Q RX threshold select and disable
Sets the C/Q pin's type of logic while in receive. See [section] for more information.
|
| 0 | CQ_GFILT_EN | R/W | 0h | C/Q RX glitch filter enable
Enables the C/Q pin's receive gltich filtering. See [section] for more information.
|
CQ Driver, DI Receiver Configuration is shown in Table 7-41.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | CQ_DRV_RISE_FALL | R/W | 0h | Driver rise/fall time setting
Sets the C/Q driver's rise and fall time.
|
| 5 | DI_NO_INV | R/W | 0h | Disable DI to RX Inversion
|
| 4 | DI_SRC_EN | R/W | 0h | DI RX current source enable
Enables the DI pin's high-side current source.
|
| 3 | DI_SNK_EN | R/W | 0h | DI RX current sink enable
Enables the DI pin's low-side current source.
|
| 2-1 | DI_RX_VTH_DIS | R/W | 0h | DI RX threshold select and disable
Sets the DI pin's type of logic while in receive. See [section] for more information.
|
| 0 | DI_GFILT_EN | R/W | 0h | DI RX glitch filter enable
Enables the DI pin's receive gltich filtering. See [section] for more information.
|
CQ Driver, Lplus Supply Configuration is shown in Table 7-42.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | N_DIODE_MD | R/W | 0h | N-side blocking diode mode enable
|
| 6-5 | LP_TSC | R/W | 0h | L+ current blanking time
Sets the L+ driver's duration for blanking. See [section] for more information.
|
| 4-3 | LP_CLIM | R/W | 0h | L+ current limit
Sets the L+ driver's output current limit.
|
| 2-1 | LP_TAR | R/W | 0h | L+ current auto retry time
Sets the L+ driver's duration to wait after a fault before retrying. See [section] for more information.
|
| 0 | LP_AR_DIS | R/W | 0h | L+ auto retry disable
Disables the L+ driver's attempt to automatically retry.
|
Lplus Supply Configuration is shown in Table 7-43.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | P_DIODE_MD | R/W | 0h | Pside blocking diode mode enable
|
| 6-5 | RESERVED | R | 0h | Reserved |
| 4 | LP_GATE_DRV_EN | R/W | 0h | L+ gate driver enable
Enables the external L+ gate driver. See [section] for more information.
|
| 3 | LP_SNS_EN | R/W | 0h | L+ sense enable
Enables the sensing functionality for the external L+ gate driver. See [section] for more information.
|
| 2 | LP_DYBL_EN | R/W | 0h | L+ dynamic blanking enable
Enables dynamic blanking for the external L+ driver. See [section] for more information.
|
| 1 | LP_REG_EN | R/W | 0h | L+ current regulation loop enable
Enables the current regulation loop for the external L+ driver. See [section] for more information.
|
| 0 | LP_GATE_HIZ | R/W | 0h | L+ gate driver output tristate
Sets the external L+ gate driver's output to tristate.
|
High Side Switch Configuration 0 is shown in Table 7-44.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | HSS_RP_PROT_EN | R/W | 0h | HSS reverse polarity protection enable
Enables the high-side switch reverse polarity protection.
|
| 6-5 | HSS_TSC | R/W | 0h | HSS current blanking time
Sets the external HSS driver's duration for blanking. See [section] for more information.
|
| 4-3 | HSS_CLIM | R/W | 0h | HSS current limit
Sets the external HSS driver's output current limit.
|
| 2-1 | HSS_TAR | R/W | 0h | HSS current auto retry time
Sets the external HSS driver's duration to wait after a fault before retrying. See [section] for more information.
|
| 0 | HSS_AR_DIS | R/W | 0h | HSS auto retry disabled
Disables the external HSS driver's attempt to automatically retry.
|
High Side Switch Configuration 1 is shown in Table 7-45.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | HSS_CQG1_STATE | R/W | 0h | HSS top FET state enable
Enables the external HSS top FET state.
|
| 6 | HSS_CQG2_STATE | R/W | 0h | HSS bottom FET state
Enables the external HSS bottom FET state.
|
| 5-4 | HSS_SLEW | R/W | 0h | HSS switching rate control
Sets the external HSS driver's switching rate.
|
| 3 | HSS_SNS_EN | R/W | 0h | HSS sense enable
Enables the sensing functionality for the external HSS gate driver. See [section] for more information.
|
| 2 | HSS_DYBL_EN | R/W | 0h | HSS dynamic blanking enable
Enables dynamic blanking for the external HSS driver. See [section] for more information.
|
| 1 | HSS_REG_EN | R/W | 0h | HSS current regulation loop enable
Enables the current regulation loop for the external HSS driver. See [section] for more information.
|
| 0 | HSS_GATE_HIZ | R/W | 1h | HSS gate driver output tristate
Sets the external HSS gate driver's output to tristate.
|
Alternate Function Select Configuration is shown in Table 7-46.
Return to the Summary Table.
Phy Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-4 | RESERVED | R | 0h | Reserved |
| 3 | LED6_SEL | R/W | 0h | LED 6 select
|
| 2 | LED5_SEL | R/W | 0h | LED 5 select
|
| 1 | LED4_SEL | R/W | 0h | LED 4 select
|
| 0 | LED3_SEL | R/W | 0h | LED 3 select
|
Channel Logic Interrupt Mask is shown in Table 7-47.
Return to the Summary Table.
Logic Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | MASK | R/W | 0h | Channel logic interrupt mask
|
Channel Phy Interrupt Mask is shown in Table 7-48.
Return to the Summary Table.
Logic Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | MASK | R/W | 0h | Channel physical interrupt mask
|
RPD, Offset Timer Configuration is shown in Table 7-49.
Return to the Summary Table.
Logic Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | PSC | R/W | 0h | Ready pulse detector or offset prescale
Sets offset prescale and ready pulse detection.
|
| 5-0 | COUNT | R/W | 0h | Ready pulse detector or offset timer Timeout for Ready Pulse = (COUNT + 1 ) * PSC time unit Offset Time = COUNT * PSC time unit |
Common Logic Configuration is shown in Table 7-50.
Return to the Summary Table.
Logic Config
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | COM | R/W | 0h | Channel COM rate
Sets the channel COM rate.
Applicable to UART and frame handler modes.
|
| 5-4 | TA | R/W | 0h | Response time (tA) Select
Sets the duration that the master PHY will wait for the device's first response until throwing a communication error.
Applicable to IOLINK PHY AUTOSTART and frame handler modes.
|
| 3 | T2 | R/W | 0h | Device frame delay (t2) select
Sets the duration that the master PHY will wait between device frames until throwing a communication error.
Applicable to IOLINK PHY AUTOSTART and frame handler modes.
|
| 2 | T1 | R/W | 0h | Master frame delay (t1) select
Sets the duration that the master PHY will wait between master frame transmissions.
Applicable to IOLINK PHY AUTOSTART and frame handler modes.
|
| 1-0 | CLMD | R/W | 0h | Channel logic mode select
Sets the channel's logic mode. See [section] for more information.
|
IOLink Phy Mode Control is shown in Table 7-51.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-5 | AUTO_START | R/W | 0h | Auto-start sequence select
Sets the sequence that is executed once device initialization is complete. See [section] for more information.
|
| 4 | CQSRC | R/W | 0h | CQ Source Select
Selects the C/Q driver source in IOLINK PHY mode.
|
| 3-2 | CQ_MD | R/W | 0h | CQ Mode Select with Disable
Selects the C/Q mode when the internal driver is selected.
|
| 1 | CQ_TXD | R/W | 0h | CQ TXD
Sets C/Q driver state when both in IOLINK PHY mode andbit CQSRC is set to SPI register field control
|
| 0 | CQ_TXEN | R/W | 0h | CQ TXEN
Sets C/Q driver enable state when both in IOLINK PHY mode andbit CQSRC is set to SPI register field control
|
UART Mode Control is shown in Table 7-52.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | DATA | R/W | 0h | UART Data Raw UART data read and write register |
Frame Handler Mode Control is shown in Table 7-53.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | FH_RST | R/W | 0h | Frame handler reset
Reset frame handler logic and registers
|
| 6 | SKIP_CT | R/W | 0h | Ignore cycle timer reset during frame handler reset
Ignore cycle timer reset while resetting the frame handler logic
|
| 5 | CKSM | R/W | 0h | Enable auto checksum
Enables automatic CRC computation for each transmitted message
|
| 4 | TKEEP | R/W | 0h | TX buffer keep
Enables transmit buffer retention and retransmit functionality
|
| 3 | INT_SYNC_EN | R/W | 0h | Internal Frame Handler Sync Enable
|
| 2 | EXT_SYNC_EN | R/W | 0h | External Frame Handler Sync Enable
|
| 1 | SYNC_SRC_SEL | R/W | 0h | External Sync Source Select
|
| 0 | SYNC_SRC_EDGE | R/W | 0h | External Sync Source Edge Select
|
FH + EFH Mode RX Buffer Trigger Level is shown in Table 7-54.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | RX_BTLVL | R/W | 0h | RX Buffer Trigger Level FH: At what RX buffer level the BLVLRT interrupt request will get logged (Rose Above Trigger) EFH: At what RX buffer level the RX_BLVL_RATL interrupt request will get logged |
FH + EFH Mode TX Buffer Trigger Level is shown in Table 7-55.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | TX_BTLVL | R/W | 0h | TX Buffer Trigger Level FH: At what TX buffer level the BLVLRT interrupt request will get logged (Fell Below Trigger) EFH: At what TX buffer level the TX_BLVL_FBTL interrupt request will get logged |
On Demand data Length is shown in Table 7-56.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | RESERVED | R | 0h | Reserved |
| 5-0 | LEN | R/W | 0h | On-demand Data length |
Master Process Data Length is shown in Table 7-57.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | RESERVED | R | 0h | Reserved |
| 5-0 | LEN | R/W | 0h | Master Process Data Length |
Device Process Data Length is shown in Table 7-58.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | RESERVED | R | 0h | Reserved |
| 5-0 | LEN | R/W | 0h | Device Process Data Length |
FH Mode Cycle Timer Control is shown in Table 7-59.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | BASE | R/W | 0h | Cycle Timer Base
|
| 5-0 | MULT | R/W | 0h | Cycle Timer Multiplier Cycle Timer Multiplier 0..63 (Valid Values) tCYC = offset + (BASE * MULT) |
FH Mode Data is shown in Table 7-60.
Return to the Summary Table.
Logic Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-0 | DATA | R/W | 0h | Frame Handler Data Read and Write Register Frame Handler Data Read and Write Register |
Channel Logic Status is shown in Table 7-61.
Return to the Summary Table.
Logic Status
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-4 | RESERVED | R | 0h | Reserved |
| 3 | DI_RXD | R | 0h | DI_RXD
Instantaneous value of DI receive pin
|
| 2-0 | CLSTAT | R | 0h | Channel Logic Status
Based on channel logic mode
phy_mode : CLSTAT[2] - TXEN; CLSTAT[1] - TXD; CLSTAT[0] - RXD
uart_mode : N/A
fh_mode and extended fh_mode : CLSTAT - Frame Handler State
|
Channel Phy Status is shown in Table 7-62.
Return to the Summary Table.
Physical Status
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | OT_FAULT | R | 0h | Over temperature fault
Instantaneous value of over temperature fault
|
| 6 | OT_WARN | R | 0h | Over temperature warning
Instantaneous value of over temperature warning
|
| 5 | EXT_CQ_OC | R | 0h | External CQ overcurrent
Instantaneous value of external CQ overcurrent
|
| 4 | CQ_OC | R | 0h | CQ overcurrent
Instantaneous value of CQ overcurrent
|
| 3 | LP_OC | R | 0h | L+ overcurrent
Instantaneous value of L+ overcurrent
|
| 2 | LP_UVLO | R | 0h | L+ undervoltage lockout
Instantaneous value of L+ undervoltage lockout
|
| 1-0 | RESERVED | R | 0h | Reserved |
Channel Logic Interrupt REQuest is shown in Table 7-63.
Return to the Summary Table.
Logic Interrupt
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | CLIREQ7 | RC | 0h | Channel Logic Interrupt Request 7
Value dependent on channel mode:
iolink_phy_mode : ECS_ERR - Establish Communication Sequence Error
uart_mode : TX_ERR - Transmission Error
fh_mode : TRX_ERR - Transmit (Transmission) or Receive Error (Parity, Frame)
ext_fh_mode: TX_ERR - Transmission Error
|
| 6 | CLIREQ6 | RC | 0h | Channel Logic Interrupt Request 6
Value dependent on channel mode:
iolink_phy_mode : WPG_ERR - Wake Pulse Generation Error
uart_mode : RX_ERR - Reception Error (Parity or Frame)
fh_mode : T1_TA_T2_TO_ERR - t1, tA or t2 Timeout Error
ext_fh_mode: RX_ERR - Reception Error (Parity or Frame Error)
|
| 5 | CLIREQ5 | RC | 0h | Channel Logic Interrupt Request 5
Value dependent on channel mode:
iolink_phy_mode : RPD_ERR - Ready Pulse Detection Error
uart_mode : OR_ERR - Over Run Error
fh_mode : CKSM_ERR - Check Sum Error (Transmit or Receive Checksum)
ext_fh_mode: N/A
|
| 4 | CLIREQ4 | RC | 0h | Channel Logic Interrupt Request 4
Value dependent on channel mode:
iolink_phy_mode : ASEQ_OK - Automated Start Sequence Completed without Errors
uart_mode : N/A
fh_mode : TBUF_EMTY_AT_CT_EXP - Tx Buffer was Empty at Cycle Timer Expiry
ext_fh_mode: N/A
|
| 3 | CLIREQ3 | RC | 0h | Channel Logic Interrupt Request 3
Value dependent on channel mode:
iolink_phy_mode : N/A
uart_mode : N/A
fh_mode : SOT - Start Of iolink message Transmission
ext_fh_mode: RX_BFULL - Rx Buffer Full
|
| 2 | CLIREQ2 | RC | 0h | Channel Logic Interrupt Request 2
Value dependent on channel mode:
iolink_phy_mode : N/A
uart_mode : N/A
fh_mode : SOR - Start of iolink message Reception
ext_fh_mode: TX_BEMPTY - Tx Buffer Empty
|
| 1 | CLIREQ1 | RC | 0h | Channel Logic Interrupt Request 1
Value dependent on channel mode:
iolink_phy_mode : CQ_R - CQ Rose
uart_mode : TX_RDY - Transmitter Ready
fh_mode : BLVL_RT - Buffer Level Reached Trigger level (Both TX and RX)
ext_fh_mode: RX_BLVL_RATL - Rx Buffer Level Rose Above Trigger Level
|
| 0 | CLIREQ0 | RC | 0h | Channel Logic Interrupt Request 0
Value dependent on channel mode:
iolink_phy_mode : CQ_F - CQ Fell
uart_mode : RX_RDY - Receiver Ready (Received byte available for read)
fh_mode : MSG_RDY - Message Ready (IO-Link Message received without errors)
ext_fh_mode: TX_BLVL_FBTL - Tx Buffer Level Fell Below Trigger Level
|
Channel Physical Interrupt REQuest is shown in Table 7-64.
Return to the Summary Table.
Physical Interrupt
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7 | OT_FAULT | RC | 0h | Over temperature fault
Latched (read-to-clear) value of over temperature fault
|
| 6 | OT_WARN | RC | 0h | Over temperature warning
Latched (read-to-clear) value of over temperature warning
|
| 5 | EXT_CQ_OC | RC | 0h | External CQ overcurrent
Latched (read-to-clear) value of external CQ overcurrent
|
| 4 | CQ_OC | RC | 0h | CQ overcurrent
Latched (read-to-clear) value of CQ overcurrent
|
| 3 | LP_OC | RC | 0h | L+ overcurrent
Latched (read-to-clear) value of L+ overcurrent
|
| 2 | LP_UVLO | RC | 0h | L+ undervoltage lockout
Latched (read-to-clear) value of L+ undervoltage lockout
|
| 1 | DI_R | RC | 0h | DI rose
Latched (read-to-clear) DI rising edge detected
|
| 0 | DI_F | RC | 0h | DI fell
Latched (read-to-clear) DI falling edge detected
|
LED Config 1 is shown in Table 7-65.
Return to the Summary Table.
LED Config / Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | BLINK | R/W | 0h | LED Blinking Configuration
Sets the blinking pattern for LED1.
|
| 5-4 | IDRV | R/W | 0h | LED Driver Current Config
Sets the current source for LED1.
|
| 3-0 | PWM | R/W | 0h | PWM duty cycle configuration
Sets the PWM duty cycle for LED1.
|
LED Config 2 is shown in Table 7-66.
Return to the Summary Table.
LED Config / Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | BLINK | R/W | 0h | LED Blinking Configuration
Sets the blinking pattern for LED2.
|
| 5-4 | IDRV | R/W | 0h | LED Driver Current Config
Sets the current source for LED2.
|
| 3-0 | PWM | R/W | 0h | PWM duty cycle configuration
Sets the PWM duty cycle for LED2.
|
LED Config 3 is shown in Table 7-67.
Return to the Summary Table.
LED Config / Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | BLINK | R/W | 0h | LED Blinking Configuration
Sets the blinking pattern for LED3.
|
| 5-4 | IDRV | R/W | 0h | LED Driver Current Config
Sets the current source for LED3.
|
| 3-0 | PWM | R/W | 0h | PWM duty cycle configuration
Sets the PWM duty cycle for LED3.
|
LED Config 4 is shown in Table 7-68.
Return to the Summary Table.
LED Config / Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | BLINK | R/W | 0h | LED Blinking Configuration
Sets the blinking pattern for LED4.
|
| 5-4 | IDRV | R/W | 0h | LED Driver Current Config
Sets the current source for LED4.
|
| 3-0 | PWM | R/W | 0h | PWM duty cycle configuration
Sets the PWM duty cycle for LED4.
|
LED Config 5 is shown in Table 7-69.
Return to the Summary Table.
LED Config / Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | BLINK | R/W | 0h | LED Blinking Configuration
Sets the blinking pattern for LED5.
|
| 5-4 | IDRV | R/W | 0h | LED Driver Current Config
Sets the current source for LED5.
|
| 3-0 | PWM | R/W | 0h | PWM duty cycle configuration
Sets the PWM duty cycle for LED5.
|
LED Config 6 is shown in Table 7-70.
Return to the Summary Table.
LED Config / Control
| Bit | Field | Type | Reset | Description |
|---|---|---|---|---|
| 7-6 | BLINK | R/W | 0h | LED Blinking Configuration
Sets the blinking pattern for LED6.
|
| 5-4 | IDRV | R/W | 0h | LED Driver Current Config
Sets the current source for LED6.
|
| 3-0 | PWM | R/W | 0h | PWM duty cycle configuration
Sets the PWM duty cycle for LED6.
|