SDAA503 September   2026 F28E120SB , F28E120SC , F29H850DM , F29H850TU , F29H859TU-Q1 , F29P329SM-Q1 , F29P589DM-Q1 , F29P589DU-Q1 , TMS320F2800132 , TMS320F2800133 , TMS320F2800135 , TMS320F2800137 , TMS320F2800152-Q1 , TMS320F2800153-Q1 , TMS320F2800154-Q1 , TMS320F2800155 , TMS320F2800155-Q1 , TMS320F2800156-Q1 , TMS320F2800157 , TMS320F2800157-Q1 , TMS320F280021 , TMS320F280021-Q1 , TMS320F280023 , TMS320F280023-Q1 , TMS320F280023C , TMS320F280025 , TMS320F280025-Q1 , TMS320F280025C , TMS320F280025C-Q1 , TMS320F280033 , TMS320F280034 , TMS320F280034-Q1 , TMS320F280036-Q1 , TMS320F280036C-Q1 , TMS320F280037 , TMS320F280037-Q1 , TMS320F280037C , TMS320F280037C-Q1 , TMS320F280038-Q1 , TMS320F280038C-Q1 , TMS320F280039 , TMS320F280039-Q1 , TMS320F280039C , TMS320F280039C-Q1 , TMS320F280040-Q1 , TMS320F280040C-Q1 , TMS320F280041 , TMS320F280041-Q1 , TMS320F280041C , TMS320F280041C-Q1 , TMS320F280045 , TMS320F280048-Q1 , TMS320F280048C-Q1 , TMS320F280049 , TMS320F280049-Q1 , TMS320F280049C , TMS320F280049C-Q1 , TMS320F28075 , TMS320F28075-Q1 , TMS320F28076 , TMS320F28374D , TMS320F28374S , TMS320F28375D , TMS320F28375S , TMS320F28375S-Q1 , TMS320F28376D , TMS320F28376S , TMS320F28377D , TMS320F28377S , TMS320F28377S-Q1 , TMS320F28378D , TMS320F28378S , TMS320F28379D , TMS320F28379D-Q1 , TMS320F28379S , TMS320F28384D , TMS320F28384D-Q1 , TMS320F28384S , TMS320F28384S-Q1 , TMS320F28386D , TMS320F28386D-Q1 , TMS320F28386S , TMS320F28386S-Q1 , TMS320F28388D , TMS320F28388S , TMS320F28P550SG , TMS320F28P550SJ , TMS320F28P551SG , TMS320F28P559SG-Q1 , TMS320F28P559SJ-Q1 , TMS320F28P650DH , TMS320F28P650DK , TMS320F28P650SH , TMS320F28P650SK , TMS320F28P659DH-Q1 , TMS320F28P659DK-Q1 , TMS320F28P659SH-Q1

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1 Introduction
  5. 2 Pierce Oscillator and Crystal Model
    1. 2.1 Oscillator Block Diagram
    2. 2.2 Quartz Crystal Electrical Model
  6. 3 Crystal Selection Criteria
    1. 3.1 Why ESR Governs Crystal Compatibility
    2. 3.2 Crystal Frequency
    3. 3.3 Shunt Capacitance C0
  7. 4 Step-by-step Crystal Selection Process
    1. 4.1 Step 1 - Verify ESR Meets Oscillator Requirements
    2. 4.2 Step 2 - Size Load Capacitors CL1 and CL2
    3. 4.3 Step 3 - Determine if Damping Resistor Rd is Required
    4. 4.4 Step 4 - Calculate Rd (Damping Resistor)
    5. 4.5 Step 5 - Verify Negative Resistance (Rneg) Margin
  8. 5 PCB Layout Recommendations
    1. 5.1 Crystal Placement
    2. 5.2 Load Capacitor Placement
    3. 5.3 Trace Routing
    4. 5.4 Shielding Considerations
  9. 6 Testing and Validation
    1. 6.1 Measurement Equipment Requirements
    2. 6.2 Frequency Verification
    3. 6.3 Start-Up Time Measurement
    4. 6.4 Negative Resistance (Rneg) Measurement
  10. 7 Common Issues and Debug Tips
  11. 8 Design Example - 20MHz Crystal
  12. 9 Appendix A
    1. 9.1 Crystal Selection for Generic Pierce Oscillators
      1. 9.1.1 Introduction and Scope
      2. 9.1.2 Theoretical Background
      3. 9.1.3 Method A - Analytical Derivation from gm_min
        1. 9.1.3.1 Equipment and Component Requirements
        2. 9.1.3.2 Procedure
        3. 9.1.3.3 Single-Frequency Oscillator Considerations
        4. 9.1.3.4 Worked Example — 40MHz Fixed-Frequency Oscillator
      4. 9.1.4 Method B - Empirical Derivation using Negative Resistance Test
        1. 9.1.4.1 Equipment and Component Requirements
        2. 9.1.4.2 Signal Generator as Crystal Substitute
        3. 9.1.4.3 Equations
        4. 9.1.4.4 Procedure
        5. 9.1.4.5 Alternative Experimental Methods for Deriving gm
          1. 9.1.4.5.1 Load Capacitance (CL) Sweep
          2. 9.1.4.5.2 Supply Voltage (VDD) Sweep
          3. 9.1.4.5.3 Temperature Sweep (Thermal Margin Identification)
        6. 9.1.4.6 Generating a Custom ESR/CL Requirement Table
      5. 9.1.5 Method C - Frequency Pulling Characterization
        1. 9.1.5.1 Required Equipment and Components
        2. 9.1.5.2 Equations
        3. 9.1.5.3 Procedure
        4. 9.1.5.4 Worked Example - 40MHz Frequency Pulling
      6. 9.1.6 Summary Checklist - Generic Pierce Oscillator Crystal Selection
  13. 10References
Load Capacitance (CL) Sweep

This is the simplest method requiring no modifications to the PCB beyond swapping load capacitors. The margin can be read directly as a ratio without computing gm explicitly.

Equipment required: Precision C0G/NP0 capacitor kit (8pF to 47pF, ±0.5%), XCLKOUT frequency counter.

  1. Install production CL1 = CL2 = CL_design. Confirm oscillation through XCLKOUT.
  2. Replace CL1 and CL2 simultaneously with progressively larger values (same value both sides). Use the capacitor kit in 2pF to 3pF steps.
  3. After each step, wait ≥ 30s and verify oscillation. Record the largest CL value at which oscillation still occurs: this is CL_crit.
  4. Compute gm from the critical condition (Rneg = ESR at CL_crit, margin = 1):
Equation 29. gm = ESR × ω²×CL_crit²

The safety margin at the production CL without computing gm is given directly by:

Equation 30. Margin = (CL_crit / CL_design)²

If CL_crit ≥ √3 × CL_design ≈ 1.73 × CL_design, the 3× Rneg margin is satisfied. For 5× automotive margin: CL_crit ≥ √5 × CL_design ≈ 2.24 × CL_design.

Example: CL_design = 18pF, CL_crit = 36pF. Margin = (36 / 18)2 = 4×. Passes 3× standard; marginal for 5× automotive. gm = 40Ω × (2π × 20 × 106)2 × (36 × 10-12)2 = 40 × 1.58 × 1016 × 1.30 × 10-21 = 8.2mA/V.

Note: CL_crit found at room temperature and nominal VDD is not gm_min. Repeat the sweep at maximum operating temperature and minimum VDD to find the worst-case CL_crit and the true gm_min.