SBASAE3 December   2025 ADS125H18

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1  Offset Error Measurement
    2. 6.2  Offset Drift Measurement
    3. 6.3  Gain Error Measurement
    4. 6.4  Gain Drift Measurement
    5. 6.5  NMRR Measurement
    6. 6.6  CMRR Measurement
    7. 6.7  PSRR Measurement
    8. 6.8  SNR Measurement
    9. 6.9  INL Error Measurement
    10. 6.10 THD Measurement
    11. 6.11 SFDR Measurement
    12. 6.12 Noise Performance
    13. 6.13 TUE (Total Unadjusted Error) Measurement
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Voltage Divider and Input Multiplexer
      2. 7.3.2  Input Range
      3. 7.3.3  ADC Reference Voltage
      4. 7.3.4  Power Supplies
        1. 7.3.4.1 AVDD and AVSS
        2. 7.3.4.2 IOVDD
        3. 7.3.4.3 CAPA and CAPD
        4. 7.3.4.4 Power-On Reset (POR)
      5. 7.3.5  Clock Operation
        1. 7.3.5.1 Internal Oscillator
        2. 7.3.5.2 External Clock
      6. 7.3.6  Modulator
      7. 7.3.7  Digital Filter
        1. 7.3.7.1 Digital Filter Latency
        2. 7.3.7.2 Sinc3 and Sinc4 Filters
        3. 7.3.7.3 Sinc4 + Sinc1 Cascade Filter
        4. 7.3.7.4 50/60Hz Notch Filters
      8. 7.3.8  FIFO Buffer
        1. 7.3.8.1 FIFO Buffer Read and Write
        2. 7.3.8.2 FIFO Overflow and Underflow
        3. 7.3.8.3 FIFO Depth Indicator
        4. 7.3.8.4 FIFO Enable and Flush
        5. 7.3.8.5 FIFO Thresholds
      9. 7.3.9  Channel Auto-Sequencer
        1. 7.3.9.1 Auto-Sequencer: Basic Operation
        2. 7.3.9.2 Sequencer Modes
          1. 7.3.9.2.1 Single-Shot Mode
          2. 7.3.9.2.2 Single Step Continuous Conversion Mode
          3. 7.3.9.2.3 Single Sequence Mode
          4. 7.3.9.2.4 Continuous Sequence Mode
        3. 7.3.9.3 Configuring the Auto-Sequencer
        4. 7.3.9.4 Starting and Stopping the Sequencer
        5. 7.3.9.5 Auto-Sequencer and DRDY Behavior
      10. 7.3.10 Offset and Gain Calibration
      11. 7.3.11 Digital PGA
      12. 7.3.12 General Purpose IOs (GPIOs)
        1. 7.3.12.1 DRDY Output
        2. 7.3.12.2 FAULT Output
      13. 7.3.13 Open Wire Current Source (OWCS)
      14. 7.3.14 Open Wire Detection with ADC 0-code output
      15. 7.3.15 System Monitors
        1. 7.3.15.1 Internal Short (Offset Calibration)
        2. 7.3.15.2 Internal Temperature Sensor
        3. 7.3.15.3 External Reference Voltage Readback
        4. 7.3.15.4 Power-Supply Readback
        5. 7.3.15.5 Resistor Divider Supply Readback
      16. 7.3.16 Monitor Flags, Indicators and Counters
        1. 7.3.16.1  Reset (RESETn flag)
        2. 7.3.16.2  AVDD Undervoltage Monitor (AVDD_UVn flag)
        3. 7.3.16.3  Reference Undervoltage Monitor (REV_UVn flag)
        4. 7.3.16.4  Modulator Overrange Monitor (MOD_OVR_FAULTn flag)
        5. 7.3.16.5  Register Map CRC (REG_MAP_CRC_FAULTn flag)
        6. 7.3.16.6  Memory Map CRC (MEM_INTERNAL_FAULTn flag)
        7. 7.3.16.7  FIFO Overflow (FIFO_OFn flag) and FIFO Underflow (FIFO_UFn flag)
        8. 7.3.16.8  FIFO CRC Fault (FIFO_CRC_FAULTn flag)
        9. 7.3.16.9  GPIO Readback
        10. 7.3.16.10 SPI CRC Fault (SPI_CRC_FAULTn flag)
        11. 7.3.16.11 Register Write Fault (REG_WRITE_FAULTn flag)
        12. 7.3.16.12 DRDY Indicator (DRDY bit)
        13. 7.3.16.13 Sequencer Active Indicator (SEQ_ACTIVE bit)
        14. 7.3.16.14 Sequence Step Indicator (STEP_INDICATOR[4:0])
        15. 7.3.16.15 ADC Conversion Counter (CONV_COUNT[3:0])
        16. 7.3.16.16 FIFO Depth Indicator (FIFO_DEPTH[8:0])
        17. 7.3.16.17 Completed Sequence Counter (SEQ_COUNT[3:0])
      17. 7.3.17 Test DAC (TDAC)
      18. 7.3.18 Parallel Post Filters
        1. 7.3.18.1 Configuring the Parallel Post Filters
        2. 7.3.18.2 Frequency Response of the Parallel Post Filters
        3. 7.3.18.3 Settling Times and DRDY Behavior When Using the Post Filters
        4. 7.3.18.4 Examples of Recommended Post Filter Settings
      19. 7.3.19 Chip Select Forwarding
        1. 7.3.19.1 Configuring the CS forward feature
        2. 7.3.19.2 CS Forward Timeout
        3. 7.3.19.3 CS Forward Header, Frame, and State Diagram
        4. 7.3.19.4 Disabling the CS-FWD mode
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power-Scalable Speed Modes
      2. 7.4.2 Sequencer Functional Modes
      3. 7.4.3 Idle Mode and Standby Mode
      4. 7.4.4 Power-Down Mode
      5. 7.4.5 Reset
        1. 7.4.5.1 RESET Pin
        2. 7.4.5.2 Reset by SPI Register Write
        3. 7.4.5.3 Reset by SPI Input Pattern
      6. 7.4.6 Synchronization
      7. 7.4.7 Conversion-Start Delay Time
    5. 7.5 Programming
      1. 7.5.1  Serial Interface (SPI)
      2. 7.5.2  Serial Interface Signals
        1. 7.5.2.1 Chip Select (CS)
        2. 7.5.2.2 Serial Clock (SCLK)
        3. 7.5.2.3 Serial Data Input (SDI)
        4. 7.5.2.4 Serial Data Output/Data Ready (SDO/DRDY)
        5. 7.5.2.5 Data Ready (DRDY) Pin
      3. 7.5.3  Serial Interface Communication Structure
        1. 7.5.3.1 SPI Frame
        2. 7.5.3.2 STATUS Header
        3. 7.5.3.3 SPI CRC
      4. 7.5.4  Device Commands
        1. 7.5.4.1 No-Operation
        2. 7.5.4.2 Read Conversion Data
        3. 7.5.4.3 Read Register Command
        4. 7.5.4.4 Write Register Command
        5. 7.5.4.5 Read FIFO Buffer Command
      5. 7.5.5  Continuous Read Mode
        1. 7.5.5.1 Read Conversion Data in Continuous Read Mode
        2. 7.5.5.2 Read Registers in Continuous Read Mode
        3. 7.5.5.3 Read FIFO Buffer in Continuous Read Mode
      6. 7.5.6  SPI communication after POR or Reset
      7. 7.5.7  DRDY Pin Behavior
      8. 7.5.8  Daisy-Chain Operation
      9. 7.5.9  3-Wire SPI Mode
        1. 7.5.9.1 3-Wire SPI Mode Frame Re-Align
      10. 7.5.10 Conversion Data
      11. 7.5.11 Data Ready
        1. 7.5.11.1 DRDY Pin and SDO/DRDY Pin
        2. 7.5.11.2 DRDY Bit
        3. 7.5.11.3 Clock Counting
    6. 7.6 Register Map
      1. 7.6.1 ADS125H18 Status and General Configuration Page
      2. 7.6.2 ADS125H18 Step Configuration Page
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Serial Interface Connections
      2. 8.1.2 Interfacing with Multiple Devices
      3. 8.1.3 Unused Inputs and Outputs
      4. 8.1.4 Device Initialization
    2. 8.2 Typical Applications
      1. 8.2.1 2-Terminal V/I PLC Analog Input Module
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Performance Plots - Crosstalk
      2. 8.2.2 3-Terminal V/I PLC Analog Input Module
      3. 8.2.3 2 -Terminal V/I PLC Analog Input Module With Solid State Switch
      4. 8.2.4 2-Terminal, single ended V/I PLC Analog Input Module
      5. 8.2.5 2-Terminal, I-Input PLC Analog Input Module
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Power Supplies
      2. 8.3.2 Power-Supply Sequencing
      3. 8.3.3 Power-Supply Decoupling
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Electrical Characteristics

minimum and maximum specifications apply from TA = –40°C to +125°C; typical specifications are at TA = 25°C; all specifications are at AVDD - AVSS = 5V, IOVDD = 1.8 V, VAINx = 0V, VCM = 0V, (VREFP – VREFN) = 2.5V, V20 variant, all speed modes, external clock, and reference buffer on (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
ANALOG INPUTS
Zin Input Impedance 1 1.25 MΩ
TUE Total Unadjusted Error, full range Internal VREF, FSR = ±10V TA = 25°C   0.03 0.06 % FSR
TA = -20°C to 105°C 0.03 0.12 % FSR
TA = 0°C to 125°C 0.03 0.09 % FSR
TA = -40°C to 125°C 0.03 0.13 % FSR
External VREF, FSR = ±10V TA = 25°C   0.02 0.07 % FSR
TA = -20°C to 105°C 0.02 0.09 % FSR
TA = -40°C to 125°C 0.02 0.1 % FSR
TUE Total Unadjusted Error, reduced range Internal VREF, FSR = ±5V TA = 25°C   0.03 0.07 % FSR
TA = -20°C to 105°C 0.03 .13 % FSR
TA = 0°C to 125°C 0.03 0.1 % FSR
TA = -40°C to 125°C 0.03 0.14 % FSR
External VREF, FSR = ±5V TA = 25°C   0.02 0.08 % FSR
TA = -20°C to 105°C 0.02 0.1 % FSR
TA = -40°C to 125°C 0.02 0.11 % FSR
DC PERFORMANCE
Resolution (no missing codes) 24 Bits
Noise See the Noise Performance section for details
INL Integral nonlinearity TA = -40°C to 125°C, VCM = 0V, OSR = 512, best fit Speed mode 3 or 2 7 25 ppm of FSR
Speed mode 1 or 0 3 6
Offset error TA = 25°C –8 0.5 8 mV
Offset drift 4 30 µV/°C
Gain error TA = 25°C, using external reference –850 ±200 850 ppm of FSR
TA = 25°C, including internal reference –1300 ±300 1300
Gain drift Using external reference ±2 ppm of FSR/°C
Including internal reference ±5
SYSTEM PERFORMANCE
fDATA Output data rate, sinc3 or sinc4 filter Speed mode 3 (fMOD = 12.8 MHz) 0.08 1067 kSPS
Speed mode 2 (fMOD = 6.4 MHz) 0.04 533.3
Speed mode 1 (fMOD = 1.6 MHz) 0.01 133.3
Speed mode 0 (fMOD = 0.8 MHz) 0.005 66.7
NMRR Normal-mode rejection ratio, simultaneous 50/60Hz notch filter enabled fIN = 50 Hz or 60 Hz (±1 Hz), fDATA = 20 SPS,
external fCLK = 25.6 MHz
–95.3 dB
fIN = 50 Hz or 60 Hz (±1 Hz), fDATA = 20 SPS,
internal fCLK = 25.6 MHz
–82.7
fIN = 50 Hz or 60 Hz (±1 Hz), fDATA = 25 SPS,
external fCLK = 25.6 MHz
–62.7
fIN = 50 Hz or 60 Hz (±1 Hz), fDATA = 25 SPS,
internal fCLK = 25.6 MHz
–57.9
CMRR Common-mode rejection ratio At dc 86 dB
fCM = 50Hz or 60Hz (±1Hz), fDATA = 20SPS or
25SPS
125
fCM = 50Hz or 60Hz (±1Hz), fDATA > 25SPS 90
PSRR Power-supply rejection ratio AVDD at dc 77 dB
IOVDD at dc 105
VOLTAGE REFERENCE INPUTS
REFP and REFN input current (REFN = AVSS) REFP buffer off Speed mode 3 190 µA/V
Speed mode 2 130
Speed mode 1 80
Speed mode 0 70
REFP input current REFP buffer on Speed mode 3 ±0.5 µA
Speed mode 2 ±0.3
Speed mode 1 ±0.1
Speed mode 0 ±0.1
REFP and REFN
input current drift
REFP buffer off Speed mode 3 2.5 nA/℃
Speed mode 2 5
Speed mode 1 7
Speed mode 0 7.5
REFP input current drift REFP buffer on Speed mode 3 4 nA/℃
Speed mode 2 2.5
Speed mode 1 0.5
Speed mode 0 0.5
INTERNAL VOLTAGE REFERENCE
Output voltage AVDD > 4.5V,
REFOUT with respect to AVSS
REF_VAL = 0b 2.5 V
REF_VAL = 1b 4.096
2.85V ≤ AVDD ≤ 4.5V,
REFOUT with respect to AVSS
2.5
Initial accuracy TA = 25°C –0.1 ±0.02 0.1 %
Temperature drift (1) TA = 0°C to +125°C 3.5 8.5 ppm/°C
TA = –40°C to +125°C 4 12
Reference output load current Sink or source –10 10 mA
Short-circuit current limit Sink or source 25 40
Power supply rejection ratio AVDD at DC 95 dB
Load regulation 50 ppm/mA
Voltage noise 0.1 to 10Hz, CL = 1µF VREF = 2.5V 1.0 µVRMS
VREF = 4.096V 1.7
Voltage noise density 1kHz, CL = 1µF VREF = 2.5V 200 nV/√Hz
VREF = 4.096V 300
Capacitive load 0.5 1 2 µF
Resistive load 2 kΩ
Start-up time From power-down mode, CL = 1 µF, 0.01% settling 1 1.5 ms
INTERNAL OSCILLATOR
fOSCM Frequency 25.6 MHz
Accuracy –0.75 0.07 0.75 %
TEMPERATURE SENSOR
TSOffset Output voltage TA = 25°C 120 mV
TSTC Temperature coefficient 400 µV/°C
Accuracy Speed mode 0, internal clock, OSR = 12 –3 ±0.5 3 °C
MONITORS
THREF_UV Reference undervoltage threshold (2) 0.5 0.6 V
External reference voltage readback accuracy (VREFP – VREFN) / 3 ±0.5 %
Supply voltage readback accuracy AVDD / 3 ±1 %
DVDD / 3 ±1
(CAPA – AVSS) / 3 ±1
(CAPD – DGND) / 3 ±1
(RESP – RESN) / 3 ±1
TEST DAC
Test DAC reference voltage AVDD ≥ 4.65V TDAC_RANGE = 0b 2.5 V
TDAC_RANGE = 1b 4.096 V
2.85V ≤ AVDD ≤ 4.65V 2.5 V
Resolution 5 Bits
Accuracy ±1 %
Offset error Measured by the line passing through two codes ±1 10 mV
Startup Time From rising edge of TDAC enable to DAC output voltage reaching 99% of its final value. Applies to the slowest DAC config (buffer or no buffer).  10 µs
Buffer output impedance Buffer shorted to ground with code = 11111, reference voltage = 4.096V 150 Ω
Buffer Load Current, Shorted Buffer shorted to ground with code = 11111, reference voltage = 4.096V 15 mA
DIGITAL INPUTS/OUTPUTS
VIL Logic input level, low DGND 0.3 × IOVDD V
VIH Logic input level, high 0.7 × IOVDD V
VOL Logic output level, low OUT_DRV = 0b, IOL = 2 mA 0.2 × IOVDD V
OUT_DRV = 1b, IOL = 1 mA 0.2 × IOVDD
VOH Logic output level, high OUT_DRV = 0b, IOH = –2 mA 0.8 × IOVDD V
OUT_DRV = 1b, IOH = –1 mA 0.8 × IOVDD
Input hysteresis 100 mV
Input current Excluding RESET pin –1 1 µA
RESET pin internal pullup resistor 20 kΩ
ANALOG SUPPLY CURRENT
IAVDD, IAVSS AVDD and AVSS current
(Reference buffer off, internal reference off)
Speed mode 3 10 11.5 mA
Speed mode 2 7.5 9 mA
Speed mode 1 2.2 3 mA
Speed mode 0 2 2.75 mA
Standby mode 500 1200 µA
Power-down mode 180 800 µA
AVDD and AVSS additional
current (per function)
REFP buffer Speed mode 3 1.2 mA/buffer
Speed mode 2 0.8 mA/buffer
Speed mode 1 0.3 mA/buffer
Speed mode 0 0.25 mA/buffer
Internal reference 100 200 µA
Test DAC, 2.5V or 4.096V range 700 1100 µA
Test DAC buffer 800 1100 µA
DIGITAL SUPPLY CURRENT
IIOVDD IOVDD current
 
Speed mode 3, OSR = 32 0.90 1 mA
Speed mode 2, OSR = 32 0.5 0.6
Speed mode 1, OSR = 32 0.2 0.25
Speed mode 0, OSR = 32 0.12 0.2
Standby mode, external clock 5 µA
Standby mode, internal oscillator 60
Power-down mode 10
POWER DISSIPATION
PD Power dissipation AVDD = 5V,
REFP buffer off
Speed mode 3 50 mW
Speed mode 2 36
Speed mode 1 11
Speed mode 0 10
Specified by design and characterization, not production tested.
Undervoltage monitor does always trip below the specified MIN value and does never trip above the specified MAX value.