AFE031

활성

저임피던스 라인 구동을 위한 1,500mA, 통합형, PLC(전력선 통신) 아날로그 프론트 엔드

제품 상세 정보

Number of channels 1 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 7 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 26 Iout (typ) (A) 1.5 GBW (typ) (MHz) 0.67 Slew rate (typ) (V/µs) 19 Iq per channel (typ) (mA) 49 Features Adj Current Limit, Shutdown Rating Catalog Operating temperature range (°C) -40 to 125 Rail-to-rail No Architecture FET
Number of channels 1 Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V) 7 Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V) 26 Iout (typ) (A) 1.5 GBW (typ) (MHz) 0.67 Slew rate (typ) (V/µs) 19 Iq per channel (typ) (mA) 49 Features Adj Current Limit, Shutdown Rating Catalog Operating temperature range (°C) -40 to 125 Rail-to-rail No Architecture FET
VQFN (RGZ) 48 49 mm² 7 x 7
  • Integrated powerline driver with thermal and overcurrent protection
  • Conforms to EN50065-1
  • PRIME certified
  • Large output swing: 12 VPP at 1.5 A
    (15-V supply)
  • Low power consumption:
    15 mW (receive mode)
  • Programmable Tx and Rx filters
  • Supports EN50065 CENELEC bands A, B, C, D
  • Supports FSK, S-FSK, and OFDM
  • Supports PRIME, G3, IEC 61334
  • Receive sensitivity: 20 µVRMS, typical
  • Programmable Tx and Rx gain control
  • Four-wire serial peripheral interface
  • Two integrated zero crossing detectors
  • Two-wire transceiver buffer
  • 48-Pin QFN PowerPAD™ package
  • Extended junction temperature range:
    –40°C to +125°C
  • Integrated powerline driver with thermal and overcurrent protection
  • Conforms to EN50065-1
  • PRIME certified
  • Large output swing: 12 VPP at 1.5 A
    (15-V supply)
  • Low power consumption:
    15 mW (receive mode)
  • Programmable Tx and Rx filters
  • Supports EN50065 CENELEC bands A, B, C, D
  • Supports FSK, S-FSK, and OFDM
  • Supports PRIME, G3, IEC 61334
  • Receive sensitivity: 20 µVRMS, typical
  • Programmable Tx and Rx gain control
  • Four-wire serial peripheral interface
  • Two integrated zero crossing detectors
  • Two-wire transceiver buffer
  • 48-Pin QFN PowerPAD™ package
  • Extended junction temperature range:
    –40°C to +125°C

The AFE031 is a low-cost, integrated, powerline communications (PLC) analog front-end (AFE) device that is capable of capacitive- or transformer-coupled connections to the powerline while under the control of a DSP or microcontroller. It is ideal for driving low-impedance lines that require up to 1.5 A into reactive loads. The integrated receiver is able to detect signals down to 20 µVRMS and is capable of a wide range of gain options to adapt to varying input signal conditions. This monolithic integrated circuit provides high reliability in demanding powerline communications applications.

The AFE031 transmit power amplifier operates from a single supply in the range of 7 V to 24 V. At maximum output current, a wide output swing provides a 12-VPP (IOUT = 1.5 A) capability with a nominal 15-V supply. The analog and digital signal processing circuitry operates from a single 3.3-V power supply.

The AFE031 is internally protected against overtemperature and short-circuit conditions. It also provides an adjustable current limit. An interrupt output is provided that indicates both current limit and thermal limit. There is also a shutdown pin that can be used to quickly put the device into its lowest power state. Through the four-wire serial peripheral interface, or SPI™, each functional block can be enabled or disabled to optimize power dissipation.

The AFE031 is housed in a thermally-enhanced, surface-mount PowerPAD package (QFN-48). Operation is specified over the extended industrial junction temperature range of –40°C to +125°C.

The AFE031 is a low-cost, integrated, powerline communications (PLC) analog front-end (AFE) device that is capable of capacitive- or transformer-coupled connections to the powerline while under the control of a DSP or microcontroller. It is ideal for driving low-impedance lines that require up to 1.5 A into reactive loads. The integrated receiver is able to detect signals down to 20 µVRMS and is capable of a wide range of gain options to adapt to varying input signal conditions. This monolithic integrated circuit provides high reliability in demanding powerline communications applications.

The AFE031 transmit power amplifier operates from a single supply in the range of 7 V to 24 V. At maximum output current, a wide output swing provides a 12-VPP (IOUT = 1.5 A) capability with a nominal 15-V supply. The analog and digital signal processing circuitry operates from a single 3.3-V power supply.

The AFE031 is internally protected against overtemperature and short-circuit conditions. It also provides an adjustable current limit. An interrupt output is provided that indicates both current limit and thermal limit. There is also a shutdown pin that can be used to quickly put the device into its lowest power state. Through the four-wire serial peripheral interface, or SPI™, each functional block can be enabled or disabled to optimize power dissipation.

The AFE031 is housed in a thermally-enhanced, surface-mount PowerPAD package (QFN-48). Operation is specified over the extended industrial junction temperature range of –40°C to +125°C.

다운로드 스크립트와 함께 비디오 보기 동영상

관심 가지실만한 유사 제품

open-in-new 대안 비교
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능
OPA521 활성 2.5A 협대역 라인 드라이버 Lower cost discrete solution alternative

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
8개 모두 보기
유형 직함 날짜
* Data sheet AFE031 Powerline Communications Analog Front-End datasheet (Rev. E) PDF | HTML 2019/06/17
Application brief Power Line Communication in Solar Applications PDF | HTML 2024/12/12
Application note Interfacing the C2000 with an AFE03x: B-FSK Example (Rev. D) PDF | HTML 2022/02/15
E-book The Signal e-book: A compendium of blog posts on op amp design topics 2017/03/28
E-book Analog Engineer’s Pocket Reference Guide Fifth Edition (Rev. D) PDF | HTML 2014/09/30
User guide TINA Simulation Schematic of a Two-Node, Power-Line Communication System 2013/09/06
More literature Efficiency from Metering to Service Solutions 2012/10/17
Application note AFE Design for a Narrowband Power-Line Communications Modem Using the AFE031 (Rev. A) 2011/11/03

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

BOOSTXL-AFE031-DF1 — SunSpec 호환 PLC BoosterPack™

BOOSTXL-AFE031-DF1 평가 모듈은 TI의 통합 전력선 통신(PLC) 아날로그 프론트 엔드 장치인 AFE031을 갖추고 있습니다. 지원되는 C2000™ MCU LaunchPad™ 개발 키트와 페어링될 경우, BoosterPack™ 플러그인 모듈은 PLC 애플리케이션, 특히 SunSpec 급속 셧다운을 위한 강력한 평가 플랫폼을 제공합니다.
사용 설명서: PDF
TI.com에서 구매 불가
소프트웨어 개발 키트(SDK)

TI-PLC-PRIME-DC Power Line Communications PRIME Data Concentrator Software Development Kit

PRIME standard for narrowband OFDM Power Line Communications. The data concentrator solution is designed for the head-end systems which communicate with the end meters (“service node”) in the neighborhood area network.

 

The TI PRIME data concentrator system relies on the AM3356 ARM Cortex-A8 (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
전력 연산 증폭기
AFE031 저임피던스 라인 구동을 위한 1,500mA, 통합형, PLC(전력선 통신) 아날로그 프론트 엔드
소프트웨어 개발 키트(SDK)

TI-PLC-PRIME-SN Power Line Communications PRIME Software Development Kit

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
전력 연산 증폭기
AFE031 저임피던스 라인 구동을 위한 1,500mA, 통합형, PLC(전력선 통신) 아날로그 프론트 엔드
소프트웨어
소프트웨어 개발 키트(SDK)
TI-PLC-PRIME-DC PRIME 데이터 집신기 전력선 통신 모뎀
시뮬레이션 모델

AFE031 IBIS Model

SLAM065.ZIP (60 KB) - IBIS Model
시뮬레이션 모델

AFE031 PSpice Model (Rev. A)

SLAM240A.ZIP (43 KB) - PSpice Model
시뮬레이션 모델

AFE031 TINA-TI Reference Design

SBOMC53.TSC (39 KB) - TINA-TI Reference Design
시뮬레이션 모델

AFE031 TINA-TI Spice Model

SBOMC54.ZIP (6 KB) - TINA-TI Spice Model
시뮬레이션 모델

TINA Simulation Schematic - Two-node PLC System

SBOM841.ZIP (356 KB) - TINA-TI Spice Model
계산 툴

ANALOG-ENGINEER-CALC — 아날로그 엔지니어의 계산기

아날로그 엔지니어의 계산기는 아날로그 회로 설계 엔지니어가 정기적으로 사용하는 많은 반복 계산의 속도를 높이도록 설계되었습니다. 이 PC 기반 툴은 피드백 저항을 사용한 연산 증폭기 게인 설정부터 아날로그-디지털 컨버터(ADC) 드라이브 버퍼 회로 안정화를 위한 적절한 회로 설계 요소 선택에 이르기까지 다양한 일반적인 계산 목록이 포함된 그래픽 인터페이스를 제공합니다.

이 계산기는 독립 실행형 툴로 유용할 뿐만 아니라 아날로그 엔지니어의 포켓 레퍼런스에 설명된 개념과도 잘 어울립니다.

시뮬레이션 툴

PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®

TI용 PSpice®는 아날로그 회로의 기능을 평가하는 데 사용되는 설계 및 시뮬레이션 환경입니다. 완전한 기능을 갖춘 이 설계 및 시뮬레이션 제품군은 Cadence®의 아날로그 분석 엔진을 사용합니다. 무료로 제공되는 TI용 PSpice에는 아날로그 및 전력 포트폴리오뿐 아니라 아날로그 행동 모델에 이르기까지 업계에서 가장 방대한 모델 라이브러리 중 하나가 포함되어 있습니다.

TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 착수하기 (...)
시뮬레이션 툴

TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
사용 설명서: PDF
레퍼런스 디자인

TIDA-010949 — 유선 및 무선 통신을 지원하는 GaN 기반의 600W 태양광 전력 옵티마이저 레퍼런스 디자인

이 레퍼런스 디자인은 최대 80V 입력 전압 및 80V의 출력 전압을 지원하고 최대 18A의 출력과 입력 전류를 제공하는 태양광 전력 옵티마이저입니다. 이 설계는 구성 가능한 4스위치 벅-부스트 컨버터를 사용하여 패널 전류를 스트링 전류로 스텝 업 또는 스텝 다운합니다. 바이패스 회로는 스마트 다이오드 컨트롤러 기반 설계를 사용합니다.

이 레퍼런스 디자인PLC(전력선 통신)를 포함하고 있으며 무선 통신도 지원합니다. 디지털 제어와 통신은 모두 단일 C2000™ MCU(마이크로컨트롤러)에서 구현됩니다.

Design guide: PDF
레퍼런스 디자인

TIDA-060001 — SunSpec 급속 셧다운 전송 및 수신 레퍼런스 설계

이 레퍼런스 설계에서는 C2000 MCU와 AFE031 전력선 통신 아날로그 프론트 엔드를 인터페이싱하고 FSK(주파수 전환 키잉)를 사용하여 유선 연결 인터페이스를 통해 데이터를 보내고 받습니다. 이 설계는 FSK(fM: 131.25KHz 및 fS: 143.75KHz)를 사용하여 특정 33비트 워드 패킷을 전송하는 SunSpec 표준 프로토콜을 보여줍니다. 이 설계의 목적은 태양광 인버터에서 PV(태양광) 모듈로 통신하는 통합 시스템 솔루션에서 유지 신호를 제공하는 것입니다.
Design guide: PDF
회로도: PDF
패키지 CAD 기호, 풋프린트 및 3D 모델
VQFN (RGZ) 48 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상