SPRUJ66B February   2023  – September 2025

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   Applications
  6.   6
  7. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specification
      1. 1.3.1 Key Features
        1. 1.3.1.1 Processor
        2. 1.3.1.2 Memory
        3. 1.3.1.3 JTAG Emulator
        4. 1.3.1.4 Supported Interfaces and Peripherals
        5. 1.3.1.5 Expansion Connectors Headers to Support Application Specific Add On Boards
    4. 1.4 Device Information
  8. 2Hardware
    1. 2.1 EVM Revisions and Assembly Variants
    2. 2.2 System Description
      1. 2.2.1 Board Image With Markings
      2. 2.2.2 Functional Block Diagram
      3. 2.2.3 AM62A Low Power SK EVM Interface Mapping
      4. 2.2.4 Power ON/OFF Procedures
        1. 2.2.4.1 Power-On Procedure
        2. 2.2.4.2 Power-Off Procedure
        3. 2.2.4.3 Power Test Points
      5. 2.2.5 Peripheral and Major Component Description
        1. 2.2.5.1  Clocking
          1. 2.2.5.1.1 Peripheral Ref Clock
        2. 2.2.5.2  Reset
        3. 2.2.5.3  CSI Interface
        4. 2.2.5.4  Audio Codec Interface
        5. 2.2.5.5  HDMI Display Interface
        6. 2.2.5.6  JTAG Interface
        7. 2.2.5.7  Test Automation Header
        8. 2.2.5.8  UART Interface
        9. 2.2.5.9  USB Interface
          1. 2.2.5.9.1 USB 2 0 Type A Interface
          2. 2.2.5.9.2 USB 2 0 Type C Interface
        10. 2.2.5.10 Memory Interfaces
          1. 2.2.5.10.1 LPDDR4 Interface
          2. 2.2.5.10.2 Octal Serial Peripheral Interface (OSPI)
          3. 2.2.5.10.3 MMC Interfaces
            1. 2.2.5.10.3.1 MMC0 - eMMC Interface
            2. 2.2.5.10.3.2 MMC1 - Micro SD Interface
            3. 2.2.5.10.3.3 MMC2 - M.2 Key E Interface
          4. 2.2.5.10.4 Board ID EEPROM
        11. 2.2.5.11 Ethernet Interface
          1. 2.2.5.11.1 CPSW Ethernet PHY Default Configuration
        12. 2.2.5.12 GPIO Port Expander
        13. 2.2.5.13 GPIO Mapping
        14. 2.2.5.14 Power
          1. 2.2.5.14.1 Power Requirements
          2. 2.2.5.14.2 Power Input
          3. 2.2.5.14.3 Power Supply
          4. 2.2.5.14.4 AM62A SoC Power
          5. 2.2.5.14.5 Current Monitoring
        15. 2.2.5.15 AM62A Low Power SK EVM User Setup and Configuration
          1. 2.2.5.15.1 Boot Modes
          2. 2.2.5.15.2 User Test LEDs
        16. 2.2.5.16 Expansion Headers
          1. 2.2.5.16.1 User Expansion Connector
          2. 2.2.5.16.2 MCU Connector
        17. 2.2.5.17 I2C Address Mapping
  9. 3Hardware Design Files
    1. 3.1 Schematics, PCB Layout and BOM
  10. 4Additional Information
    1. 4.1 Known Hardware or Software Issues
    2. 4.2 EMC, EMI, and ESD Compliance
    3. 4.3 Trademarks
    4.     72
  11. 5Revision History

2.2.3 AM62A Low Power SK EVM Interface Mapping

Table 2-2 Interface Mapping
Interface Name Port on SoC DevicePart Number
Memory – LPDDR4 DDR0 MT53E2G32D4DE-046 AAT:A
Memory –OSPI OSPI0 W35N01JWTBAG
Memory –Micro SD Socket MMC1 MEM2051-00-195-00-A
Memory –eMMC MMC0 MTFC16GAPALBH-IT
Memory –Board ID EEPROM SoC_I2C0 AT24C512C-MAHM-T
Ethernet 1– RGMII SoC_RGMII1 DP83867IRRGZ
Ethernet 2– RGMII SoC_RGMII2 DP83867IRRGZ
GPIO Port Expander1 SoC_I2C1 TCA6424ARGJR
User Expansion Connector – 2x20 HDR SPI0,SPI2, UART5, SoC_I2C0, SoC_I2C2, McASP1 and GPIOs PEC20DAAN
MCU Header – 2x14 HDR MCU MCU_UART0, MCU_MCAN0, MCU_SPI0, MCU_I2C0 and MCU GPIOs PREC014DAAN-RC
USB– 2.0 Type C USB0 2012670005
USB– 2.0 Type A USB1 629104151021
CSI Interface CSI0 54548-2271
QSH-020-01-L-D-DP-A-K
HDMI VOUT0, McASP1and SoC_I2C1 SiI9022ACNU+ TPD12S016PWR + 10029449-001RLF
Audio Codec McASP1and SoC_I2C1 TLV320AIC3106IRGZT+ SJ-43514-SM
GPIO Port Expander2 SoC_I2C1 TCA6424ARGJR
UART Terminal (UART-to-USB) SoC_UAR SoC_UART[1:0], WKUP_UART0 and MCU_UART0 FT4232HL + 629105150521
Test Automation Header SoC_I2C1 FH12A-40S-0.5SH
Temperature Sensors SoC_I2C1 TMP100NA/3K
Current Monitors SoC_I2C1 INA231AIYFDR
Connectivity– M.2 Key E MMC2,McASP1 and SoC_UART1 2199119-4