首頁 電源管理 電源保護開關與控制器 eFuse（整合式熱插拔）
首頁
電源管理
電源保護開關與控制器
eFuse（整合式熱插拔）

TPS25990

現行

具備數位遙測控制器的 2.9-V 至 16-V、0.79-mΩ、60-A eFuse

立即訂購
產品規格表

TPS25990

現行
產品規格表 立即訂購

產品詳細資料

Vabsmax_cont (V) 20 Vin (max) (V) 16 Vin (min) (V) 2.9 Current limit (max) (A) 50 Current limit (min) (A) 7 Features Adjustable soft start, Current monitoring, Fault output, Overcurrent protection, Overvoltage protection, PMBus, Power good signal, Quick output discharge, Short-circuit protection, Stackable, Thermal shutdown, adjustable UVLO Overcurrent response Circuit breaker Fault response Auto-retry, Latch-off Ron (typ) (mΩ) 0.79 Overvoltage response Cut-off Rating Catalog Soft start Adjustable Quiescent current (Iq) (typ) (A) 0.0037 Quiescent current (Iq) (max) (A) 0.0055 Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125
Vabsmax_cont (V) 20 Vin (max) (V) 16 Vin (min) (V) 2.9 Current limit (max) (A) 50 Current limit (min) (A) 7 Features Adjustable soft start, Current monitoring, Fault output, Overcurrent protection, Overvoltage protection, PMBus, Power good signal, Quick output discharge, Short-circuit protection, Stackable, Thermal shutdown, adjustable UVLO Overcurrent response Circuit breaker Fault response Auto-retry, Latch-off Ron (typ) (mΩ) 0.79 Overvoltage response Cut-off Rating Catalog Soft start Adjustable Quiescent current (Iq) (typ) (A) 0.0037 Quiescent current (Iq) (max) (A) 0.0055 Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125
VQFN-HR (RQP) 26 22.5 mm² 5 x 4.5
  • Input operating voltage range: 2.9 V to 16 V
    • 20-V absolute maximum at input
    • Withstands up to –1 V at output
  • Integrated low on-resistance FET: 0.79 mΩ (typ.)
    • Rated for 50 A RMS and 60 A peak current
  • Can be used as a standalone eFuse or primary controller in parallel configuration
    • Supports parallel connection of multiple eFuses for higher current support
    • Active device state synchronization and load sharing during start-up and steady-state for unlimited scalability

  • PMBus® interface for telemetry, control, configuration and debug

    • P IN/E IN/V IN/V OUT/I IN/temperature/fault monitoring
    • Power cycle with a single command
    • On-chip non-volatile configuration memory
    • Blackbox fault recording of multiple events with relative time-stamp and option to store on an external EEPROM
  • Robust overcurrent protection
    • Programmable overcurrent threshold (I OCP): 7 A to 50 A with accuracy of ±5% (max.)
    • Circuit-breaker response during steady-state with a programmable transient blanking timer (OC_TIMER) to support peak load currents
    • Active current limit during start-up (I LIM)
  • Robust short-circuit protection
    • Fast-trip response (280 ns)
    • Programmable and fixed thresholds
    • Immune to supply line transients — no nuisance tripping
  • Programmable overtemperature protection (OTP)

    • Assured FET SOA: 8 W√s

  • Integrated FET health monitoring and reporting
  • Precise analog load current monitoring (IMON)
    • ±2% accuracy
    • > 500-kHz analog bandwidth
  • Fast overvoltage protection with programmable

    threshold

  • Programmable output slew rate control (dVdt)
  • Programmable insertion delay timer
  • Programmable undervoltage lockout (UVLO)
  • Analog die temperature monitor output (TEMP)
  • Four configurable general purpose I/O pins
  • Small footprint : QFN 4.5-mm × 5-mm, 0.6-mm pitch
    • 29-mil clearance between power and GND pins
  • 100% Pb Free
  • Input operating voltage range: 2.9 V to 16 V
    • 20-V absolute maximum at input
    • Withstands up to –1 V at output
  • Integrated low on-resistance FET: 0.79 mΩ (typ.)
    • Rated for 50 A RMS and 60 A peak current
  • Can be used as a standalone eFuse or primary controller in parallel configuration
    • Supports parallel connection of multiple eFuses for higher current support
    • Active device state synchronization and load sharing during start-up and steady-state for unlimited scalability

  • PMBus® interface for telemetry, control, configuration and debug

    • P IN/E IN/V IN/V OUT/I IN/temperature/fault monitoring
    • Power cycle with a single command
    • On-chip non-volatile configuration memory
    • Blackbox fault recording of multiple events with relative time-stamp and option to store on an external EEPROM
  • Robust overcurrent protection
    • Programmable overcurrent threshold (I OCP): 7 A to 50 A with accuracy of ±5% (max.)
    • Circuit-breaker response during steady-state with a programmable transient blanking timer (OC_TIMER) to support peak load currents
    • Active current limit during start-up (I LIM)
  • Robust short-circuit protection
    • Fast-trip response (280 ns)
    • Programmable and fixed thresholds
    • Immune to supply line transients — no nuisance tripping
  • Programmable overtemperature protection (OTP)

    • Assured FET SOA: 8 W√s

  • Integrated FET health monitoring and reporting
  • Precise analog load current monitoring (IMON)
    • ±2% accuracy
    • > 500-kHz analog bandwidth
  • Fast overvoltage protection with programmable

    threshold

  • Programmable output slew rate control (dVdt)
  • Programmable insertion delay timer
  • Programmable undervoltage lockout (UVLO)
  • Analog die temperature monitor output (TEMP)
  • Four configurable general purpose I/O pins
  • Small footprint : QFN 4.5-mm × 5-mm, 0.6-mm pitch
    • 29-mil clearance between power and GND pins
  • 100% Pb Free

The TPS25990 is an integrated, high-current circuit protection and power management device in a small package. The device provides multiple protection modes using very few external components and is a robust defense against overloads, short circuits, and excessive inrush current.

The integrated PMBus® interface allows a host controller to monitor, control and configure the system in real-time. Key system parameters can be read back by remote telemetry. Various protection, warning thresholds and coefficients can be configured through PMBus® or stored in non-volatile configuration memory. Blackbox fault recording feature helps in the debugging of field failures and returns.

The device can be used as a standalone eFuse, or connected as a primary controller in a parallel eFuse configuration for higher current support. All devices actively synchronize their operating state and share current during start-up and steady state to avoid over-stressing some of the devices which can result in premature or partial shutdown of the parallel chain.

An integrated fast and accurate sense analog load current monitor facilitates predictive maintenance and advanced dynamic platform power management techniques such as Intel PSYS and PROCHOT to maximize system throughput and power supply usage. This in conjunction with an integrated digital oscilloscope function and Blackbox, helps with predictive maintenance in critical systems.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.

The TPS25990 is an integrated, high-current circuit protection and power management device in a small package. The device provides multiple protection modes using very few external components and is a robust defense against overloads, short circuits, and excessive inrush current.

The integrated PMBus® interface allows a host controller to monitor, control and configure the system in real-time. Key system parameters can be read back by remote telemetry. Various protection, warning thresholds and coefficients can be configured through PMBus® or stored in non-volatile configuration memory. Blackbox fault recording feature helps in the debugging of field failures and returns.

The device can be used as a standalone eFuse, or connected as a primary controller in a parallel eFuse configuration for higher current support. All devices actively synchronize their operating state and share current during start-up and steady state to avoid over-stressing some of the devices which can result in premature or partial shutdown of the parallel chain.

An integrated fast and accurate sense analog load current monitor facilitates predictive maintenance and advanced dynamic platform power management techniques such as Intel PSYS and PROCHOT to maximize system throughput and power supply usage. This in conjunction with an integrated digital oscilloscope function and Blackbox, helps with predictive maintenance in critical systems.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.
filter 尋找其它 eFuse（整合式熱插拔）
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
TPS25985 現行 具有精確和快速電流監視器的 4.5-V 至 16-V、0.59-mΩ、80-A 堆疊式精巧 eFuse Without PMBUS

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 5
類型 標題 日期
* Data sheet TPS25990 2.9 V – 16 V, 0.79-mΩ, 60-A Stackable eFuse with PMBus Digital Telemetry datasheet (Rev. B) PDF | HTML 2023年 6月 5日
Application note Enhancing Server Power Design Using Advanced Features of TI’s Smart eFuses PDF | HTML 2025年 1月 29日
Application note Implementation of PSYS Monitor Using TPS25984, TPS25985, or TPS25990 eFuses PDF | HTML 2023年 11月 15日
Certificate TPS25990EVM EU RoHS Declaration of Conformity (DoC) (Rev. A) 2023年 4月 6日
Technical article How a fully-stackable eFuse can help meet ever-increasing power needs of servers PDF | HTML 2022年 10月 3日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS25990EVM — 具數位遙測和 PMBus® 的 TPS25990 評估模組，適用 2.9-V 至 16-V、60-A、0.79-mΩ eFuse

TPS25990EVM eFuse 評估板允許對 TPS25990 eFuse 進行參考電路評估。TPS25990 裝置是具整合式 0.79-mΩ FET 的 2.9-V 至 16-V、60-A eFuse。其具備過電流、突波電流管理、可調節式過電流瞬態消隱定時器、可編程欠電壓、過電壓保護數位遙測和透過 PMBus® 的可配置性。

使用指南: PDF | HTML
TI.com 無法提供
開發模組 (EVM) 的 GUI

TPS25990EVM-GUI — TPS25990 evaluation module GUI

The GUI allows the customer to configure, control, and view telemetry data from the TPS25990 eFuse.
支援產品和硬體

支援產品和硬體

產品
eFuse（整合式熱插拔）
  • TPS25990 — 具備數位遙測控制器的 2.9-V 至 16-V、0.79-mΩ、60-A eFuse
硬體開發
開發板
  • TPS25990EVM — 具數位遙測和 PMBus® 的 TPS25990 評估模組，適用 2.9-V 至 16-V、60-A、0.79-mΩ eFuse
啟動
計算工具

SLVRBL2 — TPS25990 Design Calculator

支援產品和硬體

支援產品和硬體

產品
eFuse（整合式熱插拔）
  • TPS25990 — 具備數位遙測控制器的 2.9-V 至 16-V、0.79-mΩ、60-A eFuse
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN-HR (RQP) 26 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片