SPRADJ6 November   2026 AWR1243 , AWR1443 , AWR1642 , AWR1843 , AWR2188 , AWR2243 , AWR2544 , AWR2944 , AWR2944P , AWR6443 , AWR6843 , AWRL1432 , AWRL6432 , AWRL6844 , AWRL6888 , IWR1443 , IWR1642 , IWR1843 , IWR2188 , IWR2243 , IWR2944 , IWR6243 , IWR6443 , IWR6843 , IWRL1432 , IWRL6432 , IWRL6432W , IWRL6843 , IWRL6844

 

  1.   1
  2.   Abstract
  3. 1Introduction
    1. 1.1 What is a mmWave Radar Antenna?
    2. 1.2 Features of mmWave Radar Antennas
      1. 1.2.1 Fundamental Antenna Parameters
      2. 1.2.2 Fundamental Antenna Array Parameters
    3. 1.3 Antenna Type Selection
    4. 1.4 Critical Sections of Antenna
      1. 1.4.1 Source
      2. 1.4.2 Feeding Network
      3. 1.4.3 Radiating Element
    5. 1.5 Antenna Array and Pattern Selection
      1. 1.5.1 Virtual Antenna Array
    6. 1.6 PCB Material Impact on Antenna Performance
  4. 2Antenna Design Flow
    1. 2.1 End Application Evaluation
    2. 2.2 Form Factor and Stack-up Decision
    3. 2.3 Link Budget and Antenna Feature Definition
    4. 2.4 Single Antenna Element Design
    5. 2.5 Antenna Array Design
    6. 2.6 Layout Creation and Simulation
    7. 2.7 Fabrication and Design Validation
  5. 3Summary
  6. 4References

Antenna Type Selection

Selecting an antenna involves balancing several factors: the target application, the operating frequency, the available form factor, ease of manufacture, and overall cost. The application is the starting point, because it defines what the antenna must deliver in gain, directivity, bandwidth, and FOV.

Consider a satellite communication link. It requires a highly directive antenna with high gain and a narrow FOV so that energy is focused toward a distant target. Size is a secondary concern in such systems, so physically large antennas such as Yagi-Uda, horn, and helical designs are common. These structures typically operate at lower frequencies, where their larger dimensions are practical.

mmWave applications present a different set of constraints. At these frequencies, wavelengths are only a few millimeters, and the antenna must fit within compact devices. The form factor is therefore dictated by both the application and the operating frequency. Several antenna types can be realized at this small scale, including dipoles, monopoles, and patches. The final choice depends mainly on the required radiation pattern. Dipole and monopole antennas, for example, provide omnidirectional coverage, radiating roughly equally in all directions. That is useful for general connectivity but less suited to sensing, where controlled coverage is usually needed.

Why Patch Antennas Are Preferred for mmWave Radar

Patch antennas have become the dominant choice for mmWave radar sensor boards, for several reasons.

  • Design flexibility: A patch antenna can be tuned by trading bandwidth, gain, and FOV against one another. This lets designers shape the radiation pattern to suit the sensing task, whether that is wide-angle detection or long-range, focused coverage.
  • Planar, low-profile form: The patch is a flat structure that integrates directly into a printed circuit board (PCB) alongside the radar chip and other circuitry. This eliminates the need for separate antenna assemblies and keeps the module compact.
  • Simple enclosure: Because the antenna lies flat on the board, it can be covered with a radome (a protective cover transparent to RF energy) with little effort, which protects it without degrading performance significantly.
  • Manufacturability and cost: Patch antennas are produced using standard PCB fabrication processes, so they are repeatable, scalable to high volumes, and inexpensive.

A patch antenna is built from a dielectric substrate sandwiched between two copper layers. The radiating element is formed on the top layer by etching away unwanted copper, leaving a patch of defined shape and dimensions. The bottom copper layer remains intact and serves as the reference ground plane. This design is shown in Figure 1-7

A single patch provides moderate gain with a relatively wide beam. When a radar needs longer range, multiple patches are arranged in an array. Their combined radiation increases gain and produces a more directive beam. This comes at the cost of a narrower FOV, so the array size and layout must be chosen to strike the right balance between range and coverage for the application.

 Microstrip Patch
                    Antenna Figure 1-7 Microstrip Patch Antenna