LP87524J-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
- Input Voltage: 2.8 V to 5.5 V
- Output Voltage: 0.6 V to 3.36 V
- Four High-Efficiency Step-Down DC-DC Converter Cores:
- Total Output Current Up To 10 A
- Output Voltage Slew-Rate 3.8 mV/µs
- 4-MHz Switching Frequency
- Spread-Spectrum Mode and Phase Interleaving
- Configurable General Purpose I/O (GPIOs)
- I2C-Compatible Interface which Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
- Interrupt Function with Programmable Masking
- Programmable Power Good Signal (PGOOD)
- Output Short-Circuit and Overload Protection
- Overtemperature Warning and Protection
- Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)
The LP87524B/J/P-Q1 is designed to meet the power management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC-DC converter cores, which are configured as 4 single phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.
The automatic PFM/PWM (AUTO mode) operation maximizes efficiency over a wide output-current range. The LP87524B/J/P-Q1 supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) thus improving the accuracy of the output voltage. In addition the switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.
The LP87524B/J/P-Q1 device supports load-current measurement without the addition of external current-sense resistors. In addition, the LP87524B/J/P-Q1 supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can also include GPIO signals to control external regulators, load switches and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output voltage overshoot and the in-rush current.
您可能會感興趣的類似產品
引腳對引腳且具備與所比較裝置相同的功能
功能相同,但引腳輸出與所比較的裝置不同
功能與所比較的裝置相似
技術文件
類型 | 標題 | 日期 | ||
---|---|---|---|---|
* | Data sheet | LP87524B/J/P-Q1 Four 4-MHz Buck Converters for AWR and IWR MMICs datasheet (Rev. B) | PDF | HTML | 2018年 12月 6日 |
User guide | LP87524x-Q1 Technical Reference Manual (Rev. A) | PDF | HTML | 2021年 5月 10日 | |
Application brief | The Benefits of FlexPower PMIC Devices (Rev. B) | PDF | HTML | 2020年 11月 23日 | |
Application note | Power Management Optimizations - Low Cost LC Filter Solution (Rev. A) | PDF | HTML | 2020年 11月 11日 | |
Application note | XWR1xxx Power Management Optimizations - Low Cost LC Filter Solution | 2017年 10月 16日 |
設計與開發
電源供應解決方案
探索包括 LP87524J-Q1 的解決方案。TI 提供適用於 TI 與非 TI 之系統單晶片 (SoC)、處理器、微控制器、感測器或現場可編程邏輯閘陣列 (FPGA) 的電源供應解決方案。
AWR1843AOPEVM — 適用於單晶片 76-GHz 至 81-GHz 車用雷達感測器的 AWR1843AOP 評估模組
The AWR1843 antenna-on-package (AoP) evaluation module (EVM) is an easy-to-use platform for evaluating the AWR1843AOP mmWave radar sensor, with direct connectivity to MMWAVEICBOOST and DCA1000EVM development kits (sold separately).
AWR1843AOPEVM contains everything required to start developing (...)
LP87524Q1EVM — LP87524-Q1 四路輸出單相降壓轉換器評估模組
MMWAVEICBOOST — mmWave 感測器載波卡平臺
The MMWAVEICBOOST carrier card expands capabilities of select 60 GHz mmWave evaluation modules. This board provides advanced software developement, debug features such as trace and single step via TI’s Code Composers compatible debuggers. On-board Launchpad interface enables pairing with (...)
封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
---|---|---|
VQFN-HR (RNF) | 26 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。