LP87524B-Q1

現行

適用於 AWR 和 IWR MMIC 的多相 4MHz、4A/1.8V + 2.5A/2.3V + 1.5A/3.3V + 1.5A/1.2V 降壓轉換器

產品詳細資料

Regulated outputs (#) 4 Configurability Factory programmable, Software configurable Vin (min) (V) 2.8 Vin (max) (V) 5.5 Vout (min) (V) 0.6 Vout (max) (V) 3.36 Iout (max) (A) 3 Features Diagnostics, Dynamic voltage scaling, Enable, I2C control, Overcurrent protection, Power good, Power sequencing, Spread-Spectrum Clock (SSC) Generation, Thermal shutdown, UVLO fixed Step-up DC/DC converter 0 Step-down DC/DC converter 4 Step-down DC/DC controller 0 Step-up DC/DC controller 0 LDO 0 Iq (typ) (mA) 0.0067 Rating Automotive Switching frequency (max) (kHz) 4400 Operating temperature range (°C) -40 to 125 Processor supplier Texas Instruments Processor name mmWave AWR Shutdown current (ISD) (typ) (µA) 1.4 Switching frequency (typ) (kHz) 4000 Product type Radar sensor
Regulated outputs (#) 4 Configurability Factory programmable, Software configurable Vin (min) (V) 2.8 Vin (max) (V) 5.5 Vout (min) (V) 0.6 Vout (max) (V) 3.36 Iout (max) (A) 3 Features Diagnostics, Dynamic voltage scaling, Enable, I2C control, Overcurrent protection, Power good, Power sequencing, Spread-Spectrum Clock (SSC) Generation, Thermal shutdown, UVLO fixed Step-up DC/DC converter 0 Step-down DC/DC converter 4 Step-down DC/DC controller 0 Step-up DC/DC controller 0 LDO 0 Iq (typ) (mA) 0.0067 Rating Automotive Switching frequency (max) (kHz) 4400 Operating temperature range (°C) -40 to 125 Processor supplier Texas Instruments Processor name mmWave AWR Shutdown current (ISD) (typ) (µA) 1.4 Switching frequency (typ) (kHz) 4000 Product type Radar sensor
VQFN-HR (RNF) 26 18 mm² 4.5 x 4
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 0.6 V to 3.36 V
  • Four High-Efficiency Step-Down DC-DC Converter Cores:
    • Total Output Current Up To 10 A
    • Output Voltage Slew-Rate 3.8 mV/µs
  • 4-MHz Switching Frequency
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface which Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function with Programmable Masking
  • Programmable Power Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 0.6 V to 3.36 V
  • Four High-Efficiency Step-Down DC-DC Converter Cores:
    • Total Output Current Up To 10 A
    • Output Voltage Slew-Rate 3.8 mV/µs
  • 4-MHz Switching Frequency
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface which Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function with Programmable Masking
  • Programmable Power Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)

The LP87524B/J/P-Q1 is designed to meet the power management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC-DC converter cores, which are configured as 4 single phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.

The automatic PFM/PWM (AUTO mode) operation maximizes efficiency over a wide output-current range. The LP87524B/J/P-Q1 supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) thus improving the accuracy of the output voltage. In addition the switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP87524B/J/P-Q1 device supports load-current measurement without the addition of external current-sense resistors. In addition, the LP87524B/J/P-Q1 supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can also include GPIO signals to control external regulators, load switches and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output voltage overshoot and the in-rush current.

The LP87524B/J/P-Q1 is designed to meet the power management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC-DC converter cores, which are configured as 4 single phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.

The automatic PFM/PWM (AUTO mode) operation maximizes efficiency over a wide output-current range. The LP87524B/J/P-Q1 supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) thus improving the accuracy of the output voltage. In addition the switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP87524B/J/P-Q1 device supports load-current measurement without the addition of external current-sense resistors. In addition, the LP87524B/J/P-Q1 supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can also include GPIO signals to control external regulators, load switches and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output voltage overshoot and the in-rush current.

下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
LP87524J-Q1 現行 適用於 AWR 和 IWR MMIC 的多相 4 MHz、4A/1.0V + 2.5A/1.8V + 1.5A/3.3V + 1.5A/1.2V 降壓轉換器 This product is for LDO-free radar designs.
LP87524P-Q1 現行 適用於 AWR MMIC 的車用多相 4 MHz、3A/1.0V + 3A/1.0V + 2.5A/1.8V + 1.5A/1.2V 降壓轉換器 This product is for cascaded radar designs.
功能相同,但引腳輸出與所比較的裝置不同
LP87745-Q1 現行 適用於雷達 MMIC 的汽車三路 3-A 低雜訊降壓轉換器、IO LDO 和 5-V 升壓轉換器 PMIC Much improved RF low noise performance switching at 17.6MHz with the smallest solution size and external LDO free.
功能與所比較的裝置相似
LP87702-Q1 現行 具有診斷功能的雙路降壓轉換器和 5V 升壓 Functional Safety Quality-Managed for 3.3-V input optimized radar systems. 

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件,然後再試一次。
檢視所有 6
類型 標題 日期
* Data sheet LP87524B/J/P-Q1 Four 4-MHz Buck Converters for AWR and IWR MMICs datasheet (Rev. B) PDF | HTML 2018年 12月 6日
User guide LP87524x-Q1 Technical Reference Manual (Rev. A) PDF | HTML 2021年 5月 10日
Application brief The Benefits of FlexPower PMIC Devices (Rev. B) PDF | HTML 2020年 11月 23日
Application note Power Management Optimizations - Low Cost LC Filter Solution (Rev. A) PDF | HTML 2020年 11月 11日
Technical article Let’s break it down: how buck converters make your power supply more flexible PDF | HTML 2017年 12月 13日
Application note XWR1xxx Power Management Optimizations - Low Cost LC Filter Solution 2017年 10月 16日

設計與開發

電源供應解決方案

探索包括 LP87524B-Q1 的解決方案。TI 提供適用於 TI 與非 TI 之系統單晶片 (SoC)、處理器、微控制器、感測器或現場可編程邏輯閘陣列 (FPGA) 的電源供應解決方案。

開發板

AWR1243BOOST — AWR1243 76 GHz 至 81 GHz 高效能車用 MMIC 評估模組

The AWR1243 BoosterPack™ plug-in module is an easy-to-use evaluation board for the single-chip AWR1243 mmWave sensing device.

AWR1243BOOST contains everything required to start developing using the MMWAVE-STUDIO environment and the DCA1000 real-time data capture adapter.

The standard 20-pin (...)

使用指南: PDF
TI.com 無法提供
開發板

AWR1443BOOST — AWR1443 單晶片 76 GHz 至 81 GHz 車用雷達感測器評估模組

The AWR1443 BoosterPack™ plug-in module is an easy-to-use 77GHz mmWave sensor evaluation board for the single-chip AWR1443 mmWave sensing device, with direct connectivity to the TI MCU LaunchPad™ development-kit ecosystem.

AWR1443BOOST contains everything required to start developing on a low-power (...)

使用指南: PDF
TI.com 無法提供
開發板

AWR1642BOOST — AWR1642 單晶片 76 GHz 至 81 GHz 車用雷達感測器評估模組

AWR1642BOOST is an easy-to-use 77GHz mmWave sensor evaluation board for the AWR1642 device, with direct connectivity to the microcontroller unit (MCU) LaunchPad™ development-kit ecosystem.

The BoosterPack™ plug-in module contains everything required to start developing software for on-chip (...)

使用指南: PDF
TI.com 無法提供
開發板

AWR1642BOOST-ODS — 具有寬視野 (FOV) 天線的 AWR1642 障礙物偵測感測器評估模組

AWR1642BOOST-ODS is an easy-to-use 77GHz mmWave sensor evaluation board for the AWR1642 device with integrated DSP and MCU. The evaluation board comes with a patch-antenna structure that provides wide field of view (FOV) in both azimuth and elevation planes, and is suited for automotive (...)

使用指南: PDF
TI.com 無法提供
開發板

AWR2243BOOST — AWR2243 第二代 76-GHz 至 81-GHz 高效能車用 MMIC 評估模組

The AWR2243 BoosterPack™ plug-in module is an easy-to-use evaluation board for the single-chip AWR2243 mmWave sensing device.

AWR2243BOOST contains everything required to start developing using the MMWAVE-STUDIO environment and the DCA1000 real-time data capture adapter.

The standard 20-pin (...)

使用指南: PDF | HTML
TI.com 無法提供
開發板

AWR6843AOPEVM — 具 AoP 且適用單晶片 60-GHz 至 64-GHz 車用雷達感測器的 AWR6843AOP 評估模組

AWR6843 封裝天線技術 (AoP) 評估模組 (EVM) 是一款使用方便的 60-GHz 車用 mmWave 感測器評估平台,搭載整合式、短程、寬視野 (FoV) AoP 技術,可直接連接 mmWave 感測器載波卡平台 (MMWAVEICBOOST),也可獨立使用。EVM 可透過 USB 介面存取點雲資料,以及透過 60 接腳高速連接器存取原始類比轉數位轉換器 (ADC) 資料。

AWR6843AOPEVM 可評估車內感測應用,例如車內兒童偵測和乘員監控。

此套件受標準 mmWave 工具和軟體支援,包含 mmWave studio (MMWAVE-STUDIO) 和 mmWave (...)

使用指南: PDF | HTML
TI.com 無法提供
開發板

IWR1443BOOST — 適用於單晶片 77GHz mmWave 感測器的 IWR1443 BoosterPack™ 評估模組

IWR1443 BoosterPack™ 外掛模組是一款易於使用的 77GHz mmWave 感測器評估板,適用於單晶片 IWR1443 mmWave 感測產品,且可直接連接至 TI MCU LaunchPad™ 開發套件生態系統。

IWR1443BOOST 包含著手在低功耗 Arm® Cortex® R4F 處理器上進行開發所需的一切。此評估電路板包含用於編程與偵錯的板載模擬功能,以及可快速整合簡易使用者介面的板載按鈕與 LED。

此套件受 mmWave 工具和軟體支援,包含 mmWave Studio (MMWAVE-STUDIO) 和 mmWave 軟體開發套件 (MMWAVE-SDK)。

(...)

使用指南: PDF
TI.com 無法提供
開發板

IWR1642BOOST — 適用於單晶片 77GHz mmWave 感測器的 IWR1642 BoosterPack™ 評估模組

IWR1642BOOST 是一款易於使用的 77GHz mmWave 感測器評估板,適用於 IWR1642 產品,且可直接連接至微控制器 (MCU) LaunchPad™ 開發套件。

BoosterPack™ 包含著手為晶片內建 C67x DSP 核心及低功耗 ARM® R4F 控制器開發軟體所需的一切,包括用於編程與偵錯的板載模擬功能,以及可快速整合簡易使用者介面的板載按鈕與 LED。

此套件受 mmWave 工具和軟體支援,包含 mmWave Studio (MMWAVE-STUDIO) 和 mmWave 軟體開發套件 (MMWAVE-SDK)。

標準 20 針腳 BoosterPack (...)

使用指南: PDF
TI.com 無法提供
開發板

LP87524Q1EVM — LP87524-Q1 四路輸出單相降壓轉換器評估模組

The LP87524Q1EVM demonstrates the integrated circuit LP87524-Q1 from Texas Instruments. The LP87524-Q1 is a high-performance, multiphase step-down converter designed to meet the power management requirements of the latest applications processors in automotive applications. The device contains four (...)
使用指南: PDF
TI.com 無法提供
模擬型號

LP87524B PSpice Transient Model

SNVMB85.ZIP (364 KB) - PSpice Model
模擬型號

LP87524B-Q1 SIMPLIS Transient

SNVMBG0.ZIP (274 KB) - SIMPLIS Model
參考設計

TIDEP-0092 — 短距離雷達 (SRR) 參考設計

The TIDEP-0092 reference design provides a foundation for short-range radar (SRR) applications using the AWR1642 evaluation module (EVM). This design allows the estimation and tracking of the position (in the azimuthal plane) and velocity of objects in its field of view up to 80 m,  travelling (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-01001 — 車輛乘員偵測參考設計

This reference design demonstrates the use of the AWR6843 60GHz single-chip mmWave sensor with integrated DSP, as a Vehicle Occupant Detection (VOD) and Child Presence Detection (CPD) Sensor enabling the detection of life forms in a vehicle. This design provides a reference software processing (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-01025 — mmWave 診斷和監控參考設計

此參考設計展示了 mmWave 雷達感測器中內建自動監控功能,此功能可透過降低主機上的處理負載來提高系統效率。此設計使用安全診斷資料庫 (SDL),以對可編程數位核心、周邊設備和記憶體執行診斷測試。此參考設計也會配置並啟用不同硬體元件的 RF/類比監控功能。此設計藉由協助使用者利用各種安全資源實作符合 ASIL-B/SIL2 標準的產品,可減少整體開發時間和上市時間。
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-0091 — 77 GHz 液位發送器功率最佳化參考設計

TIDEP-0091 highlights strategies for power optimization of IWR14xx 76- to 81-GHz mmWave sensors in tank level-probing applications, displacement sensors, 4- to 20-mA sensors and other low-power applications for detecting range with high accuracy in a minimal power envelope. In these (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-0090 — 使用毫米波雷達感測器的交通監測物體偵測與追蹤參考設計

This reference design demonstrates how our single-chip millimeter-wave (mmWave) technology can be used for robust, long-range sensing in traffic monitoring and other applications. The reference design can use the  IWR1642BOOST evaluation module (EVM) or the IWR1843BOOST evaluation module (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-01000 — 採用 mmWave 雷達感測器的人數計算和追蹤參考設計

This reference design demonstrates the use of IWR6843, which is a single-chip mmWave radar sensor with integrated DSP for an indoor and outdoor people counting application. This reference design uses the IWR6843ISK evaluation module (EVM) and integrates a complete radar processing chain onto the (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-01011 — 採用 77-GHz mmWave 感測器的自動停車系統參考設計

This reference design demonstrates the use of AWR1843, a 77-GHz single-chip mmWave sensor with integrated DSP, MCU, and hardware accelerator as an automated parking sensor, which enables robust detection of objects around a car in challenging parking and environmental conditions. With a range (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-0094 — 具有整合式單晶元毫米波感測器和 80 公尺範圍的物體偵測參考設計

TIDEP-0094 provides a foundation to evaluate object detection using the IWR1642 evaluation module (EVM). This reference design integrates a complete radar processing chain onto the IWR1642 device to enable the estimation of the position (in the azimuthal plane) and the velocity of (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDEP-0104 — 使用 77-GHz mmWave 感測器的障礙物偵測參考設計

This reference design demonstrates the use of the AWR1642 single-chip mmWave sensor with integrated DSP as an obstacle-detection sensor for the car door and trunk, enabling applications like automatic car door openers and intelligent car doors that can accurately detect obstacles/objects in a (...)
Design guide: PDF
電路圖: PDF
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN-HR (RNF) 26 Ultra Librarian

訂購與品質

內含資訊:
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊:
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

內容係由 TI 和社群貢獻者依「現狀」提供,且不構成 TI 規範。檢視使用條款

若有關於品質、封裝或訂購 TI 產品的問題,請參閱 TI 支援。​​​​​​​​​​​​​​

影片