TPS61201

ACTIVE

0.3V Input, 3.3V Output Voltage Boost Converter with 1.3A Switches and 'Down Mode' in a 3x3 QFN

Top

Product details

Parameters

Vin (Min) (V) 0.3 Vin (Max) (V) 5.5 Vout (Min) (V) 3.3 Vout (Max) (V) 3.3 Switch current limit (Typ) (A) 1.35 Regulated outputs (#) 1 Switching frequency (Min) (kHz) 1250 Switching frequency (Max) (kHz) 1650 Iq (Typ) (mA) 0.05 Features Synchronous Rectification Duty cycle (Max) (%) 95 Operating temperature range (C) -40 to 85 Rating Catalog open-in-new Find other Boost converters (integrated switch)

Package | Pins | Size

VSON (DRC) 10 9 mm² 3 x 3 VSON (DRC) 10 9 mm² 3.00 x 3.00 open-in-new Find other Boost converters (integrated switch)

Features

  • More than 90% Efficiency at
    • 300 mA Output Current at 3.3 V
      (VIN ≥ 2.4 V)
    • 600 mA Output Current at 5 V (VIN ≥ 3 V)
  • Automatic Transition between Boost Mode and
    Down Conversion Mode
  • Device Quiescent Current Less than 55 µA
  • Startup into Full Load at 0.5 V Input Voltage
  • Operating Input Voltage Range from
    0.3 V to 5.5 V
  • Programmable Undervoltage Lockout Threshold
  • Output Short Circuit Protection Under all Operating
    Conditions
  • Fixed and Adjustable Output Voltage Options from
    1.8 V to 5.5 V
  • Power Save Mode for Improved Efficiency at Low
    Output Power
  • Forced Fixed Frequency Operation Possible
  • Load Disconnect During Shutdown
  • Overtemperature Protection
  • Small 3 mm × 3 mm VSON-10 Package
open-in-new Find other Boost converters (integrated switch)

Description

The TPS6120x devices provide a power supply solution for products powered by either a single-cell, two-cell, or three-cell alkaline, NiCd or NiMH, or one-cell Li-Ion or Li-polymer battery. It is also used in fuel cell or solar cell powered devices where the capability of handling low input voltages is essential. Possible output currents depend on the input to output voltage ratio. The devices provide output currents of up to 600 mA at a 5-V output, while using a single-cell Li-Ion or Li-Polymer battery and discharges it down to 2.6 V. The boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using synchronous rectification to obtain maximum efficiency. At low load currents, the converter enters the Power Save mode to maintain a high efficiency over a wide load current range. The Power Save mode can be disabled, forcing the converter to operate at a fixed switching frequency. The average input current is limited to a maximum value of 1500 mA. The output voltage is programmed by an external resistor divider, or is fixed internally on the chip. The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. The device is packaged in a 10-pin VSON package measuring 3 mm × 3 mm.

open-in-new Find other Boost converters (integrated switch)
Download

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 10
Type Title Date
* Datasheet TPS6120x Low Input Voltage Synchronous Boost Converter With 1.3-A Switches datasheet (Rev. E) Dec. 24, 2014
Application note Performing Accurate PFM Mode Efficiency Measurements (Rev. A) Dec. 11, 2018
Application note QFN and SON PCB Attachment (Rev. B) Aug. 24, 2018
Selection guide Power Management Guide 2018 (Rev. R) Jun. 25, 2018
Application note Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) Nov. 29, 2017
Application note Extending the Soft Start Time Without a Soft Start Pin (Rev. B) Jun. 15, 2017
Application note Five Steps to a Good PCB Layout of the Boost Converter May 03, 2016
Application note Basic Calculation of a Boost Converter's Power Stage (Rev. C) Jan. 08, 2014
Application note IQ: What it is, what it isn’t, and how to use it Jun. 17, 2011
Application note Minimizing Ringing at the Switch Node of a Boost Converter Sep. 15, 2006

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARD Download
49
Description

The TPS61201EVM-179 is an evaluation module for the TPS61201 low input voltage synchronous boost converter. The TPS61200 provides a power supply solution for products powered by either a single-cell, two-cell, or three-cell alkaline, NiCd or NiMH, or one-cell Li-Ion or Li-polymer battery.

Features
  • Input voltage: 0.3 V to 5.5 V
  • Startup into full load at 0.5 V input voltage
  • Fixed output voltage: 3.3 V
  • Switch current limit: 1.5 A (max)
  • More than 90% efficiency at:
    • 600 mA output current at 3.3 V (VIN ≥ 1.2 V)
    • 600 mA output current at 5 V (VIN ≥ 3.3 V)
  • Quiescent current: < 55 μA
  • Package: 3x3 QFN

Design tools & simulation

SIMULATION TOOL Download
PSpice® for TI design and simulation tool
PSPICE-FOR-TI — PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Features
  • Leverages Cadence PSpice Technology
  • Preinstalled library with a suite of digital models to enable worst-case timing analysis
  • Dynamic updates ensure you have access to most current device models
  • Optimized for simulation speed without loss of accuracy
  • Supports simultaneous analysis of multiple products
  • (...)
GERBER FILE Download
SLVC123.ZIP (107 KB)

CAD/CAE symbols

Package Pins Download
VSON (DRC) 10 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos