SLVSIF4 September   2026 TPS481HS04-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 SPI Timing Requirements
    7. 5.7 Switching Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Driving Capacitive, Resistive and Inductive Loads
      2. 7.3.2 Protection Mechanisms
        1. 7.3.2.1 Overcurrent Protection
          1. 7.3.2.1.1 Inrush Period - Overcurrent Protection
          2. 7.3.2.1.2 Overcurrent Protection - Steady State Operation
          3. 7.3.2.1.3 Programmable Fuse Protection
          4. 7.3.2.1.4 Immediate Shutdown Overcurrent Protection (IOCP)
        2. 7.3.2.2 Output Disable Function (OUT_DIS)
        3. 7.3.2.3 Thermal Shutdown
        4. 7.3.2.4 Reverse Battery
      3. 7.3.3 Diagnostic Mechanisms
        1. 7.3.3.1 Integrated ADC
        2. 7.3.3.2 Analog and Digital Current Sense Output
        3. 7.3.3.3 Output Voltage Measurement
        4. 7.3.3.4 MOSFET Temperature Measurement
        5. 7.3.3.5 VBB Voltage Measurement
        6. 7.3.3.6 VOUT Short-to-Battery and Open-Load
          1. 7.3.3.6.1 Measurement With Channel Output (FET) Enabled
          2. 7.3.3.6.2 Detection With Channel Output Disabled
        7. 7.3.3.7 VOUT Short-to-Battery or FET Short Detection For Power at All Times (PAAT) Loads
      4. 7.3.4 Fault Indication (FLT / WAKE)
      5. 7.3.5 SPI Mode Operation
    4. 7.4 Device Functional Modes
      1. 7.4.1 State Diagram
      2. 7.4.2 Power Down
      3. 7.4.3 SLEEP
      4. 7.4.4 Low Power Mode (LPM)
      5. 7.4.5 CONFIG or ACTIVE Mode
      6. 7.4.6 LIMPHOME Mode
    5. 7.5 TPS481HS04-Q1 Pre-production Silicon Limitations
      1. 7.5.1 SDO Pin Tristate Discrete Workaround (Only for parallel SPI configuration not for daisy chain)
  9. 8 Register Maps
    1. 8.1 TPS481HS04-Q1 Registers
    2. 8.2 EEPROM (NVM) Overview
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Tape and Reel Information
    2. 12.2 Mechanical Data

Electrical Characteristics

VBB = 8V to 60V @ VDD = 3.0 V to 5.5 V, TJ = -40°C to 150°C (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
INPUT VOLTAGE AND CURRENT
V(VBB_UVLO) VBB undervoltage lockout

UVLO_SET = 0x1 VBB rising threshold 5.5 V
VBB falling threshold 4.5 V
UVLO_SET = 0x7 VBB rising threshold 17 V
VBB falling threshold 16 V
UVLO_SET = 0xC VBB rising threshold 27 V
VBB falling threshold 26 V
UVLO_SET = 0xF VBB rising threshold 33 V
VBB falling threshold 32 V
V(VDD_UVLOR) VDD undervoltage lockout rising 2.9 V
V(VDD_UVLOF) VDD undervoltage lockout falling 2.6 V
ISLEEP,VBB Sleep current (total device leakage including all MOSFET channels) Device in SLEEP mode, VOUT = 0V TJ = 25°C 1 µA
ISLEEP,VDD Sleep current from VDD pin VVDD [char_not_recognized] 5.5V, device in SLEEP mode, VOUT = 0V TJ = 25°C 0.3 µA
IOUT(OFF),SLEEP Output leakage current (per channel) VOUT = 0V, Channel disabled, SLEEP state TJ = 25°C 0.1 µA
IQ,VDD VDD quiescent current ACTIVE state, SCLK off VDD = 5.5V 1.65 mA
VDD = 3.0V 70 µA
IQ,VBB,ACTIVE VBB quiescent current in ACTIVE state Channel enabled, IOUTx = 0A, ADC disabled, ACTIVE state VDD = 5.5V 3.2 mA
Channel enabled, IOUTx = 0A,
ADC enabled, ACTIVE state
VDD = 5.5V 3.3 mA
VDD = 3.0V 3.3 mA
Channel enabled, IOUTx = 0A,
ADC enabled, ACTIVE state
VDD = 0V 3.3 mA
IL,CONT Continuous load current, per channel One channel enabled, TAMB = 85°C TAMB = 85°C 18.5 A
RON CHARACTERISTICS
RON_OL On-resistance, OL ON mode 8V ≤ VBB ≤ 60V, IOUTx = 200mA, OL_ON_EN_CHx = 1 TJ = 25°C 215 mΩ
RON On-resistance 8V ≤ VBB ≤ 60V, IOUTx = 2A, OL_ON_EN_CHx = 0 TJ = 25°C 4.9 mΩ
CURRENT SENSE CHARACTERISTICS
IENTRY_OL_ON IOUT current to enter OL_ON mode (OL_ON_EN_CHx = 1) IOUT current to enter OL_ON mode (OL_ON_EN_CHx = 1) 1 A
IEXIT_OL_ON IOUT current to exit OL_ON mode (OL_ON_EN_CHx = 1) IOUT current to exit OL_ON mode (OL_ON_EN_CHx = 1) 1.36 A
KSNS1 Current sense ratio
IOUTx / ISNS
OL_ON_EN_CHx = 0 11450
KSNS2 Current sense ratio
IOUTx / ISNS
OL_ON_EN_CHx = 1 267
ADC CHARACTERISTICS
KDIG1 Current sense ratio
IOUTx / ISNS for ADC
OL_ON_EN_CHx = 0 25.88
KDIG2 Current sense ratio
IOUTx / ISNS for ADC
OL_ON_EN_CHx = 1 0.6
VADC_REF ADC reference voltage 2.8 V
IADC ADC current consumption 0.5 mA
SNS CHARACTERISTICS
VBBSNS_RANGE VBB SNS voltage sensing range 8 65 V
VOUTSNS_RANGE VOUT SNS voltage sensing range 0 65 V
OVERCURRENT PROTECTION CHARACTERISTICS
IOCP_RANGE Overcurrent protection threshold, immediate shutdown mode - range 18.5 74 A
IOCP Overcurrent protection threshold, immediate shutdown mode ILIMIT_SET_CHx = 0x0 18.5 A
ILIMIT_SET_CHx = 0x1 22.2 A
ILIMIT_SET_CHx = 0x2 25.9 A
ILIMIT_SET_CHx = 0x3 29.6 A
ILIMIT_SET_CHx = 0x4 33.3 A
ILIMIT_SET_CHx = 0x5 37 A
ILIMIT_SET_CHx = 0x6 40.7 A
ILIMIT_SET_CHx = 0x7 44.4 A
ILIMIT_SET_CHx = 0x8 48.1 A
ILIMIT_SET_CHx = 0x9 51.8 A
ILIMIT_SET_CHx = 0xA 55.5 A
ILIMIT_SET_CHx = 0xB 59.2 A
ILIMIT_SET_CHx = 0xC 62.9 A
ILIMIT_SET_CHx = 0xD 66.6 A
ILIMIT_SET_CHx = 0xE 70.3 A
ILIMIT_SET_CHx = 0xF 74 A
tOCP_DETECT Immediate shutdown detection time From IOUT = IOCP to IOCP detection
ROUT = 150% of IOCP , LIN = 0nH, LOUT = 0nH
1 us
tOCP_TOFF Immediate shutdown turn off time From IOCP detection to 10% of VOUTx
ROUT = 150% of IOCP , LIN = 0nH, LOUT = 0nH
3 us
CAP CHARGING
tINRUSH_RANGE Inrush duration settings range INRUSH_DURATION_CHx range 0 100 ms
ICL_Reg Current limit regulation mode INRUSH_LIMIT_CHx = 0x0 1.75 A
INRUSH_LIMIT_CHx = 0x1 2.38 A
INRUSH_LIMIT_CHx = 0x2 2.75 A
INRUSH_LIMIT_CHx = 0x3 3.13 A
INRUSH_LIMIT_CHx = 0x4 3.50 A
INRUSH_LIMIT_CHx = 0x5 3.88 A
INRUSH_LIMIT_CHx = 0x6 4.25 A
INRUSH_LIMIT_CHx = 0x7 4.63 A
INRUSH_LIMIT_CHx = 0x8 5.00 A
INRUSH_LIMIT_CHx = 0x9 5.38 A
INRUSH_LIMIT_CHx = 0xA 6.35 A
INRUSH_LIMIT_CHx = 0xB 6.8 A
INRUSH_LIMIT_CHx = 0xC 7.25 A
INRUSH_LIMIT_CHx = 0xD 7.7 A
INRUSH_LIMIT_CHx = 0xE 8.1 A
INRUSH_LIMIT_CHx = 0xF 8.6 A
CAPACITIVE CHARGING
FAULT CHARACTERISTICS
ICHx(OL_PU) Off state open-load (OL) detection internal pull-up current Switch disabled, OL_OFF_EN_CHx = enabled OL_PULLUP_STR=00 25 µA
OL_PULLUP_STR=01 57 µA
OL_PULLUP_STR=10 121 µA
OL_PULLUP_STR=11 256 µA
ICHx(SHRT_VBB) Off state short to VBB detection pulldown current Channel disabled, off-state short_VBB diagnostics enabled 6 mA
VDS_LT_2V VDS threshold during inrush duration 2 V
VCHx(STB_OL_TH) Off state Open-load (OL) and short to battery detection voltage Channel Disabled, off-state open load or short to battery diagnostics enabled, VOUTx 2 V
TABS Thermal shutdown 188 °C
TOTW Thermal shutdown warning 135 °C
TREL Relative thermal shutdown temperature 60 °C
THYS Thermal shutdown hysteresis 25 °C
tRETRY Retry time Time from fault shutdown until switch re-enable (thermal shutdown or IOCP) RETRY_TIME bit 1 ms
10
0.15
100
tLPM_WAKE_DEGLITCH Deglitch time to signal FLT/WAKE after AUTO LPM exit 1 ms
10
20
100
TIMING CHARACTERISTICS
PWMFREQ PWM Frequency PWM_EN_CHx = 1 PWM_FREQ_CHx = 000 0.8 Hz
PWM_FREQ_CHx = 001 3.2 Hz
PWM_FREQ_CHx = 010 12.7 Hz
PWM_FREQ_CHx = 011 100 Hz
PWM_FREQ_CHx = 100 200 Hz
PWM_FREQ_CHx = 101 400 Hz
PWM_FREQ_CHx = 110 816 Hz
PWM_FREQ_CHx = 111 1650 Hz
LOW POWER MODE CHARACTERISTICS
ICHx(LWUx) IOUTx current to exit LPM,
LPM_MODE = 0
LPM_EXIT_CURR_CHx = 00 0.23 A
LPM_EXIT_CURR_CHx = 01 0.47 A
LPM_EXIT_CURR_CHx = 10 0.7 A
LPM_EXIT_CURR_CHx = 11 0.93 A
IEXIT_LPM_AUTO IOUTx current to exit LPM,
LPM_MODE = 1
LPM_EXIT_CURR_CHx = 00 1.66 A
LPM_EXIT_CURR_CHx = 01 2.77 A
LPM_EXIT_CURR_CHx = 10 3.88 A
LPM_EXIT_CURR_CHx = 11 5 A
IQ,VDD,LPM VDD quiescent current in MANUAL_LPM VDD = 5.0V, IOUTx = 0A,
LPM_MODE = 0
Channel off 10 µA
Channel ON 10
VDD = 5.0V, IOUTx = 0A,
LPM_MODE = 1
Channel off 15 µA
Channel ON 15
IQ,VBB,LPM VBB quiescent current in LPM VDD = 5.0V, IOUTx = 0A,
LPM_MODE = 0
Channel off 10 µA
Channel ON 10
VDD = 5.0V, IOUTx = 0A,
LPM_MODE = 1
Channel off 15 µA
Channel ON 15
DIGITAL INPUT PIN CHARACTERISTICS
VIH,SPI Input voltage high-level
(SCLK, SDI, CSN)
3.0V ≤ VDD ≤ 5.5V 3.0V ≤ VDD ≤ 5.5V 0.7 x VVDD V
VIL,SPI Input voltage low-level
(SCLK, SDI, CSN)
3.0V ≤ VDD ≤ 5.5V 3.0V ≤ VDD ≤ 5.5V 0.3 x VVDD V
RPD,SCLK SCLK Internal pulldown resistor 2 MΩ
IIH, SCLK Input current high-level SCLK VSCLK = 5V VSCLK = 5V 2.5 µA
IIL,SCLK Input current low-level VSCLK = 0.8V VSCLK = 0.8V 0.4 µA
RPD,SDI SDI Internal pulldown resistor 2 MΩ
IIH, SDI Input current high-level SDI VSDI = 5V 2.5 µA
IIL,SDI Input current low-level VSDI = 0.8V VSDI = 0.8V 0.4 µA
RPU,CSN CSN Internal pullup resistor 100 kΩ
VIH,DI_OUT_DISx, VIH,LHI LHI and DI/OUT_DISx input voltage high-level 1 V
VIL,DI_OUT_DISx, VIL,LHI LHI and DI/OUT_DISx input voltage low-level 1.5 V
RPD,DI_OUT_DISx, RPD,LHI LHI and DI/OUT_DISx Internal pulldown resistor 10 MΩ
DIGITAL OUTPUT PIN CHARACTERISTICS
VOH,SDO Output logic high voltage drop SDO pin current = -2mA SDO pin current = -2mA 0.2 V
VOL,SDO Output logic low voltage SDO Pin current = 2mA SDO Pin current = 2mA 0.2 V
VOL_FLT Output logic low voltage drop FLT pin current = 4mA FLT pin current = 4mA 0.4 V