Home Energiemanagement DC/DC switching regulators DC/DC controllers
Home
Energiemanagement
DC/DC switching regulators
DC/DC controllers
NEU

LM51261A-Q1

AKTIV

Einphasiger Aufwärtsregler für 42 V VIN, 2,2 MHz mit VOUT-Tracking und I2C für Automobilindustrie

Jetzt bestellen
Datenblatt

LM51261A-Q1

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Rating Automotive Topology Boost Controller Vin (max) (V) 45 Vin (min) (V) 2.5 Vout (max) (V) 60 Vout (min) (V) 6 Control mode current mode control Features Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Analog current monitor, Automatic Light Load Management, Automotive load dump, Bypass Mode, Chip-enable control pin, Cycle-by-cycle overcurrent protection, External Sync, Fixed PWM Mode, I2C interface, Overcurrent protection with adjustable delay, Power good, Programmable dead time, Spread Spectrum, Tracking EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 99.2 Iq (typ) (A) 0.00025 TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 150
Rating Automotive Topology Boost Controller Vin (max) (V) 45 Vin (min) (V) 2.5 Vout (max) (V) 60 Vout (min) (V) 6 Control mode current mode control Features Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Analog current monitor, Automatic Light Load Management, Automotive load dump, Bypass Mode, Chip-enable control pin, Cycle-by-cycle overcurrent protection, External Sync, Fixed PWM Mode, I2C interface, Overcurrent protection with adjustable delay, Power good, Programmable dead time, Spread Spectrum, Tracking EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 99.2 Iq (typ) (A) 0.00025 TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 150
VQFN (RHB) 32 25 mm² 5 x 5
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: TA = –40°C to +125°C
  • Functional Safety-Capable
  • Input voltage 4.5V to 42V
    • Minimum 2.5V for V(BIAS) ≥4.5V or VOUT ≥6V
  • Output voltage 6V to 60V
    • Adjustable by resistor or by I2C in 1V steps
    • Adjustable slew rate when programmed by I2C
    • 2% accuracy, internal feedback resistors
    • Bypass operation for VI > VOUT
    • Dynamic output voltage tracking
      • Digital PWM tracking (DTRK)
      • Analog tracking (ATRK)
    • Overvoltage protection (64V, 50V, 35V, 28.5V)
  • Low shutdown IQ of 2µA
  • Low operating IQ of 1mA
  • 3-phase operation with LM51251A-Q1
  • Switching frequency from 100kHz to 2.2MHz
    • Synchronization to external clock (SYNCIN)
    • Dynamically selectable switching modes (FPWM, diode emulation)
    • Spread spectrum (DRSS)
  • I2C Interface with 8 selectable addresses
  • I2C programmable dead time (14ns to 200ns)
  • Current sense resistor or DCR sensing
  • Average inductor current monitor
  • Average input current limit
    • Programmable current limit
    • Selectable delay time
  • nFAULT indicator
  • Programmable VI undervoltage lockout (UVLO)
  • Lead-less QFN-32 packable with wettable flanks
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: TA = –40°C to +125°C
  • Functional Safety-Capable
  • Input voltage 4.5V to 42V
    • Minimum 2.5V for V(BIAS) ≥4.5V or VOUT ≥6V
  • Output voltage 6V to 60V
    • Adjustable by resistor or by I2C in 1V steps
    • Adjustable slew rate when programmed by I2C
    • 2% accuracy, internal feedback resistors
    • Bypass operation for VI > VOUT
    • Dynamic output voltage tracking
      • Digital PWM tracking (DTRK)
      • Analog tracking (ATRK)
    • Overvoltage protection (64V, 50V, 35V, 28.5V)
  • Low shutdown IQ of 2µA
  • Low operating IQ of 1mA
  • 3-phase operation with LM51251A-Q1
  • Switching frequency from 100kHz to 2.2MHz
    • Synchronization to external clock (SYNCIN)
    • Dynamically selectable switching modes (FPWM, diode emulation)
    • Spread spectrum (DRSS)
  • I2C Interface with 8 selectable addresses
  • I2C programmable dead time (14ns to 200ns)
  • Current sense resistor or DCR sensing
  • Average inductor current monitor
  • Average input current limit
    • Programmable current limit
    • Selectable delay time
  • nFAULT indicator
  • Programmable VI undervoltage lockout (UVLO)
  • Lead-less QFN-32 packable with wettable flanks

The LM51261A-Q1 is a synchronous boost controller with I2C interface. The device provides a regulated output voltage for lower or equal input voltage also supporting VI to VOUT bypass mode to save power. The device can be stacked in combination with LM51251A-Q1 for 3-phase operation.

Dynamically program VOUT using the analog or digital ATRK/DTRK function or I2C programming. VI is supported down to 2.5V after startup as the internal VCC supply is automatically switched from VBIAS to VOUT for VBIAS < 4.5V. The fixed switching frequency is set between 100kHz and 2.2MHz through a resistor on the RT-pin or the SYNCIN clock. The switching modes FPWM or diode emulation can be changed during operation.

The implemented protections peak current limit, average input current limit, average inductor current monitor, overvoltage and undervoltage protection, and the thermal shutdown protect the device and the application.

The LM51261A-Q1 is a synchronous boost controller with I2C interface. The device provides a regulated output voltage for lower or equal input voltage also supporting VI to VOUT bypass mode to save power. The device can be stacked in combination with LM51251A-Q1 for 3-phase operation.

Dynamically program VOUT using the analog or digital ATRK/DTRK function or I2C programming. VI is supported down to 2.5V after startup as the internal VCC supply is automatically switched from VBIAS to VOUT for VBIAS < 4.5V. The fixed switching frequency is set between 100kHz and 2.2MHz through a resistor on the RT-pin or the SYNCIN clock. The switching modes FPWM or diode emulation can be changed during operation.

The implemented protections peak current limit, average input current limit, average inductor current monitor, overvoltage and undervoltage protection, and the thermal shutdown protect the device and the application.
filter Andere DC/DC controllers suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 2
Top-Dokumentation Typ Titel Format-Optionen Datum
* Data sheet LM5126 1 A-Q1, Wide-VIN, Single-Phase, Boost Controller with VOUT Tracking and I2C datasheet PDF | HTML 26 Nov 2025
Functional safety information LM5126A-Q1 and LM51261A-Q1 Functional Safety FIT Rate, FMD and Pin FMA PDF | HTML 24 Okt 2025

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

LM5126AEVM-BST — LM5126A – Evaluierungsmodul

Das LM5126AEVM-BST Evaluierungsmodul demonstriert die Merkmale und die Leistung des synchronen Aufwärtsreglers LM5126A-Q1 mit großem Eingangsspannungsbereich. Dieses EVM ist einfach zu konfigurieren. Das Modul ermöglicht es dem Benutzer, verschiedene Bedingungen zu testen. Die (...)
Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
Designtool

LM51261A-GUI — GUI for LM51261A

GUI for LM51261A
Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware
Start Download-Optionen
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
VQFN (RHB) 32 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos