Home Energiemanagement DC/DC-Schaltregler DC/DC-Controller
Home
Energiemanagement
DC/DC-Schaltregler
DC/DC-Controller

LM51772-Q1

AKTIV

Abwärts-/Aufwärtswandler für die Automobilindustrie mit 4 Schaltern und I2C-Schnittstelle, 55 V

Jetzt bestellen
Datenblatt

LM51772-Q1

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Rating Automotive Topology Buck-Boost Vin (max) (V) 55 Vin (min) (V) 0 Vout (max) (V) 55 Vout (min) (V) 1 Features 1% accuracy, AEC Q100, Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Advanced power saving, Dynamic voltage scaling, Enable, Extended power range, Frequency synchronization, I2C, Light-load efficiency, Load Disconnect, Power good, Spread Spectrum, Synchronous rectification, Tracking, USB C/PD compatible, UVLO adjustable EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 100 Iq (typ) (A) 0.00006 TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 150
Rating Automotive Topology Buck-Boost Vin (max) (V) 55 Vin (min) (V) 0 Vout (max) (V) 55 Vout (min) (V) 1 Features 1% accuracy, AEC Q100, Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Advanced power saving, Dynamic voltage scaling, Enable, Extended power range, Frequency synchronization, I2C, Light-load efficiency, Load Disconnect, Power good, Spread Spectrum, Synchronous rectification, Tracking, USB C/PD compatible, UVLO adjustable EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 100 Iq (typ) (A) 0.00006 TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 150
VQFN (RHA) 40 36 mm² (6 mm × 6 mm)
  • Input range from 0V (V(BIAS) ≥ 3.5V) to 55V
  • Output voltage 1V to 55V
  • Dynamical Vo programming via I2C from:
    • 3.3V up to 48V in 20mV steps
    • 1V up to 24V in 10mV steps
  • Peak current regulation control
  • Small voltage transition ripple overall operating modes
  • Shut down quiescent current 3µA
  • Operating quiescent current 60µA
  • DRV pin for external FET control
  • Operation mode selection for high efficiency in light load and high load conditions:
    • Power save mode (Single Pulse/µSleep)
    • Automatic/programmable conduction mode
  • Integrated high voltage supply LDO
  • Auxiliary high voltage LDO/reference
  • Integrated full-bridge gate drive
    • 2A peak current capability
    • Bootstrap over and under-voltage protection
    • Integrated boot-strap diode
  • Fixed frequency independent from operating mode (boost, buck-boost, buck)
    • Forced PWM mode selectable
    • Switching frequency from 100kHz to 2.2MHz
    • External clock synchronization and clock output
  • Average input or output current sensor
    • Programmable from 0.5A (5mV) to 7A (70mV) in 50mA (500µV) steps
    • ISET pin selectable
  • I2C programmable with diagnostics
    • I2C usage is optional, alternative feature selection via CFG-Pins
  • Automotive temperature range (Tj = -40°C to 150°C)
  • 40-Pin WSON package with wettable flanks

  • Create a custom design using the LM51772-Q1 with the WEBENCH® Power Designer

  • Input range from 0V (V(BIAS) ≥ 3.5V) to 55V
  • Output voltage 1V to 55V
  • Dynamical Vo programming via I2C from:
    • 3.3V up to 48V in 20mV steps
    • 1V up to 24V in 10mV steps
  • Peak current regulation control
  • Small voltage transition ripple overall operating modes
  • Shut down quiescent current 3µA
  • Operating quiescent current 60µA
  • DRV pin for external FET control
  • Operation mode selection for high efficiency in light load and high load conditions:
    • Power save mode (Single Pulse/µSleep)
    • Automatic/programmable conduction mode
  • Integrated high voltage supply LDO
  • Auxiliary high voltage LDO/reference
  • Integrated full-bridge gate drive
    • 2A peak current capability
    • Bootstrap over and under-voltage protection
    • Integrated boot-strap diode
  • Fixed frequency independent from operating mode (boost, buck-boost, buck)
    • Forced PWM mode selectable
    • Switching frequency from 100kHz to 2.2MHz
    • External clock synchronization and clock output
  • Average input or output current sensor
    • Programmable from 0.5A (5mV) to 7A (70mV) in 50mA (500µV) steps
    • ISET pin selectable
  • I2C programmable with diagnostics
    • I2C usage is optional, alternative feature selection via CFG-Pins
  • Automotive temperature range (Tj = -40°C to 150°C)
  • 40-Pin WSON package with wettable flanks

  • Create a custom design using the LM51772-Q1 with the WEBENCH® Power Designer

The LM51772-Q1 is a four switch Buck-Boost controller with optional I2C control. The device provides a regulated output voltage if the input voltage is higher, equal or lower than the adjusted output voltage. In power safe mode the device supports very high efficiency at light and high load conditions and features a programmable pass-through function(PCM). The second over-voltage protection is user programmable and can be used to limit the voltage during moisture (test) conditions. Numerous monitoring features like a thermal warning help to maintain the system housekeeping.

LM51772-Q1 runs at a fixed switching frequency, which can be set via the RT/SYNC pin. The switching frequency remains the same during buck, boost and buck-boost operation. The device maintains small mode transition ripple overall operating modes. The integrated and optional high-side current sensor features an accurate output or input current limitation. The average current limit of the LM51772-Q1 is also configurable through the I2C interface.

The LM51772-Q1 is a four switch Buck-Boost controller with optional I2C control. The device provides a regulated output voltage if the input voltage is higher, equal or lower than the adjusted output voltage. In power safe mode the device supports very high efficiency at light and high load conditions and features a programmable pass-through function(PCM). The second over-voltage protection is user programmable and can be used to limit the voltage during moisture (test) conditions. Numerous monitoring features like a thermal warning help to maintain the system housekeeping.

LM51772-Q1 runs at a fixed switching frequency, which can be set via the RT/SYNC pin. The switching frequency remains the same during buck, boost and buck-boost operation. The device maintains small mode transition ripple overall operating modes. The integrated and optional high-side current sensor features an accurate output or input current limitation. The average current limit of the LM51772-Q1 is also configurable through the I2C interface.
filter Andere DC/DC-Controller suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 6
Top-Dokumentation Typ Titel Format-Optionen Neueste englische Version herunterladen Datum
* Datenblatt LM51772-Q1 55V 4-Switch Buck-Boost Controller with I2 C interface datasheet (Rev. A) PDF | HTML 21.10.2025
Zertifikat LM51772Q1EVM-HP EU Declaration of Conformity (DoC) 21.10.2025
Application brief Using the DRV1 Pin on LM51772 and LM251772 PDF | HTML 29.07.2025
Anwendungshinweis Battery or Capacitor Backup Operation with the LM51772 09.07.2025
Informationen zur funktionalen Sicherheit LM51772-Q1 and LM251772-Q1 Functional Safety FIT Rate and FMD PDF | HTML 05.05.2025
Anwendungshinweis Layout Optimization of 4-Switch Buck-Boost Converters PDF | HTML 05.09.2023

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

LM51772EVM-HP — LM51772 – Evaluierungsmodul

Das LM51772EVM-HP zeigt ein flexibles, leistungsstarkes Abwärts-/Aufwärts-Design unter Verwendung des Abwärts-/Aufwärts-Controllers LM51772 mit großem VIN-Eingangsspannungsbereich. Das Evaluierungsmodul ist für den Betrieb im Eingangsspannungsbereich von 9 V bis 48 V konfiguriert und bietet einen (...)

Benutzerhandbuch: PDF | HTML
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
Evaluierungsplatine

LM51772Q1EVM-HP — LM51772-Q1 – Evaluierungsmodul

Das LM51772Q1EVM-HP zeigt ein flexibles, leistungsstarkes Abwärts-/Aufwärts-Design unter Verwendung des LM51772Q1. Das Evaluierungsmodul ist für den Betrieb im Eingangsspannungsbereich von 9 V bis 30 V konfiguriert und erzeugt einen geregelten 12 V-Ausgang mit bis zu 17 A Laststrom. Das EVM (...)
Benutzerhandbuch: PDF | HTML
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
GUI für Evaluierungsmodul (EVM)

LM51772-CONFIGURATON-GUI — LM51772 GUI for configuration via I2C

Graphical User Interface (GUI) to configure the LM51772 via I2C. You can use the Launch button for using the GUI online via a browser or one of the download files to operate the GUI offline
Unterstützte Produkte und Hardware
Berechnungstool

LM51772-QUICKSTART-CALC — LM51772 BuckBoost Quickstart Calculator Tool

LM51772 BuckBoost Quickstart Calculator Tool. This standalone tool facilitates and assists the power supply engineer with the design of a DC/DC buck-boost converter based on the LM51772.
Unterstützte Produkte und Hardware
Berechnungstool

TPS61383Q-SCAP-CALC — TPS61383-Q1 Super Capacitor Energy Calculation Tool.

TPS61383-Q1 Super Capacitor Energy Calculation Tool. This standalone tool assists the power supply engineer with the design of a super capacitor e-latch / CPM system using DC-DC converter
Unterstützte Produkte und Hardware
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
VQFN (RHA) 40 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos