GUI für Evaluierungsmodul (EVM)
DRV8313
3-Phasen-Motortreiber mit 3-A-Peak für max. 65 V und integrierten FETs
Datenblatt
DRV8313
- Triple 1/2-H Bridge Driver IC
- 3-Phase brushless DC Motors
- Solenoid and Brushed DC Motors
- High Current-Drive Capability: 2.5-A Peak
- Low MOSFET ON-Resistance
- Independent 1/2-H-Bridge Control
- Uncommitted Comparator Can Be Used for Current Limit or Other Functions
- Built-In 3.3-V 10-mA LDO Regulator
- 8-V to 60-V Operating Supply-Voltage Range
- Sleep Mode for Standby Operation
- Small Package and Footprint
- 28-Pin HTSSOP (PowerPAD Package)
- 36-Pin VQFN
All trademarks are the property of their respective owners.
The DRV8313 provides three individually controllable half-H-bridge drivers. The device is intended to drive a three-phase brushless-DC motor, although it can also be used to drive solenoids or other loads. Each output driver channel consists of N-channel power MOSFETs configured in a 1/2-H-bridge configuration. Each 1/2-H-bridge driver has a dedicated ground terminal, which allows independent external current sensing.
An uncommitted comparator is integrated into the DRV8313, which allows for the construction of current-limit circuitry or other functions.
Internal protection functions are provided for undervoltage, charge pump faults, overcurrent, short circuits, and overtemperature. Fault conditions are indicated by the nFAULT pin.
For all available packages, see the orderable addendum at the end of the data sheet.Ähnliche Produkte, die für Sie interessant sein könnten
Selbe Funktionalität wie der verglichene Baustein bei abweichender Anschlussbelegung
Technische Dokumentation
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 5 | Typ | Titel | Datum | ||
|---|---|---|---|---|
| * | Data sheet | DRV8313 2.5-A Triple 1/2-H Bridge Driver datasheet (Rev. D) | PDF | HTML | 26 Apr 2016 |
| Application note | Best Practices for Board Layout of Motor Drivers (Rev. B) | PDF | HTML | 14 Okt 2021 | |
| Application note | Delay and Dead Time in Integrated MOSFET Drivers | PDF | HTML | 23 Aug 2021 | |
| EVM User's guide | DRV8313EVM User Guide (Rev. A) | 18 Okt 2018 | ||
| Application note | Sensored 3-Phase BLDC Motor Control Using MSP430 | 20 Jul 2011 |
Design und Entwicklung
Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.
Evaluierungsplatine
DRV8313EVM — DRV8313-Evaluierungsmodul
The DRV8313EVM (evaluation module) provides a cost effective, sensorless-solution for running a 3-phase BLDC motor in trapezoidal commutation.
Benutzerhandbuch: PDF
Referenzdesigns
TIDEP0025 — Ein-Chip-Antriebslösung für industrielle Kommunikation und Motorsteuerung
This reference design implements hardware interface based on the HEIDENHAIN EnDat 2.2 standard for position or rotary encoders. The platform also allows you to implement real-time EtherCAT communications standards in a broad range of industrial automation equipment. It enables designs with a low (...)
Referenzdesigns
TIDEP0039 — Referenzdesign für Sercos-III-Slave für AM437x-Kommunikationsentwicklungsplattform
The TIDEP0039 Sercos III Slave For AM437x Communication Development Platform Reference Design combines the AM437x Sitara processor family from Texas Instruments (TI) and the Sercos III media access control (MAC) layer into a single system-on-chip (SoC) solution. Targeted for Sercos III slave (...)
Referenzdesigns
TIDEP0022 — Referenzdesign für ARM-MPU mit integrierter Schnittstelle für BiSS C Master
Implementation of BiSS C Master protocol on Industrial Communication Sub-System (PRU-ICSS). The design provides full documentation and source code for Programmable Realtime Unit (PRU).
Referenzdesigns
TIDEP0035 — ARM MPU mit integrierter HIPERFACE DSL Master-Schnittstelle – Referenzdesign
This reference design implements HIPERFACE DSL master protocol on Industrial Communication Sub-System (PRU-ICSS). The two-wire interface allows integration of position feedback wires into motor cable. It consists of AM437x PRU-ICSS firmware and TIDA-00177 transceiver reference design.
Referenzdesigns
TIDEP0050 — Referenzdesign für EnDat 2.2-System
This reference design implements EnDat 2.2 Master protocol stack and hardware interface based on HEIDENHAIN EnDat 2.2 standard for position or rotary encoders. The design is composed of EnDat 2.2 Master protocol stack, half-duplex communications using RS-485 transceivers and the line termination (...)
Referenzdesigns
TIDA-01362 — Ansteuerung eines 3-Phasen-Schrittmotors mit einem BLDC-Motortreiber – Referenzdesign
TIDA-01362 demonstrates how to drive a three phase stepper motor using the same hardware structure of a Brushless (BLDC) driver. By regulating the PWM signal schemes, the design achieves a smooth sinusoidal output current. DRV8313 device is used for the implementation of this design.
Referenzdesigns
TIDA-00827 — 2,5 A, Integrierte BLDC-Motorsteuerung mit Sensor – Referenzdesign
The TIDA-00827 is an integrated, sensored BLDC motor controller reference design suitable for low-powered, battery operated, brushless DC motor applications. An 8- to 35-V operating voltage range supports 3S to 6S LiPo battery supplies. Specific applications include camera gimbals, low power fans (...)
Referenzdesigns
TIDA-00274 — Referenzdesign für kostengünstigen 3-phasigen bürstenlosen Gleichstromantrieb für sensorlose Trapezo
This reference evaluation module, featuring DRV8313, 3-phase driver with integrated MOSFETs and MSP430G2553 MCU, provides a cost effective sensor-less solution to run of 3-phase BLDC motor in trapezoidal commutation. Reference design software comes with easy to use GUI for quick evaluation. (...)
| Gehäuse | Pins | CAD-Symbole, Footprints und 3D-Modelle |
|---|---|---|
| HTSSOP (PWP) | 28 | Ultra Librarian |
| VQFN (RHH) | 36 | Ultra Librarian |
Bestellen & Qualität
Beinhaltete Information:
- RoHS
- REACH
- Bausteinkennzeichnung
- Blei-Finish/Ball-Material
- MSL-Rating / Spitzenrückfluss
- MTBF-/FIT-Schätzungen
- Materialinhalt
- Qualifikationszusammenfassung
- Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
- Werksstandort
- Montagestandort
Support und Schulungen
TI E2E™-Foren mit technischem Support von TI-Ingenieuren
Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.
Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support.