TUSB8041
- Four Port USB 3.0 Hub
- USB 2.0 Hub Features
- Multi Transaction Translator (MTT) Hub: Four Transaction Translators
- Four Asynchronous Endpoint Buffers Per Transaction Translator
- Supports Battery Charging
- CDP Mode (Upstream Port Connected)
- DCP Mode (Upstream Port Unconnected)
- DCP Mode Complies with Chinese Telecommunications Industry Standard YD/T 1591-2009
- D+/D- Divider Mode
- Supports Operation as a USB 3.0 or USB 2.0 Compound Device
- Per Port or Ganged Power Switching and Over-Current Notification Inputs
- OTP ROM, Serial EEPROM or I2C/SMBus Slave Interface for Custom Configurations:
- VID and PID
- Port Customizations
- Manufacturer and Product Strings (not by OTP ROM)
- Serial Number (not by OTP ROM)
- Application Feature Selection Using Pin Selection or EEPROM/ or I2C/SMBus Slave Interface
- Provides 128-Bit Universally Unique Identifier (UUID)
- Supports On-Board and In-System OTP/EEPROM Programming Via the USB 2.0 Upstream Port
- Single Clock Input, 24-MHz Crystal or Oscillator
- No Special Driver Requirements; Works Seamlessly on any Operating System with USB Stack Support
- 64-Pin QFN Package (RGC)
The TUSB8041 is a four-port USB 3.0 hub. It provides simultaneous SuperSpeed USB and high-speed/full-speed connections on the upstream port and provides SuperSpeed USB, high-speed, full-speed, or low-speed connections on the downstream ports. When the upstream port is connected to an electrical environment that only supports high-speed or full-speed/low-speed connections, SuperSpeed USB connectivity is disabled on the downstream ports. When the upstream port is connected to an electrical environment that only supports full-speed/low-speed connections, SuperSpeed USB and high-speed connectivity are disabled on the downstream ports.
The TUSB8041 supports per port or ganged power switching and over-current protection, and supports battery charging applications.
An individually port power controlled hub switches power on or off to each downstream port as requested by the USB host. Also when an individually port power controlled hub senses an over-current event, only power to the affected downstream port will be switched off.
A ganged hub switches on power to all its downstream ports when power is required to be on for any port. The power to the downstream ports is not switched off unless all ports are in a state that allows power to be removed. Also when a ganged hub senses an over-current event, power to all downstream ports will be switched off.
The TUSB8041 downstream ports provide support for battery charging applications by providing Battery Charging Downstream Port (CDP) handshaking support. It also supports a Dedicated Charging Port (DCP) mode when the upstream port is not connected. The DCP mode supports USB devices which support with the USB Battery Charging and Chinese Telecommunications Industry Standard YD/T 1591-2009. In addition, an automatic mode provides transparent support for BC devices and devices supporting Divider Mode charging solutions when the upstream port unconnected.
The TUSB8041 provides pin strap configuration for some features including battery charging support, and also provides customization though OTP ROM, I2C EEPROM or via an I2C/SMBus slave interface for PID, VID, and custom port and phy configurations. Custom string support is also available when using an I2C EEPROM or the I2C/SMBus slave interface.
The device is available in a 64-pin RGC package and is offered in a commercial version (TUSB8041) for operation over the temperature range of 0°C to 70°C, and in an industrial version (TUSB8041I) for operation over the temperature range of -40°C to 85°C.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TUSB8041 Four-Port USB 3.0 Hub datasheet (Rev. E) | PDF | HTML | 2017/06/23 |
| Application note | ESD and Surge Protection for USB Interfaces (Rev. B) | PDF | HTML | 2024/01/11 | |
| Application note | TI USB Hubs: Adjusting USB_R1 | 2018/08/14 | ||
| Application note | High-Speed Layout Guidelines for Signal Conditioners and USB Hubs | 2018/06/14 | ||
| Application note | Transition From USB 3.0 Hub to USB 3.1 Hub | 2017/12/06 | ||
| Technical article | DisplayPort(TM) over USB Type-C(TM): One connector to rule them all | PDF | HTML | 2015/05/18 | |
| User guide | TUSB8041RGC REVD Evaluation Module User's Guide | 2014/05/16 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TUSB8041EVM — 4포트 USB 3.0 SuperSpeed 허브 평가 모듈
The TUSB8041EVM is a functional board design of a single device that implements both a USB 3.0 hub and a USB 2.0 hub. The evaluation module (EVM) can support both SuperSpeed (SS) and USB 2.0 (HS, FS, and LS) operation on its USB ports. This EVM is intended for use in evaluating system (...)
USB-CTM-MINIDK-EVM — 비디오 및 충전을 지원하는 USB Type-C™ 미니 도크 보드 평가 모듈
USB Type-C™ 및 PD(Power Delivery) 미니 도크 EVM(평가 모듈)은 오디오, USB 데이터, 전력 및 비디오를 포함한 USB Type-C 도크를 위한 완전한 레퍼런스 솔루션을 제공합니다. EVM에는 소형 2인치 x 4인치 폼 팩터가 있으며 기본 USB Type-C PD 포트를 통해 소스 및 싱크 전원 기능을 모두 지원합니다. 비디오 출력 기능에는 DisplayPort 및 HDMI가 모두 포함됩니다.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 착수하기 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
TIDEP0076 — DLP® 구조적 조명을 사용한 AM572x 프로세서 기반의 3D 머신 비전 레퍼런스 디자인
TIDA-01243 — 비디오 및 충전 지원 USB Type-C™ 및 전원 공급 미니 도크 레퍼런스 디자인
TIDEP0065 — PRU-ICSS를 사용한 향상된 I2C 및 SMBus 마스터 인터페이스 레퍼런스 디자인
TIDEP0046 — DSP 가속화용 OpenCL을 사용한 AM57x의 몬테카를로 시뮬레이션 레퍼런스 디자인
TIDEP0047 — TI의 AM57x 프로세서를 사용한 전력 및 열 설계 고려 사항 레퍼런스 설계
TIDA-00288 — 4포트 USB 3.0 허브 레퍼런스 디자인
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VQFN (RGC) | 64 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.